D-Teg BRX Series Manuel utilisateur
•Thank you for purchasing the BRX Micro DVR from D-TEG.
•Please ensure that you read and understand this USER GUIDE
and use it before connecting and installing this Recorder.
•Please store the USER GUIDE in an easily accessible location.
VER 2.1.0
USER GUIDE
Models: BRX2004A & BRX2008A
BRX
3
CAUTION
Damages due to production malfunction, loss of data, or other damages occurring
while using this product shall not be the responsibility of the manufacturer. Although
the product is a device used for recording videos, the product may not save all videos
in the case of a malfunction. In the case of an accident, the sensor may not recognize
the shock when the impact is light and as a result it may not begin recording
automatically.
SAFETY ADVICE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING:
TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
Connect your vehicle’s power cable to the product after starting the vehicle.
The instant over voltage generated when starting up the vehicle may damage
the product if it is already connected.
CAUTION
Install the product where it does not block driver’s visibility and where there is
no airbag installed. This could cause an accident or might injure the passengers in
case of accident.
Please make sure you follow the safety advice/instructions given in the user guide.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Battery for RTC(Real Time Clock) inside
4
GPS Reception
1. Activate the product in an area without large buildings to improve GPS
reception.
2. The temperature range for optimum operation of the GPS receiver in your
car is -10 ~ 50°C.
3. When using the product for the first time or after a long period (more than
three days), it may take a little longer to recognize your current location.
It may take between five and thirty minutes to get GPS reception.
GPS reception may be impaired under the following circumstances.
The commercial purpose GPS has the average range error of more than 15
meters and the range error could be more than 100 meters due to
environmental conditions like buildings, roadside trees etc.
1) If there is an object at the end of the GPS antenna
2) If your vehicle has metallic elements on the windshields
3) If equipment generating electromagnetic waves that interfere with the GPS
signal is installed in the vehicle e.g.: Other GPS devices such as a certain
type of wireless activated alarms, MP3 and CD players and camera alarms
using GPS.
4) If you are using a receiver connected by cable, electric interference can be
avoided by simply changing the location of the receiver (antenna).
5) On heavily overcast or cloudy days, if the vehicle is in a covered location
such as under a bridge or raised roadway, in a tunnel, an underground
roadway or parking area, inside a building or surrounded by high-rise
buildings.
6) If GPS signal reception is poor, it may take longer to locate your current
position when the vehicle is moving than when it is stationary.
5
CONTENTS
Each BRX2004A/2008A order includes the following items.
1. Main unit
2. GPS module with waterproof case
3. Camera input cable
4. Power cable
5. Car signal cable
6. Alarm IN/OUT, Video In/Out cable
11. Mount/ Rear Bracket
10. Keys, Screws
9. DVR Viewer CD
8. USER GUIDE
7. Mini USB Cable
6
INTRODUCTION
①
②
③
④⑤⑥⑦
⑧
⑨
①System Door Lock
②LED
[POWER] : Green LED indicates power-on
[REC] : Yellow LED indicates record-on
[ALARM] : Red LED indicates Video loss or SSD/HDD failure.
[LAN] : Yellow LED indicates network-on
③Removable HDD/SSD: Removable lock should be unlocked and Power/REC
LED should be off in order to remove the HDD/SSD.
④USB port: Ready for firmware upgrade & Upload / Download of configuration
file (set operation condition).
⑤Audio Out port
⑥Video Out Port
⑦DC 12V power Out Port : Ready for portable monitor or other electronic
devices
⑧Removable HDD/SSD Lock;
. Off → On: Turn on BRX and booting is completed in 42 seconds.
. On → Off: Turn off BRX. BRX is shut down in 15 seconds.
FRONT
7
⑨BUTTON
[SER] : Searches the recorded data.
[CH] : Changes the camera on display.
(Camera 1 → Camera 2 → Camera 3 ->.... ->Camera 8 → Camera 1)
[ESC] : Cancels or exits from the selected modes or menus.
[MENU] Enters into the menu.
[FN] : Funtion Key: used in combination with other buttons as follows;
FN + UP: Uploads the configuration file (operation settings, saved from the
DVR Viewer software through the USB memory stick.
FN + DOWN: Downloads the configuration file (operation settings) of the
current BRX to USB memory stick.
[STA] : Displays current status of BRX DVR operation.
INFORMATION: shows firmware version, GPS acceptance, Car Signal, G-
Sensor)
[Arrow/ Direction]: Moves the highlight between items in the setting menu.
Change the live display layout: Left arrow(8 channels ), Right arrow( 4
channels)
INTRODUCTION
FRONT
[Time Delay Function]
In case of Power On /Off by ACC signal in vehicle;
Time delayed start
Off → On : Starts BRX 5 seconds later and booting is completed in 47 seconds.
Time delayed shutdown
On → Off : Stops recording immediately (record LED off) and shutdown takes
75 seconds till completed (power LED off)
8
INTRODUCTION
REAR
①②③④
⑤⑥⑦⑧⑨⑩
①Power Connector
Battery : Connects to the battery power in vehicle.
ACC : Connects to the ignition power in vehicle.
②Car Signal Connector: left/right signals, brake, reverse, speed pulse signal
③Serial Port
S1 : For trouble shooting (debugging) purpose
S2(T) : Ready for interface to additional device
S3 : Connect the provided GPS
④Main power Switch
⑤Power out: Ready for portable monitor or other device (DC 12V OUT)
⑥DIGITAL IO / AV OUT
Alarm in; 8 ports
Alarm Out: 2 ports
Video / Audio Out
⑦AV In (1~4)
For camera 1 ~ 4 (Video, Audio signal & power supply to camera (12V)
⑧AV In (5~8)
For camera 5 ~ 8 (Video, Audio signal & power supply to camera (12V)
⑨USB: firmware upgrade & Upload / Download of configuration file (set operation
condition).
⑩LAN
9
CONNECTION DIAGRAM
10
POWER ON
Main power switch
1. TURNING ON THE POWER
① Make sure that peripherals are properly connected.
② Switch「ON」the main power switch on the rear panel as below,
③ Turn on the Removable HDD/SSD lock using key from [OFF] to [ON] as below,
The front POWER LED will light up in green. Please wait approximately 42 seconds
until it start recording up. The recording will automatically begin just power on.
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels D-Teg DVR
