CyberData VoIP V2 Manuel utilisateur

Quick Start Guide 930398E

The IP Endpoint Company

1.0 Out-of-Box and Prior to Final Installation

1.1. Verify that you have received all of the parts listed on the Installation Quick

Reference placemat.

1.2. Download the current manual, otherwise known as an Operation Guide,

which is available on the Documentation page at the following website

address:

http://www.cyberdata.net/products/voip/digitalanalog/ceilingspkr2/docs.html

Note You can also navigate to the Documentation page by going to

www.CyberData.net and following the steps that are indicated by

the following figures:

2.0 Select Power Source

PoE Switch PoE Injector

Set PoE power type to Class 0 = 15.4W CAT6 cable recommended—

for longer distances

Be sure you are using a non-PoE switch or port

Make sure port is not in trunk mode

Set port to full duplex/ 100mbps

Spanning Tree Protocol (STP) must be disabled or Portfast enabled

VoIP V2 Ceiling Speaker

Quick Start Guide

Quick Start Guide 930398E

3.0 Power Test

3.1. Plug in the CyberData device and monitor the LED activity on the front of

the device. See the following figure:

3.2. The GREEN power/status LED and the YELLOW network LED come on

immediately. The YELLOW network LED will blink to indicate network

traffic. After about 27 seconds, the GREEN power/status LED will blink

twice to indicate that the board is fully booted.

If there is no DHCP server available on the network, it will try 12 times with

a three second delay between tries and eventually fall back to the

programmed static IP address (by default 10.10.10.10). This process will

take approximately 80 seconds.

3.3. When the device has completed the initialization process, press and hold the

RTFM switch for 3 seconds to announce the IP address.

This concludes the power test. Go to Section 4.0, "Connecting to a Network

in a Test Environment".

Speaker

Status

(Green LED)

Network

Link/Activity

(Yellow LED)

Quick Start Guide 930398E

4.0 Connecting to a Network in a Test Environment

Note The following connections are usually needed for this procedure:

•PC

• PoE switch or injector

•CyberDatadevice

4.1. In a test environment, use a PC that is connected to the same switch as a

single CyberData device. Note the subnet of the test PC.

4.2. Use the CyberData Discovery Utility program to locate the device on the

network. You can download the Discovery Utility program from the

following website address:

http://www.cyberdata.net/support/voip/discovery_utility.html

4.3. Wait for initialization to complete before using the Discovery Utility

program to scan for a device. The device will show the current IP address,

MAC address, and serial number.

4.4. Select the device.

Note If the IP address of the device is in the same subnet of the PC, then

go to Step 4.7.

4.5. If the IP address of the device is different from the subnet of the PC, then

complete the following steps:

4.5.1. Click the Details tab.

4.5.2. Click Adv. Config to manually configure settings with an available IP

address in the same subnet.

Note A gateway address of 0.0.0.0 or a subnet address of

255.255.255.255 will prompt you to enter a valid address.

4.5.3. Click OK after you are finished making changes.

4.6. A dialog box will prompt you to click OK after confirming the configuration

changes and will ask you to wait while the device reboots. Please wait for

the device to power up and wait for the Discovery Utility program to find

the device on the network.

Quick Start Guide 930398E

4.7. After the Discovery Utility program has located the device on the network,

click Launch Browser . When the IP address matches the subnet of the PC

that you are using to access the device, the Discovery Utility program will

be able to launch the browser window which is configured to the device’s IP

address.

4.8. Log on to the web interface by using the default username (admin) and

password (admin) to configure the device.

4.9. Perform an audio test by pressing the Te st A ud i o button that is located at

the bottom of the Device Configuration page. If the audio test message is

clearly audible, then your CyberData device is functioning properly.

4.10. The device is now ready to be set for your desired network configuration.

You may reference our IP-PBX specific configurations at the following

website address:

http://www.cyberdata.net/support/server/index.html

5.0 Contacting CyberData VoIP Technical Support

For quality assurance purposes, we ask that you please visit our website and

complete our Support form which is available at the following website address:

http://www.cyberdata.net/support/contactsupportvoip.html

Note You can also navigate through menus to the Support form by going to

www.CyberData.net as shown in the following figure:

The Support form initiates a ticket which CyberData uses for tracking customer

requests. Most importantly, the Support form tells us which PBX system and

software version that you are using, the make and model of the switch, and other

important information. This information is essential for troubleshooting. Please

also include as much detail as possible in the Comments section of the Support

form.

Requests for Returned Materials Authorization (RMA) numbers require an active

VoIP Technical Support ticket number. A product will not be accepted for return

without an approved RMA number.

Autres manuels pour VoIP V2

Table des matières

Autres manuels CyberData Intervenants

CyberData

CyberData 011402 Manuel

CyberData

CyberData 11098 Manuel utilisateur

CyberData

CyberData 011589 Manuel

CyberData

CyberData 011458 Manuel

CyberData

CyberData 11065 Manuel utilisateur

CyberData

CyberData 011395 Manuel utilisateur

CyberData

CyberData 011505 Manuel

CyberData

CyberData 011393 SERIES Manuel utilisateur

CyberData

CyberData 011504 Manuel

CyberData

CyberData 011487 Manuel

CyberData

CyberData 11021 Manuel utilisateur

CyberData

CyberData 011098B Manuel utilisateur

CyberData

CyberData 011505 Manuel utilisateur

CyberData

CyberData VoIP Ceiling Speaker Manuel utilisateur

CyberData

CyberData 011405 Manuel utilisateur

CyberData

CyberData 011216 Manuel

CyberData

CyberData 11021 Manuel utilisateur

CyberData

CyberData TN083 Manuel utilisateur

CyberData

CyberData 011504 Manuel

CyberData

CyberData 011072 Manuel

CyberData

CyberData Alteva Manuel utilisateur

CyberData

CyberData 011397 Manuel utilisateur

CyberData

CyberData 011504 Manuel utilisateur

CyberData

CyberData 10844 Manuel utilisateur

Manuels Intervenants populaires d'autres marques

argon audio

argon audio IE20 Manuel utilisateur

Denon

Denon SC-N7 Manuel utilisateur

Gemline

Gemline Ace 3952 Manuel utilisateur

Focal

Focal ON WALL 300 Mode d’emploi

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuel utilisateur

SoundLogic

SoundLogic BCCS-6/6395 Manuel utilisateur

Peavey

Peavey DTH 218 Manuel utilisateur

Avantree

Avantree Pluto Air Manuel utilisateur

Morel

Morel Integra Series INTEGRA OVATION 4 Manuel utilisateur

Oppo

Oppo SONICA Manuel utilisateur

Bose

Bose SoundLink Wireless Music System Manuel utilisateur

Rocksteady

Rocksteady Stadium Manuel utilisateur

Bowers & Wilkins

Bowers & Wilkins 4 Manuel utilisateur

Sonance

Sonance SONOS OUTDOOR Series Manuel utilisateur

Electro-Voice

Electro-Voice EVID FM4.2 Manuel utilisateur

Pioneer

Pioneer XW-HTD630 Manuel utilisateur

Onn

Onn BWA16AA002 Manuel utilisateur

HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur