Dacor DISTINCTIVE DRT304S Manuel technique
All specications subject to change without notice. Phone: (800) 793-0093www.dacor.com
PLANNING
GUIDE
DRT304S, DRT366S
Distinctive®30” and 36” Wide,
Slide-in Gas Rangetops
Document # PG04-003 Revised 10/17/14 Page 1/4
A
ELECTRIC CIRCUIT REQUIREMENTS
Circuit Required Total Connected Load
120 Vac 60Hz, 15 Amp. (3 wire) 1.0 Amp @ 120 Vac, 60 Hz.
GAS SUPPLY PRESSURE REQUIREMENTS*
Gas Type Manifold Pressure Minimum Gas Supply
Pressure
Natural Gas 5” Water Column 6” Water Column
Propane (LP) 10” Water Column 11” Water Column
* Maximum gas supply pressure for all models is 1/2 p.s.i.
Installation of a non-combustible material* (up to the hood) or a backsplash
is always recommended, and mandatory if the distance to the back
wall from the rangetop is less than 2 1/2” (Figure 2). When installing a
backguard, use only Dacor model number AEB3609.
SIDE VIEW WITHOUT BACKGUARD
SIDE VIEW WITHOUT BACKGUARD
SIDE VIEW
Product Dimensions
Electrical and Gas Supply Requirements
Cabinet and Countertop Layout
RANGETOP WIDTH (A)
DRT304S 29 7/8” (75.9 cm)
DRT366S 35 7/8” (91.1 cm)
Product tolerances:
±1/16” (±1.6 mm)
unless otherwise noted
WARNING
• Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.
• This appliance must be installed in accordance with the
accompanying installation instructions.
4” (10.2 cm) 5/8” (1.6 cm)
7 3/4”
(19.7 cm)
Trim:
1/2”
(1.3 cm)
thick
25 7/8” (65.7 cm)
1 5/8” (4.1 cm) cooking surface
height (grate level) above
countertop
3/4” gas inlet, connects to regulator from
bottom or rear of unit, end is recessed
2” (5.1 cm) from chassis bottom
28 1/8” (71.4 cm)
Power cord
32” (81.3 cm) long
Combustible
rear wall
Backguard mandatory if
gap from back of cooktop
to combustible wall is less
than 2 1/2”
Combustible
rear wall
2 1/2” (6.4 cm) min. to
combustible rear wall
All specications subject to change without notice. Phone: (800) 793-0093www.dacor.com
PLANNING
GUIDE
DRT304S, DRT366S
Distinctive 30” and 36” Wide,
Slide-in Gas Rangetops
Document # PG04-003 Revised 10/17/14 Page 2/4
See note 2
2See Cabinet/Countertop Dimensions - Top View
3Not applicable for cabinets more than a horizontal
distance of 10” (25.4 cm) from the edge of the rangetop.
1Vertical to combustible surface from cooktop grate level;
if installing an overhead vent hood, also check the hood
specifications for minimum required clearances.
C
13” (33.0 cm)
max.3
Top of
finished
counter
18” (45.7 cm)
min.1, 3
30” (76.2 cm)
min.1
Cutout for
utility access
Grate level
Grate
level
Recommended
gas and electrical
service location,
consult local code
B
10” (25.4 cm) to
combustible side
wall min. both sides 1/2” (1.3 cm)
overhang,
both sides
1 1/2” (3.8 cm)
typical countertop
thickness
7 3/4”
(19.7 cm)
36” (91.4 cm)
typical
Mounting platform
1” (2.5 cm) min.
thickness
Model No. B C
DRT304S 30” (76.2 cm) 30” (76.2 cm)*
36” (91.4 cm)**
DRT366S 36” (91.4 cm) 36” (91.4 cm)*
42” (106.7 cm)**
* Minimum ** Recommended
Cabinet tolerances: +1/16”, -0 (+1.6 mm, -0)
unless otherwise noted.
CABINET/COUNTERTOP DIMENSIONS - FRONT VIEW
CABINET/COUNTERTOP DIMENSIONS -
ISO VIEW
Continued. on following page...
Cabinet and Countertop Layout (continued)
All specications subject to change without notice. Phone: (800) 793-0093www.dacor.com
PLANNING
GUIDE
DRT304S, DRT366S
Distinctive 30” and 36” Wide,
Slide-in Gas Rangetops
Document # PG04-003 Revised 10/17/14 Page 3/4
CABINET/COUNTERTOP CUTOUT DIMENSIONS WITHOUT DOWNDRAFT VENT - TOP VIEW
Model No. B - Cutout Width D E
DRT304S 30” (76.2 cm) 13 3/8” (34.0 cm) 10 1/8” (25.7 cm)
DRT366S 36” (91.4 cm) 16 5/8” (42.2 cm) 11 3/16” (28.4 cm)
Cutout tolerances: +1/16” (+1.6 mm), -0, unless otherwise stated
Cabinet and Countertop Layout (continued)
Non-combustible
rear wall, rear of
mounting platform
10” (25.4 cm) min.
to combustible wall
above countertop,
both sides
Cabinet face
below countertop
overhang
Increase countertop and overhang
additional 2 1/2” (6.4 cm) min. for
combustible rear wall above
countertop
3/8” (1.3 cm)
countertop overhang
Hole 1/2” dia. (1.3 cm),
2 places, through platform
for hold down bolts
Gas/electrical utility cut-out in right rear corner of
mounting platform 8” W X 6” D (20.3 cm X 15.2 cm),
if gas and electrical are routed through bottom
1/2” (1.3 cm)
countertop
overhang
1” thick mounting platform min.
