Current COMPASS CELS Manuel utilisateur

WARNING – This product contains chemicals known to the State of California to cause cancer, birth

defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning,

or otherwise touching this product.

Surface Mount LED Emergency Exit

CELS

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should

always be followed including the following:

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS

1. Do not use outdoors.

2. Do not let power supply cords touch hot surfaces.

3. Do not mount near gas or electric heaters.

4. Equipment should be mounted in locations and at heights where it will not readily be subject

to tampering by unauthorized personnel.

5. The use of accessory equipment not authorized by the manufacturer may cause an unsafe

condition.

6. Do not use this equipment for other than its intended purpose.

7. Servicing of this equipment should be performed by qualiﬁed service personnel.

8. Test cycling: the Life Safety Code (NFPA 101) requires testing of emergency lighting units once

a month for a minimum of 30 seconds, and once a year for a minimum of 90 minutes.

INSTALLER:

•SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS

•SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT

RECYCLING INFORMATION

All steel, aluminum and thermoplastic parts are recyclable.

NOTICE: Emergency units contain rechargeable batteries which must

be recycled or disposed of properly.

PACKAGE CONTENTS

Part Description Quantity

1 LED Edge-Lit EXIT Sign 1

2 Canopy 1

3 Hardware Bag 1

ELECTRICAL CONNECTIONS

1. Make the proper supply wire connections.

2. If using 120 VAC, connect the black and white wires to the building utility.

3. If using 277 VAC, connect the orange and white wires to the building utility.

4. Cap o unused wire. In all cases, use standard wire nuts in connection to wires.

WIRING DIAGRAM

Hubbell Lighting, Inc.

WARNING – This product contains chemicals known to the State of California to cause cancer, birth

defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning,

or otherwise touching this product.

Surface Mount LED Emergency Exit

CELS

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should

always be followed including the following.

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS

1. Do not use outdoors.

2. Do not let power supply cords touch hot surfaces.

3. Do not mount near gas or electric heaters.

4. Equipment should be mounted in locations and at heights where it will not readily be subject

to tampering by unauthorized personnel.

5. The use of accessory equipment not authorized by the manufacturer may cause an

unsafe condition.

6. Do not use this equipment for other than its intended purpose.

7. Servicing of this equipment should be performed by qualified service personnel.

8. Test cycling: the Life Safety Code (NFPA 101) requires testing of emergency lighting units once a month for a

minimum of 30 seconds, and once a year for a minimum of 90 minutes.

INSTALLER:

•SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS

•SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT

RECYCLING INFORMATION

All steel, aluminum and thermoplastic parts are recyclable.

NOTICE: Emergency units contain rechargeable batteries which

must be recycled or disposed of properly.

Hubbell Lighting, Inc. Life Safety Products • www.dual-lite.com

COMP0002_INST_SHT 09/12

PACKAGE CONTENTS

Part Description Quantity

1 LED Edge-Lit EXIT Sign 1

2 Canopy 1

3 Hardware Bag 1

ELECTRICAL CONNECTIONS

1. Make the proper supply wire connections.

2. If using 120 VAC, connect the black and white wires to the building utility.

3. If using 277 VAC, connect the orange and white wires to the building utility.

4. Cap off unused wire. In all cases, use standard wire nuts in connection to wires.

WIRING DIAGRAM

COMP0002

Rev 06/08/22

comp_cels_instsht_R01

currentlighting.com/compass

without notice. All values are design or typical values when measured under laboratory conditions.

Current Lighting Solutions, LLC

701 Millennium Blvd.

Greenville, SC 29607

INSTALLATION INSTALLATION

1. Attach crossbar to junction box,

using screws if needed

(screws are not provided)

2. Use screwdriver to open front cover

to connect battery connector.

6. Peel o protective ﬁlm from both sides of EXIT panel

Insert EXIT panel into main body assembly gently. If EXIT panel is for single

face, make sure EXIT letter direction is correct.

3. Feed AC supply wires through canopy

center hole.

4. Assemble canopy onto main

body assembly with (2) PM4*15

screws (supplied) and make wire

connections.

(See ELECTRICAL CONNECTIONS)

5. Use (2) PM4-40 screws (supplied)

tighten canopy to crossbar.

7. Determine direction for

chevron placement.

(See DETERMINE DIRECTION)

8. The unit can be installed on any

surface. You may rotate the EXIT

panel in any angle from 0° to 180°.

Ceiling mounting rotate 90°

become wall mounting.

NOTE: FIRST TURN OFF ELECTRICITY

SURFACE CEILING & WALL MOUNTING

SURFACE END MOUNTING

1. Attach crossbar to junction box,

using screws if needed.

(Screws are not provided)

2. Use screwdriver open front cover

to connect battery connector.

3. Remove the hole plug from

mounting end cap.

4. Pull out all AC supply wires and

feed wires thru the center hole of

mounting end cap and then canopy.

5. Reference 4-7 step in surface

ceiling and wall mounting above

for surface end mounting.

6. The unit can be installed on any

surface, you may rotate the EXIT

panel in any angle from 0° to 180°.

ASSEMBLY DRAWING

DETERMINE DIRECTIONS

1. If indicator chevron is required,

maintain chevron and remove

locator template.

2. If indicator chevron is not required,

remove both the chevron and

locator template.

INSTALLATION INSTALLATION

1. Attach crossbar to junction box, using screws

if needed (screws are not provided)

2. Use screwdriver to open front cover to

connect battery connector.

6. Insert EXIT panel into main body assembly

gently. If EXIT panel is for single face, make

sure EXIT letter direction is correct.

3. Feed AC supply wires through canopy center hole.

4. Assemble canopy onto main body assembly

with (2) PM4*15 screws (supplied) and make

wire connections.

(See ELECTRICAL CONNECTIONS)

5. Use (2) PM4-40 screws (supplied) tighten

canopy to crossbar.

7. Determine direction for chevron placement.

(See DETERMINE DIRECTION)

8. The unit can be installed on any surface.

You may rotate the EXIT panel in any angle

from 0° to 180°. Ceiling mounting rotate 90°

become wall mounting.

NOTE: FIRST TURN OF ELECTRICITY

SURFACE CEILING & WALL MOUNTING

SURFACE END MOUNTING

1. Attach crossbar to junction box, using screws

if needed. (Screws are not provided)

2. Use screwdriver open front cover to connect

battery connector.

3. Remove the hole plug from mounting end cap.

4. Pull out all AC supply wires and feed wires

thru the center hole of mounting end cap and

then canopy.

5. Reference 4-7 step in surface ceiling and wall

mounting above for surface end mounting.

6. The unit can be installed on any surface, you

may rotate the EXIT panel in any angle from

0° to 180°.

ASSEMBLY DRAWING

DETERMINE DIRECTIONS

1. If indicator chevron is required, maintain

chevron and remove locator template.

2. If indicator chevron is not required, remove

both the chevron and locator template.

INSTALLATION INSTALLATION

1. Attach crossbar to junction box, using screws

if needed (screws are not provided)

2. Use screwdriver to open front cover to

connect battery connector.

6. Insert EXIT panel into main body assembly

gently. If EXIT panel is for single face, make

sure EXIT letter direction is correct.

3. Feed AC supply wires through canopy center hole.

4. Assemble canopy onto main body assembly

with (2) PM4*15 screws (supplied) and make

wire connections.

(See ELECTRICAL CONNECTIONS)

5. Use (2) PM4-40 screws (supplied) tighten

canopy to crossbar.

7. Determine direction for chevron placement.

(See DETERMINE DIRECTION)

8. The unit can be installed on any surface.

You may rotate the EXIT panel in any angle

from 0° to 180°. Ceiling mounting rotate 90°

become wall mounting.

NOTE: FIRST TURN OF ELECTRICITY

SURFACE CEILING & WALL MOUNTING

SURFACE END MOUNTING

1. Attach crossbar to junction box, using screws

if needed. (Screws are not provided)

2. Use screwdriver open front cover to connect

battery connector.

3. Remove the hole plug from mounting end cap.

4. Pull out all AC supply wires and feed wires

thru the center hole of mounting end cap and

then canopy.

5. Reference 4-7 step in surface ceiling and wall

mounting above for surface end mounting.

6. The unit can be installed on any surface, you

may rotate the EXIT panel in any angle from

0° to 180°.

ASSEMBLY DRAWING

DETERMINE DIRECTIONS

1. If indicator chevron is required, maintain

chevron and remove locator template.

2. If indicator chevron is not required, remove

both the chevron and locator template.

