Danfoss Link RS Manuel utilisateur
MAKING MODERN LIVING POSSIBLE
Danfoss Heating Solutions
Danfoss Link™ RS Room Sensor
Installation Guide
2VIFZA35X © Danfoss 02/2011
Installation Guide Danfoss Link™ RS
Installation Guide
Installationsanleitung
Guide d’installation
Installationsmanual
Installationshandbok
Asennusohje
Installatiehandleiding
Instrukcja instalacji
Instalační příručka
3
VIFZA35X © Danfoss 02/2011
Installation Guide Danfoss Link™ RS
GB
DE
FR
DK
SE
FI
NL
PL
CZ
4VIFZA35X © Danfoss 02/2011
Introduction ............................................. 5
Display symbols.......................................... 5
Installation............................................... 6
Adding device ........................................... 8
Perform network test..................................... 8
Factory reset............................................. 9
Trouble shooting........................................ 10
Technical specifications ................................. 11
Disposal instructions.................................... 11
Index
Installation Guide Danfoss Link™ RS
5
VIFZA35X © Danfoss 02/2011
Ambient temperature
Floor temperature
Communication/link test
Battery warning
Tamper proof, locked by CC
The Danfoss Link™ RS (Room Sensor) has a built-in tem-
perature sensor, which measures the ambient temperature.
It allows you to control the heating, based on room tem-
perature in the room where installed. With the Danfoss
Link™ RS you can also adjust the temperature.
LED button for
display light on/off
and for network test
Temperature up
Display (backlit) Temperature down
The RS Room Sensor is battery powered - 2 x AA - and can
thus be placed everywhere it fits the interior design.
Introduction
Display symbols
GB
Installation Guide Danfoss Link™ RS
6VIFZA35X © Danfoss 02/2011
Installation
The Danfoss Link™ wireless system’s transmission range is
sufficient for most applications; however each building has
different obstacles affecting communication and maximum
transmission distance.
If communication problems occur Danfoss suggests that
accessories would be required to support the system, such as
repeaters. In exceptional cases the wireless system may not
be suitable for your installation.
Please be aware of the following, when installing Danfoss
Link™ RS:
Do not install Danfoss Link™ RS, where it will be subject to
direct sunlight.
The installation height should typically be between 80-
150 cm.
In wet rooms it shall be installed according to local
building regulations.
At least 50 cm away from windows/doors that will be left
open occasionally.
Installation Guide Danfoss Link™ RS
7
VIFZA35X © Danfoss 02/2011
Installation
1. Turn the device around so the
back is facing you.
2. Remove the back panel by gently
pressing your thumbs on the
panel and pull downwards.
3. Fix the back panel to the wall
either help of screws or adhesive
on the desired destination.
4. Insert the batteries.
5. Install the Danfoss Link™ RS front
by gently letting it slide on the
back panel again.
GB
Installation Guide Danfoss Link™ RS
8VIFZA35X © Danfoss 02/2011
Adding device
When the RS unit has been
added to the Danfoss Link™
CC Central Controller, a
network test should be
performed.
For more information on
network tests, see the
Danfoss Link™ CC instruction
manual: Configuration 8:
Perform network test.
At the end of the network test you will be informed that the
test is waiting for signal from the RS unit.
Go to the RS unit and press the LED button for 5 seconds to
force the signal.
Max. 1 m
Perform network test
Connection of the RS Room Sensor
to a system is made from the Danfoss
Link™ CC Central Controller.
For further information, see
the Danfoss Link™ CC
instruction manual:
Configuration 6:
Adding devices.
Installation Guide Danfoss Link™ RS
9
VIFZA35X © Danfoss 02/2011
1. Remove the Danfoss Link™ RS
front from the back panel.
2. Turn the Danfoss Link™ RS around
so the back is facing you.
3. Remove one of the batteries.
4. Press and hold the button while
reinserting the battery until LED
flashes red (approx. 5 seconds).
5. Replace the Danfoss Link™ RS
front again on the back panel.
6. The Danfoss Link™ RS is now reset.
Factory reset
5 sec.
GB
Installation Guide Danfoss Link™ RS
10 VIFZA35X © Danfoss 02/2011
Short green flash Not included in network
Green fast flash Inclusion in progress
Red flash +
for 5 sec. Inclusion failed
ON Link test in progress
Red flash +
for 5 sec. Link test failed
ON + Red LED
flash every 2½ min. Low battery level
ON + Red LED
flash every 30 sec. Critical battery level
E5 Floor sensor short circuited
E6 Floor sensor lost
ON Tamper proof enabled by
Danfoss Link™ CC
Flash Limited by Danfoss Link™ CC
Trouble shooting
Installation Guide Danfoss Link™ RS
Autres manuels pour Link RS
1
Table des matières
Langues :
Autres manuels Danfoss Accessoires
Danfoss
Danfoss TS3 Manuel utilisateur
Danfoss
Danfoss AKS 4100 Manuel utilisateur
Danfoss
Danfoss AKS 4100 Manuel utilisateur
Danfoss
Danfoss AKS 4100U Manuel utilisateur
Danfoss
Danfoss 176F6757 Manuel utilisateur
Danfoss
Danfoss DGS Series Manuel utilisateur
Danfoss
Danfoss DGS-IR CO2 Manuel utilisateur
Danfoss
Danfoss DST X510 Manuel utilisateur
Danfoss
Danfoss DEVIreg 850 Manuel utilisateur
Danfoss
Danfoss 084H4505 Manuel utilisateur
Danfoss
Danfoss 176F6516 Manuel utilisateur
Danfoss
Danfoss 086U9563 Manuel utilisateur
Danfoss
Danfoss AKS 4100 Manuel utilisateur
Danfoss
Danfoss AKS 41 Manuel utilisateur
Danfoss
Danfoss 088U0213 Manuel utilisateur
Danfoss
Danfoss Z-Wave RS Manuel utilisateur
Danfoss
Danfoss DGS Series Manuel utilisateur
Danfoss
Danfoss DGS Manuel utilisateur
Danfoss
Danfoss KPP Pulse Pickup Manuel
Danfoss
Danfoss AKS 41U Manuel utilisateur
