Dahua VTO2111D-WP Manuel de la liste des pièces

Autres manuels pour VTO2111D-WP

1

Ce manuel convient aux modèles suivants

1

Autres manuels Dahua Système d'interphone

Dahua

Dahua VTO2000A Series Manuel utilisateur

Dahua

Dahua VTO2111D-WP Manuel utilisateur

Dahua

Dahua Villa VTO Manuel utilisateur

Dahua

Dahua VTO5110B Manuel utilisateur

Dahua

Dahua VTH2611L-WP Manuel utilisateur

Dahua

Dahua VDP Series Manuel utilisateur

Dahua

Dahua KTA02 Manuel utilisateur

Dahua

Dahua VTO2202F Manuel utilisateur

Dahua

Dahua VTO2101E-P Manuel utilisateur

Dahua

Dahua VTO2000A-2 Manuel utilisateur

Dahua

Dahua DH-VTH111 Series Manuel utilisateur

Dahua

Dahua VTH5222CH Manuel utilisateur

Dahua

Dahua Villa Door Station Manuel utilisateur

Dahua

Dahua KTP02 Manuel utilisateur

Dahua

Dahua DHI-VTO4202F Series Manuel utilisateur

Dahua

Dahua Digital VTH Series Manuel utilisateur

Dahua

Dahua DHI-VTO2000-A-2-S Manuel utilisateur

Dahua

Dahua VTO6000A Manuel utilisateur

Dahua

Dahua VTO6 series Manuel utilisateur

Dahua

Dahua VTO Series Manuel utilisateur

Dahua

Dahua VTO5110B Manuel utilisateur

Dahua

Dahua DHI-VTH1550CH Manuel utilisateur

Dahua

Dahua VTO4202F-MK Manuel utilisateur

Dahua

Dahua VTO4202F-P Manuel utilisateur

Manuels Système d'interphone populaires d'autres marques

Bticino

Bticino LINEA 3000 Manuel utilisateur

MSI

MSI MSI-140 Manuel utilisateur

golmar

golmar Stadio Plus Manuel utilisateur

CyberData

CyberData 011211 series Manuel

Vidos

Vidos duo M1021 Manuel utilisateur

Vimar

Vimar ELVOX 7539/E Manuel utilisateur

SSS Siedle

SSS Siedle BTSV 850-03 Manuel utilisateur

Elvox

Elvox 5651 Manuel utilisateur

Videx

Videx VIDEOKIT Series Manuel utilisateur

Rocom

Rocom Doortello Business FW T2.05W2.04 Manuel utilisateur

Viking

Viking E-35-EWP Manuel utilisateur

Safeguard Supply

Safeguard Supply LRA-EX1000 Manuel utilisateur

SSS Siedle

SSS Siedle BFCV 850 Series Manuel utilisateur

GRD

GRD MAX V2 Manuel utilisateur

Alecto

Alecto ADI-250 Manuel utilisateur

Aiphone

Aiphone IE-8MD Manuel utilisateur

Perel

Perel EDB4 Manuel utilisateur

Bticino

Bticino Classe 300 Manuel utilisateur

Intercom Setup

VTH status indicator key:

Prerequisites

Power to the monitor and outdoor station (PoE or DC12V)

Wired or wireless network

Windows PC on the network



Step by Step Instructions

Below are several sets of instructions for setting up both the VTO and VTH system in their

respective interfaces.

Wired Instructions

Follow the instructions below for using a wired network (or PoE).

Video Instructions: VTO

VTO2111D-WP

1. Please plug in the appropriate power supply, the VTO2111D-WP can use PoE or a DC

power supply:

PoE:

DC power supply:

2. For this exercise, the VTO will have both DC power and a direct Ethernet connection

directly to a laptop for setup. After the unit has booted up make sure you have a network

connection to the device via an Ethernet cable.

3. If you are using a direct connection please set your devices IP address to 192.168.1.x

(x=any available IP), subnet mask 255.255.255.0. This will ensure you are using the same

IP scheme as the VTO's factory defaults.

4. Launch Internet Explorer and enter the VTO's default IP address into the URL address

bar: 192.168.1.110. If you cannot see the web page load on this default IP, then please press

and hold the reset button located on the back side of the VTO for 15 seconds while the

device is powered on. Once at the login page please enter the default username (admin) and

password (admin).

5. After the login page please select Network Config on the left side. Under the TCP/IP tab

please input the desired network configuration. For this exercise, the network uses a

192.168.2.x scheme, and the device will be configured on the wired interface (Eth0) and on

a static IP address on the LAN (DCHP-Off). After the settings have been entered, select OK.

Changing network schemes will disconnect the device when directly connected. From here

the device can now be plugged into the network, and accessed from the network.

6. To configure the Main VTH with the VTO we will need to add the VTH's room number (or

desired room number) to the VTO. Select Indoor Manager on the left, select Add, from here

the only necessary info will be the room number. For this example we will be using 9902 as

the Main VTH's room number, select OK when this is finished. *Note* The VTO's room

number can differ from this number (default of 6901), however this specific device can only

add one Main VTH (with multiple VTH extensions).

7. From here the VTO will use an auto negotiation protocol with the VTH. This process will

sometimes require rebooting the device. To access the software reboot on the VTO please

select Logout on the left side -> Reboot Device -> Reboot Device, and wait 2-5 minutes.

Please follow the second part of the Step by Step instructions to setup and configure the

VTH5221D

Video Instructions: VTH

VTH5221D

1. Please plug in the appropriate power supply, the VTH5221D can use PoE or a DC power

supply:

PoE:

DC power supply:

2. Once the VTH has booted up please tap the screen to wake up the main menu.

Press and hold Setting until a login menu appears on the screen.

Tap the area next to Password: and enter 888888 to get into the main settings of the device.

3. At the Network area of the VTH tap Wired IP.

4. Here you can set a static LAN IP, then select OK.

Alternatively you can use DHCP to grab an address from your Routers DHCP server, then

select OK.

5. To setup the Room No. tap the field and enter a four digit room number (or the number

that had been added on the VTO) then select OK.

6. Tap VTO Set on the left and enter the VTO IP Address, username, and password that you

configured in the VTO setup process.

Then Enable Status to ON.