Countertop
Countertop
1/2” (1.3 cm)
countertop
overhang
2” (5.1 cm)
1” (2.5 cm)
E
24 5/8”
(62.5 cm)
D D
B
C
L
Gas connection and power cord may be
routed through bottom or back of chassis
Gas and electrical connections at
right rear section of chassis
All specications subject to change without notice. Phone: (800) 793-0093www.dacor.com
PLANNING
GUIDE
DRT304S, DRT366S
Distinctive 30” and 36” Wide,
Slide-in Gas Rangetops
Document # PG04-003 Revised 10/17/14 Page 4/4
Stiffener
Cabinet face
Control panel
Countertop
Use Dacor down-
draft vent, model
ERV3015 or
ERV3615 only IMPORTANT: See downdraft
vent installation instructions for
duct system layout/planning
DRT series rangetop
3/8” min. (1.0 cm)
space behind
downdraft vent
chassis to clear
stiffener
3/8” min. (1.0 cm)
flat countertop
overhang required
behind cutout
Minimum
countertop
height:
30 1/4"
(76.8 cm)
28 5/16” (71.9 cm)
Non combustible rear
wall recommended 10” (2.5 cm) min. to
combustible wall
above countertop,
both sides
Cabinet face
below countertop
overhang
3/8” (1.0 cm) min.
countertop overhang
2 5/8”
(6.7 cm)
Hole 1/2” dia. (1.3 cm),
2 places, through platform
for hold down bolts
1/2” (1.3 cm)
countertop
overhang
1” (2.5 cm) thick mounting platform min.
Open to below to allow for downdraft
vent, gas and electrical connections
Countertop
Countertop
1/2” (1.3 cm)
countertop
overhang
2” (5.1 cm)
1” (2.5 cm)
15”
(38.1 cm)
24 1/2”
(62.2 cm)
D
E
D
F
B
C
L
CABINET/COUNTERTOP CUTOUT
DIMENSIONS WITH DOWN-
DRAFT VENT - TOP VIEW
CABINET/COUNTERTOP CUTOUT
DIMENSIONS WITH DOWN-
DRAFT VENT - SIDE VIEW
Model No. B - Cutout
Width D E F - Vent
Cutout
DRT304S
with
ERV3015*
30”
(76.2 cm)
13 3/8”
(34.0 cm)
10 1/8”
(25.7 cm)
27 1/2” (69.9
cm)
DRT366S
with
ERV3615*
36”
(91.4 cm)
16 5/8”
(42.2 cm)
11 3/16”
(28.4 cm)
33 1/2”
(85.1 cm)
* Use only downdraft vent model specified. Downdraft vent is not
compatible with DRT rangetops having a serial number starting
with letters “SA.”
Cutout tolerances: +1/16” (+1.6 mm), -0, unless otherwise stated
Cabinet and Countertop Layout (continued)
NOTE: Gas and electrical connections may only be routed through
the bottom of the rangetop when installed with a downdraft vent.
Ce manuel convient aux modèles suivants
1
Autres manuels Dacor Gamme
Dacor
Dacor ER30D Manuel utilisateur
Dacor
Dacor Renaissance ER30G Manuel utilisateur
Dacor
Dacor DOP36T86DLS Manuel utilisateur
Dacor
Dacor DOP36P86GL Series Manuel utilisateur
Dacor
Dacor Epicure ER30G Manuel utilisateur
Dacor
Dacor Epicure 36-inch Manuel utilisateur
Dacor
Dacor Gas Range Manuel d'utilisation et d'entretien
Dacor
Dacor HGR30 Series Manuel utilisateur
Dacor
Dacor DR30DIH Manuel utilisateur
Dacor
Dacor HGPR36S Manuel utilisateur
Dacor
Dacor Millennia MRES30 Manuel utilisateur
Dacor
Dacor Professional HGR30PS Manuel utilisateur
Dacor
Dacor HGPR48S Manuel utilisateur
Dacor
Dacor HDPR36S Manuel utilisateur
Dacor
Dacor Professional HGR30P Manuel utilisateur
Dacor
Dacor Distinctive DR30E Guide rapide
Dacor
Dacor DOP36P86DL Series Manuel utilisateur
Dacor
Dacor DR30DH Manuel technique
Dacor
Dacor Epicure Range Manuel utilisateur
Dacor
Dacor ER30D Manuel utilisateur