INSTALLATION INSTALLATION

1. Attach crossbar to junction box, using screws

if needed (screws are not provided)

2. Use screwdriver to open front cover to

connect battery connector.

6. Insert EXIT panel into main body assembly

gently. If EXIT panel is for single face, make

sure EXIT letter direction is correct.

3. Feed AC supply wires through canopy center hole.

4. Assemble canopy onto main body assembly

with (2) PM4*15 screws (supplied) and make

wire connections.

(See ELECTRICAL CONNECTIONS)

5. Use (2) PM4-40 screws (supplied) tighten

canopy to crossbar.

7. Determine direction for chevron placement.

(See DETERMINE DIRECTION)

8. The unit can be installed on any surface.

You may rotate the EXIT panel in any angle

from 0° to 180°. Ceiling mounting rotate 90°

become wall mounting.

NOTE: FIRST TURN OF ELECTRICITY

SURFACE CEILING & WALL MOUNTING

SURFACE END MOUNTING

1. Attach crossbar to junction box, using screws

if needed. (Screws are not provided)

2. Use screwdriver open front cover to connect

battery connector.

3. Remove the hole plug from mounting end cap.

4. Pull out all AC supply wires and feed wires

thru the center hole of mounting end cap and

then canopy.

5. Reference 4-7 step in surface ceiling and wall

mounting above for surface end mounting.

6. The unit can be installed on any surface, you

may rotate the EXIT panel in any angle from

0° to 180°.

ASSEMBLY DRAWING

DETERMINE DIRECTIONS

1. If indicator chevron is required, maintain

chevron and remove locator template.

2. If indicator chevron is not required, remove

both the chevron and locator template.

INSTALLATION INSTALLATION

1. Attach crossbar to junction box, using screws

if needed (screws are not provided)

2. Use screwdriver to open front cover to

connect battery connector.

6. Insert EXIT panel into main body assembly

gently. If EXIT panel is for single face, make

sure EXIT letter direction is correct.

3. Feed AC supply wires through canopy center hole.

4. Assemble canopy onto main body assembly

with (2) PM4*15 screws (supplied) and make

wire connections.

(See ELECTRICAL CONNECTIONS)

5. Use (2) PM4-40 screws (supplied) tighten

canopy to crossbar.

7. Determine direction for chevron placement.

(See DETERMINE DIRECTION)

8. The unit can be installed on any surface.

You may rotate the EXIT panel in any angle

from 0° to 180°. Ceiling mounting rotate 90°

become wall mounting.

NOTE: FIRST TURN OF ELECTRICITY

SURFACE CEILING & WALL MOUNTING

SURFACE END MOUNTING

1. Attach crossbar to junction box, using screws

if needed. (Screws are not provided)

2. Use screwdriver open front cover to connect

battery connector.

3. Remove the hole plug from mounting end cap.

4. Pull out all AC supply wires and feed wires

thru the center hole of mounting end cap and

then canopy.

5. Reference 4-7 step in surface ceiling and wall

mounting above for surface end mounting.

6. The unit can be installed on any surface, you

may rotate the EXIT panel in any angle from

0° to 180°.

ASSEMBLY DRAWING

DETERMINE DIRECTIONS

1. If indicator chevron is required, maintain

chevron and remove locator template.

2. If indicator chevron is not required, remove

both the chevron and locator template.

INSTALLATION INSTALLATION

1. Attach crossbar to junction box, using screws

if needed (screws are not provided)

2. Use screwdriver to open front cover to

connect battery connector.

6. Insert EXIT panel into main body assembly

gently. If EXIT panel is for single face, make

sure EXIT letter direction is correct.

3. Feed AC supply wires through canopy center hole.

4. Assemble canopy onto main body assembly

with (2) PM4*15 screws (supplied) and make

wire connections.

(See ELECTRICAL CONNECTIONS)

5. Use (2) PM4-40 screws (supplied) tighten

canopy to crossbar.

7. Determine direction for chevron placement.

(See DETERMINE DIRECTION)

8. The unit can be installed on any surface.

You may rotate the EXIT panel in any angle

from 0° to 180°. Ceiling mounting rotate 90°

become wall mounting.

NOTE: FIRST TURN OF ELECTRICITY

SURFACE CEILING & WALL MOUNTING

SURFACE END MOUNTING

1. Attach crossbar to junction box, using screws

if needed. (Screws are not provided)

2. Use screwdriver open front cover to connect

battery connector.

