CyberData 11233 Manuel utilisateur

Quick Start Guide 931086B

The IP Endpoint Company

1.0 Out-of-Box and Prior to Final Installation

1.1. Verify that you have received all of the parts listed on the Installation Quick

Reference placemat.

1.2. Download the current manual, otherwise known as an Operation Guide,

which is available on the Documentation page at the following website

address:

http://www.cyberdata.net/voip/011233/

Note You can also navigate to the Documentation page by going to

www.CyberData.net and following the steps that are indicated by

the following figures:

2.0 Select Power Source

PoE Switch PoE Injector

Set PoE power type to Class 0 = 15.4W CAT6 cable recommended—

for longer distances

Be sure you are using a non-PoE switch or port

Make sure port is not in trunk mode

Set port to full duplex/ 100mbps

Spanning Tree Protocol (STP) must be disabled or Portfast enabled

Part Number: 011233

SIP Paging Adapter

Quick Start Guide

Quick Start Guide 931086B

3.0 Power Test

3.1. Plug in the CyberData device and monitor the LED activity on the front of

the device. See the following figure:

3.2. The GREEN/BLUE Status LED and the GREEN Paging LED both blink at a

rate of 10 times per second during the initial network setup.

The round, GREEN/BLUE Status LED on the front of the Paging Server

comes on indicating that the power is on. Once the device has been

initialized, this LED blinks at one second intervals.

The square, GREEN/AMBER Link LED above the Ethernet port indicates

that the network connection has been established. The Link LED changes

color to confirm the auto-negotiated connection speed:

• The Link LED is GREEN at 10 Mbps.

• The Link LED is AMBER at 100 Mbps.

The GREEN Paging LED comes on while the device is booting and turns off

after 15 seconds. This light blinks when a page is in progress. You can disable

Beep on Initialization on the Device Configuration page.

The square, GREEN Activity LED blinks when there is network traffic.

If there is no DHCP server available on the network, it will try 12 times with a

three second delay between tries and eventually fall back to the

programmed static IP address (by default 10.10.10.10). This process will

take approximately 80 seconds.

3.3. When the device has completed the initialization process, briefly press and

then quickly release the RTFM switch to announce the IP address.

This concludes the power test. Go to Section 4.0, "Connecting to a Network

in a Test Environment".

Status

(GREEN/BLUE LED)

Paging

(GREEN LED)

Link

(GREEN/AMBER LED)

Activity

(GREEN LED)

Quick Start Guide 931086B

4.0 Connecting to a Network in a Test Environment

Note The following connections are usually needed for this procedure:

• Computer

• PoE switch or injector

• CyberData device

4.1. In a test environment, use a computer that is connected to the same switch

as a single CyberData device. Note the subnet of the test computer.

4.2. Use the CyberData Discovery Utility program to locate the device on the

network. You can download the Discovery Utility program from the following

website address:

http://www.cyberdata.net/assets/common/discovery.zip

4.3. Wait for initialization to complete before using the Discovery Utility program

to scan for a device. The device will show the current IP address, MAC

address, and serial number.

4.4. Select the device.

4.5. Click Launch Browser. If the IP address is in a reachable subnet from the

computer that you are using to access the device, the Discovery Utility

program should be able to launch the browser window which is configured

to the device’s IP address.

4.6. Log on to the web interface by using the default username (admin) and

password (admin) to configure the device.

4.7. The device is now ready to be set for your desired network configuration.

You may reference our IP-PBX specific configurations at the following

website address:

http://www.cyberdata.net/connecting-to-ip-pbx-servers/

Quick Start Guide 931086B

5.0 Contacting CyberData VoIP Technical Support

We encourage you to access our Technical Support help desk at the following

address:

http://support.cyberdata.net/

Note You can also access the Technical Support help desk by navigating through

menus on the CyberData website (www.CyberData.net) as shown in the

following figure:

The Technical Support help desk provides the options of accessing

documentation for your CyberData product, browsing the knowledge base, and

submitting a troubleshooting ticket.

Please be advised requests for Returned Materials Authorization (RMA) numbers

require an active VoIP Technical Support ticket number. A product will not be

accepted for return without an approved RMA number.

Autres manuels pour 11233

Table des matières

Autres manuels CyberData Adaptateur

CyberData

CyberData Singlewire Paging Adapter Manuel d'instructions

CyberData

CyberData 11233 Manuel utilisateur

CyberData

CyberData 11280 Manuel

CyberData

CyberData Singlewire Paging Adapter Guide de démarrage rapide

CyberData

CyberData VoIP V2 Manuel utilisateur

CyberData

CyberData 11280 Manuel utilisateur

CyberData

CyberData 11107 Manuel

CyberData

CyberData 11233 Manuel utilisateur

CyberData

CyberData 11024 Manuel utilisateur

CyberData

CyberData 011280C Manuel utilisateur

CyberData

CyberData SIP PAGING ADAPTER Guide de démarrage rapide

CyberData

CyberData Singlewire Paging Adapter Manuel d'instructions

CyberData

CyberData SIP PAGING ADAPTER Manuel d'instructions

CyberData

CyberData 11280 Manuel utilisateur

CyberData

CyberData 11233 Manuel

CyberData

CyberData 11233 Manuel utilisateur

CyberData

CyberData VoIP V2 Manuel utilisateur

CyberData

CyberData 11233 Manuel

Manuels Adaptateur populaires d'autres marques

PCB Piezotronics

PCB Piezotronics 090B274 Manuel utilisateur

Auvidea

Auvidea J20 Manuel du produit

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuel utilisateur

Akribis

Akribis ITF-21-BISS-MIT Manuel utilisateur

Tenda

Tenda W54U Manuel utilisateur

ROHO

ROHO AGILITY Manuel utilisateur

PROLiNK

PROLiNK WN2001 Manuel utilisateur

Hawking

Hawking HUF2 Manuel utilisateur

Airlink101

Airlink101 AWLC4030 Manuel utilisateur

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuel utilisateur

Philips

Philips SWA4554S/10 Manuel utilisateur

JVC

JVC TS-C9D2B Manuel d'instructions

NETGEAR

NETGEAR A6100 Manuel utilisateur

D-Link

D-Link DWA-121 Manuel utilisateur

Philips

Philips SWA2037 Manuel utilisateur

Basalte

Basalte 0610-20 Manuel utilisateur

Yealink

Yealink EHS40 Manuel utilisateur

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuel utilisateur