Curtis PL4210A-2 Manuel utilisateur
Contents
Introduction
Warning
Caution
Main Unit Description
Remote Control
OSD basic adjustment
Specification
Trouble Shooting
1
Introduction
Thank you very much for your purchase of our product of PDP TV. It serves as a
normal color TV and PC monitor. To enjoy your TV to the full from the very beginning,
read this manual carefully and keep it handy for ready reference.
INSTALLATION
ķ
Locate the TV in a room where direct light does not strike the screen. Total darkness or
a reflection on the picture screen can cause eyestrain. Soft and indirect lighting is
recommended for comfortable viewing.
ĸ
Allow enough space between the receiver and the wall to permit ventilation.
Ĺ
Avoid excessively warm locations to prevent possible damage to the cabinet or
premature component failure.
ĺ
This TV can be connected to AC100-240V~ 50/60HZ.
Ļ
Do not install the TV in a location near heat sources such as radiator, air ducts, direct
sunlight, or in a place somewhere like close compartment and close area. Do not cover
the ventilation openings when using the TV.
ļ
The indicator light will last about 30 seconds to go out after cutting off the electricity,
during this period, you cannot repower it on until the indicator light goes out, thanks a
lot for your attention!
2
Warning
CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER- SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol is intended to alert the user to avoid the risk
of electric shock, do not disassemble this equipment by
anyone except a qualified service personnel.
This symbol is intended to alert the user to the presence
of important operation and maintenance instructions in
the literature accompanying the equipment.
3
4
Caution
Caution
High voltages are used in the operation of this product.
- Donot
open the product's casing. Refer servicing
to qualified service personnel .
Caution
To prevent fire or electrical shock hazard, Do not expose
the main unit to moisture.
Caution
Do not drop or push objects into the television cabinet
slots or openings. Never spill any kind of liquid on the
television receiver.
Caution
Avoid exposing the main unit to direct sunlight and other
sources of heat. Do not stand the television receiver
directly on other products which give off heat. E. g. video
cassette players, Audio amplifiers. Do not block the
ventilation holes in the back cover. Ventilation is essential
to prevent failure of electrical component. Do not squash
power supply cord under the main
unit or other heavy objects.
Caution
Caution
Never stand on, lean on, push suddenly the product
or its stand. You should Pay special attention to
children.
Caution
Do not place the main unit on an unstable cart stand,
shelf or table. Serious injury to an individual, and
damage to the television, may result if it should fall.
Caution
When the product is not used for an extended period
of time, it is advisable to disconnect the AC power
cord from the AC outlet.
Caution
The PDP panel used in this product is made of glass.
Therefore, it can break when the product is dropped
or applied with impact. Be careful not to be injured
by broken glass pieces in case the PDP panel breaks.
5
Main unit description
Control Panel Button Function
VOL+ : Volume up.
VOL- : Volume down.
CH+: TV channel up.
CH- : TV channel down.
MENU : Press to select the main menu.
TV/AV : Select the input signal.
POWER : Switch on when in standby mode or enter the standby mode.
TV Terminal Connections
1. HDMI1 input terminal.
2. HDMI2 input terminal.
3. HDMI3 input terminal.
4. VGA input terminal.
5. PC audio input terminal.
6. VIDEO2 input terminal.
7. AUDIO2 input terminal.
8. Component input terminal.
9. VIDEO1 input terminal.
10. AUDIO1 input terminal.
11. TV antenna
12. USB input terminal˄RQO\IRUXSJUDGHVRIW˅
Power Input Configuration
AC POWER
6
Locations of wall mout, power and terminals
NOTE
●The TV dose not support wake sleep
●It supports must more than 2 GB It supports FAT/FAT32 document. The max FAT
document is 4GB and the max FAT32 document is 2TB.
7
Remote control
POWER: Power on/off button, press once to turn the TV on and
press again to turn the TV off.
MUTE: Press this button to mute or restore sound.
FREEZE˖Press this key to hold the picture
SLEEP: Set the sleep timer.
ASPECT: Press to adjust picture ratio.
EPG˖Enter electronic program guide
CC: Press this key to select the CC Mode. Three CC Mode are
available including On, CC on mute and off
AUTO: Adjust the picture automatically in pc mode.
PMODE: Select picture mode.
SMODE: Select sound mode.
MTS/AUDIO: When stereo program is received, press this key to
switch sound system between mono and stereo.
When SAP program is received, press this button to switch
sound system between mono and SAP
When stereo and SAP program is received, press this key to
switch among mono, stereo and SAP.
Press this key to show the list of audio languages available for
the current channel in ATSC
SOURCE: Press to change signal source.
MENU: Press this button to enter the main menu.
EXIT: Exit the OSD (On-screen display).
ENTER: Enter the selected option or perform the selected
operation.
0-9: Select and switch to a channel using 0 - 9.
-/--: Switch the program digit.
:Switch back and front between the current and previous channels.
CH+/CH-: Change the channel.
VOL+/VOL-: Adjust the volume.
INFO: Display some information of current program in TV mode.
FAV: Switch between custom set " Favorite List"
F.LIST: Switch between custom set "Favorite List"
C.LIST: Press this key to display the channel list in TV mode
8
OSD basic adjustment
Installation Guide
. Press MENU button to display the MAIN OSD MENU;
.Press ◄/ ►button to select the MENU you want;Press ENTER button to enter the sub menu;
.Press ▼/ ▲button to select the option and then press ◄/ ►to adjust the value in the sub
menu;
.You can press MENU button to go back to the upper menu or EXIT button to close the OSD.
PICTURE
Press ENTER when the Picture Settings item is highlighted. Then you will go to the
sub-menu as following.
Press ▼/ ▲to select the desired menu item. Press ENTER to proceed if necessary.
Press ◄/ ►to to adjust the item the desired level.
When you have changed the settings, you can exit from the menu by pressing MENU.
9
Table des matières
Langues :
Autres manuels Curtis Téléviseur à écran plat
