Dadam micro GreenOK-II Manuel utilisateur
GreenOK-II : Wireless Thermo-Hygro Monitor
User’s Manual (Rev 2.1)
-X-
GreenOK-II : Wireless Thermo-Hygro Monitor
User’s Manual
G
G
G
G
G
G
G
G
G
G
G
"CAUTION: Exposure to Radio Frequency Radiation.
Antenna shall be mounted in such a manner to minimize the potential for human
contact during normal operation. The antenna should not be contacted during
operation to avoid the possiblility of exceeding the FCC radio frequency exposure
limit. The minimum separation distance of 20 cm from the antenna to the body of
user required.
GreenOK-II : Wireless Thermo-Hygro Monitor
User’s Manual (Rev 2.1)
-Z-
DOCUMENT HISTORY
REVISION DATE COMMENTS
1.0 2008.01.08 1ST official version (H/W Rev.A1)
2.0 2009.04.30 Modified as per H/W Rev.B3
2.1 2009.07.20 Modified as per H/W Rev.C1 & FCC
GreenOK-II : Wireless Thermo-Hygro Monitor
User’s Manual (Rev 2.1)
-[-
Table of Contents
DOCUMENT HISTORY...................................................................................... 3
1. Introduction .................................................................................................. 5
2. Systems Configuration ................................................................................ 7
3. Wireless Sensing Unit.................................................................................. 9
3.1 Functional Description ......................................................................... 9
3.2 How to set the DIP Switch #1 ............................................................. 11
3.3 How to set the DIP Switch #2 ............................................................. 12
3.4 How to connect the Sensors.............................................................. 13
4. Base Monitoring Unit ................................................................................. 14
4.1 Functional Description ....................................................................... 14
4.2 How to set the DIP Switch #1 ............................................................. 17
4.3 How to set the DIP Switch #2 ............................................................. 18
4.4 How to connect the Relay and AC Adapter....................................... 19
4.5 How to set Temperature Alarm Value ................................................ 20
5. Replacing the Batteries.............................................................................. 21
6. Specifications ............................................................................................. 22
6.1 GMS-120ZB.......................................................................................... 22
6.2 GMS-130ZB.......................................................................................... 22
6.3 GMS-140ZB.......................................................................................... 23
6.4 GMS-220ZB.......................................................................................... 24
6.5 GMS-220ZB-RPT.................................................................................. 24
GreenOK-II : Wireless Thermo-Hygro Monitor
User’s Manual (Rev 2.1)
-\-
1. Introduction
zThe GreenOK-II®Wireless Thermo-Hygro Monitor measures and transmits the temperature
and humidity via 2.4GHz Zigbee wireless technology. The Wireless Sensing Units(WSU) can
be installed anywhere within a 300 meters radius from the Base Monitoring Unit(BMU).
Adding on additional wireless sensing units couldn’t be easier. Once installed, the units work
together to keep you on top of the environmental conditions.
zIf the radio signal is week due to long distance than 300 meters or any radio obstacle exists, the
base monitoring units can be configured as a repeater unit which retransmits the neighboring
wireless sensing units data up to 8 depths.
zThe GreenOK-II®also monitors the voltages, relay contact point, or AC power failure up to 2
points.
zThe base monitoring unit receives the transmitted data from the wireless sensing units, displays
the current values, and alarm status. Pre-defined high or low temperature alarm conditions
trigger the red alarm indicators and the alarm sounds to notify you of the alarm situation in
real-time.
zThe GreenOK-II®can be applicable to below area.
9Green houses, farms, barns
9Warehouses for fresh foods, refrigerator, cold storage warehouses
9Museum, library, galleries
9Any temperature and relative humidity monitoring appliances
9Intelligent building and home automation
GreenOK-II : Wireless Thermo-Hygro Monitor
User’s Manual (Rev 2.1)
-]-
<Figure 1> Photos: Wireless Sensing Unit / Base Monitoring Unit
GreenOK-II : Wireless Thermo-Hygro Monitor
User’s Manual (Rev 2.1)
-^-
2. Systems Configuration
zGreenOK-II is composed of Wireless Sensing Unit(WSU) for temperature and humidity
monitoring and Base Monitoring Unit(BMU) for displaying the data from wireless sensing unit
and Wireless Repeater Unit(WRU) which retransmit the data from WSU.
zThe Wireless Sensing Unit (WSU) measures the temperature and humidity value and transmits
the data wirelessly to the base monitoring unit. It transmits the data over 2.4GHz radio
frequency band and operates with 2 C-size batteries, which can be installed and replaced very
easily by the end user.
zThe Base Monitoring Unit (BMU) receives the data from the wireless sensing units, displays
the current values, and alarm status. It operates with AC power adapter as well as with 2 C-size
batteries. Pre-defined high temperature and low temperature alarm conditions trigger the red
alarm indicators and the alarm sounds to notify you of the alarm situation in real-time. It can
also be operated as repeater mode, which the AC power adapter is suggested because of
relatively high battery consumption. Up to maximum 16 wireless sensing units can be
monitored simultaneously by base monitoring unit.
zThe Wireless Repeater Unit (WRU) retransmit the data between WSU and BMU up to 8 steps.
By using WRU, the longer radio monitoring distance can be achieved and also be applied to
cover geographical hidden area.
Type Model Name Description
Wireless Sensing Unit
(WSU)
GMS-120ZB TEMP & RH, 2 Volt Inputs
GMS-130ZB
GMS-140ZB 2 Volt Inputs
Base Monitoring Unit
(BMU) GMS-220ZB Monitor up to 16 Sensing Units
Wireless Repeater Unit
(WRU) GMS-220ZB-RPT Repeat up to 8 steps
<Table 1> GreenOK-II Product Information
GreenOK-II : Wireless Thermo-Hygro Monitor
User’s Manual (Rev 2.1)
-_-
1
Sensor ID
Wireless Sensing Unit
2
Sensor ID
Base Monitoring Unit
16
Sensor ID
Wireless Repeater Unit
<Figure 2> Systems Configuration
GreenOK-II : Wireless Thermo-Hygro Monitor
User’s Manual (Rev 2.1)
-`-
3. Wireless Sensing Unit
3.1 Functional Description
zSENSOR_ID
Shows the current SENSOR ID of the unit.
zGROUP ID
zShows the current GROUP ID of the unit.
zTEMP/VOLT1
Shows the current temperature, voltage 1 as per operating mode.
zHUMID/VOLT2
Shows the current humidity, voltage 2 as per operating mode.
< IMPORTANT >
When the unit is operated by batteries, above values are displayed for 3 seconds whenever
you press the POWER ON/OFF button.
zPOWER ON/OFF Button
To turn on the WSU, press the power button for 3 seconds until the green LED blinks twice.
To turn off the WSU, press the power button for 3 seconds until the green LED turn off.
This button operates only in battery powered mode.
zPOWER/TX Status LED
Green LED blinks whenever it transmit the data. The defaults TX interval is 15 seconds.
zPower Supply
As defaults, 2 C-size alkaline batteries are used.
GreenOK-II : Wireless Thermo-Hygro Monitor
User’s Manual (Rev 2.1)
-XW-
<Figure 3> Functional Description of Wireless Sensing Unit
<Figure 4> DIP Switches and Connectors of Wireless Sensing Unit
Table des matières