3. Remove the hole plug from mounting end cap.

4. Pull out all AC supply wires and feed wires

thru the center hole of mounting end cap and

then canopy.

5. Reference 4-7 step in surface ceiling and wall

mounting above for surface end mounting.

6. The unit can be installed on any surface, you

may rotate the EXIT panel in any angle from

0° to 180°.

ASSEMBLY DRAWING

DETERMINE DIRECTIONS

1. If indicator chevron is required, maintain

chevron and remove locator template.

2. If indicator chevron is not required, remove

both the chevron and locator template.

INSTALLATION INSTALLATION

1. Attach crossbar to junction box, using screws

if needed (screws are not provided)

2. Use screwdriver to open front cover to

connect battery connector.

6. Insert EXIT panel into main body assembly

gently. If EXIT panel is for single face, make

sure EXIT letter direction is correct.

3. Feed AC supply wires through canopy center hole.

4. Assemble canopy onto main body assembly

with (2) PM4*15 screws (supplied) and make

wire connections.

(See ELECTRICAL CONNECTIONS)

5. Use (2) PM4-40 screws (supplied) tighten

canopy to crossbar.

7. Determine direction for chevron placement.

(See DETERMINE DIRECTION)

8. The unit can be installed on any surface.

You may rotate the EXIT panel in any angle

from 0° to 180°. Ceiling mounting rotate 90°

become wall mounting.

NOTE: FIRST TURN OF ELECTRICITY

SURFACE CEILING & WALL MOUNTING

SURFACE END MOUNTING

1. Attach crossbar to junction box, using screws

if needed. (Screws are not provided)

2. Use screwdriver open front cover to connect

battery connector.

3. Remove the hole plug from mounting end cap.

4. Pull out all AC supply wires and feed wires

thru the center hole of mounting end cap and

then canopy.

5. Reference 4-7 step in surface ceiling and wall

mounting above for surface end mounting.

6. The unit can be installed on any surface, you

may rotate the EXIT panel in any angle from

0° to 180°.

ASSEMBLY DRAWING

DETERMINE DIRECTIONS

1. If indicator chevron is required, maintain

chevron and remove locator template.

2. If indicator chevron is not required, remove

both the chevron and locator template.

INSTALLATION INSTALLATION

1. Attach crossbar to junction box, using screws

if needed (screws are not provided)

2. Use screwdriver to open front cover to

connect battery connector.

6. Insert EXIT panel into main body assembly

gently. If EXIT panel is for single face, make

sure EXIT letter direction is correct.

3. Feed AC supply wires through canopy center hole.

4. Assemble canopy onto main body assembly

with (2) PM4*15 screws (supplied) and make

wire connections.

(See ELECTRICAL CONNECTIONS)

5. Use (2) PM4-40 screws (supplied) tighten

canopy to crossbar.

7. Determine direction for chevron placement.

(See DETERMINE DIRECTION)

8. The unit can be installed on any surface.

You may rotate the EXIT panel in any angle

from 0° to 180°. Ceiling mounting rotate 90°

become wall mounting.

NOTE: FIRST TURN OF ELECTRICITY

SURFACE CEILING & WALL MOUNTING

SURFACE END MOUNTING

1. Attach crossbar to junction box, using screws

if needed. (Screws are not provided)

2. Use screwdriver open front cover to connect

battery connector.

3. Remove the hole plug from mounting end cap.

4. Pull out all AC supply wires and feed wires

thru the center hole of mounting end cap and

then canopy.

5. Reference 4-7 step in surface ceiling and wall

mounting above for surface end mounting.

6. The unit can be installed on any surface, you

may rotate the EXIT panel in any angle from

0° to 180°.

ASSEMBLY DRAWING

DETERMINE DIRECTIONS

1. If indicator chevron is required, maintain

chevron and remove locator template.

2. If indicator chevron is not required, remove

both the chevron and locator template.

Ce manuel convient aux modèles suivants

Autres manuels Current Moniteur

Current

Current Dual-Lite LED1EM Mode d'emploi

Current

Current COMPASS tradeselect CE Manuel utilisateur

Current

Current COMPASS tradeselect CCRGRC Manuel utilisateur

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Furuno

Furuno Mu 120c Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

LG 50PM1M - - 50" Plasma Panel Manuel utilisateur

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

NEC

NEC AccuSync LCD5V Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation