Dahua IPCHDBW3300N Manuel utilisateur
HD IR Vandal Proof IP Dome Camera Quick Start Guide
Version 1.0
Welcome
Thank you for purchasing our IP camera!
This quick start guide is designed to be a reference tool for your system.
Please keep this start guide well for future reference.
Please open the accessory bag to check the items one by one in accordance with the list below.
Contact your local retailer ASAP if something is missing or damaged in the bag.
Before your operation please read the following instructions carefully.
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series IP camera should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name Amount
IPC Unit 1
MD9M data converter cable 1
Accessories bag 1
Quick Start Guide 1
Warranty Card 1
Certificate Card 1
CD 1
Table of Contents
1Framework...................................................................................................................................5
1.1 MD9M Data Converter Cable .....................................................................................5
1.2 Framework and Dimension.........................................................................................6
2Installation ...................................................................................................................................8
2.1 Device Installation ........................................................................................................8
2.2 SD Card Installation ...................................................................................................11
2.3 Lens Adjustment.........................................................................................................12
3Quick Configuration Tool.........................................................................................................13
3.1 Overview......................................................................................................................13
3.2 Operation .....................................................................................................................13
4Web Operation..........................................................................................................................16
4.1 Network Connection...................................................................................................16
4.2 Login and Logout........................................................................................................16
Appendix Toxic or Hazardous Materials or Elements ...............................................................19
5
1Framework
1.1 MD9M Data Converter Cable
You can refer to the following figure for MD9M data converter cable information. See Figure 1-1.
Figure 1-1
Please refer to the following sheet for detailed information.
Port Name Function Connection Note
VIDEO OUT Video output
port BNC Output analog video signal. It can connect to the
TV monitor to view the video.
AUDIO IN Audio input
port RCA Input audio signal. It can receive the analog audio
signal from the pickup.
AUDIO OUT Audio output
port RCA Output audio signal to the devices such as the
sound box.
12V DC/AC24V Power input
port / Power port. Input DC 12V/AC 24V
I/O I/O cable port / Connect to MD9M data converter cable.
LAN Network port Ethernet
port Connect to standard Ethernet cable.
Please refer to the follow sheet for detailed information of MD9M data converter cable.
Port Name Cable
Color Name Note
Yellow RS485_A RS485_A port. It is to control the PTZ.
Black RS485_B RS485_B port. It is to control the PTZ.
Red ALARM_COM Alarm output public port.
Brown ALARM_IN1 Alarm input port 1. It is to receive the on-off signal
from the external alarm source.
I/O Port
Pin
Grey ALARM_IN2
Alarm input port 2. It is to receive the on-off signal
from the external alarm source.
6
Port Name Cable
Color Name Note
White ALARM_NO
Alarm output port. It is to output the alarm signal
to the alarm device.
NO: normal open alarm output port.
It works with the ALARM_COM port.
Blue RESET
It is to restore factory default setup.
When the device is working properly, please
connect the blue cable (restore default setup port)
to the orange cable (GND signal) for 5 seconds,
the device can resume factory default setup.
Orange GND Ground port
1.2 Framework and Dimension
Please refer to the following figure for dimension information. The unit is mm. See Figure 1-2 and
Figure 1-3.
Figure 1-2
7
Figure 1-3
8
2Installation
This series IPC can be put on the table to realize surveillance. Or you can use the bracket or the
in-ceiling installation to realize the hang function. Please refer to the steps listed below.
2.1 Device Installation
Step 1
Use the inner hexagonal wrench (provided) to loose the three inner hexagon screws in the dome
cover and then open the cover. See Figure 2-1.
Figure 2-1
Step 2
Use the inner hexagonal wrench (provided) to loose the three inner hexagon screws in the dome
and then remove the device pedestal. See Figure 2-2.
9
Figure 2-2
Step 3
Draw out the cable exit and four screw holes in the installation position according to the device
pedestal. Dig the four plastic expansion bolt hole and cable exit. Insert the four plastic expansion
bolts into the screw holes
Step 4
Adjust the camera pedestal to the proper position and then draw the cable through the cable exit
you just dug in the ceiling (wall). Line up the four screw holes in the device pedestal to the four
plastic expansion bolt holes in the installation position. Put the four self-tapping screws in the
device pedestal and then use the screwdriver to secure the screws in the four plastic expansion
bolts firmly.
Step 5
Adjust the device position and line up the three inner hexagon screws of the device to the three
holes of the installation position. Put the three inner hexagon screws into the screw holes at the
bottom of the pedestal. Use the inner hexagon screwdriver to fix firmly. See Figure 2-3.
10
Figure 2-3
Step 6
Adjust the X-Y-Z axis module to turn the device to the proper monitor angle. Please follow the
steps listed below to adjust.
zSlightly loose the screws at the two sides of the X-Y-Z module manually, you can adjust the
module tilt rotation angle (15°～90°).
zSlightly loose the screw of the pressing slice, you can adjust the video rotation angle of the
module (0°～355°)
zAdjust the turning ring of the pedestal, you can adjust the module pan rotation angle (0°～
355°).
Please note, the screws in the following figure are the optical adjustment component.
Please make sure it is outward and do not allow it to touch the X-Y-Z axis module. See
Figure 2-4
Figure 2-4
Step 7
Put the dome cover back and then put the three inner hexagon screws into the holes of the
device. Use the inner hexagonal wrench to fasten these three screws. See Figure 2-5
Table des matières
Autres manuels Dahua Caméra de sécurité
Dahua
Dahua SE-DIR13MP36 Manuel utilisateur
Dahua
Dahua SD22404T-GN-W Manuel utilisateur
Dahua
Dahua IPC-HFW8331E-Z5 Manuel utilisateur
Dahua
Dahua N45EFNZ Manuel utilisateur
Dahua
Dahua ITC215-PW4I-LZF27135 Manuel utilisateur
Dahua
Dahua IPC-HF8232F-HDMI Manuel utilisateur
Dahua
Dahua Pinhole Manuel utilisateur
Dahua
Dahua ITC237-PW1B-IRZ Guide d'installation et d'utilisation
Dahua
Dahua HAC-HFW1800T-A-0280B Manuel utilisateur
Dahua
Dahua DHI-ITC215-PW6M-IRLZF-B Manuel utilisateur
Dahua
Dahua CPC4060LP Manuel utilisateur
Dahua
Dahua IPC-HDB/HDBW3202 Series Manuel utilisateur
Dahua
Dahua DH-SP-PIXX Manuel utilisateur
Dahua
Dahua F Series Manuel utilisateur
Dahua
Dahua IPC-HFW5849T1-ASE-LED-0360B Manuel utilisateur
Dahua
Dahua DH-IPC-HF8835FN Manuel utilisateur
Dahua
Dahua DH-IPC-PSD8802-A180 Manuel utilisateur
Dahua
Dahua HAC-HUM3100BP/N Manuel utilisateur
Dahua
Dahua PSD81602-A360 Manuel utilisateur
Dahua
Dahua DH-HAC-EB2401 Manuel utilisateur
