CUMMINS ALLISON JetScan MPX 8200 Manuel utilisateur
|
| 1
Getting started
JetScan®MPX 8200
Automatic-strapping module
and corner module
User guide
Table of Contents
Safety information, power specications ................................................................. 2
About this guide .................................................................................................... 3
Strapping module diagram ..................................................................................... 4
Corner module diagram ......................................................................................... 6
Maintaining bins.................................................................................................... 7
Maintaining paper rolls .......................................................................................... 8
Maintaining printer ribbon cartridge ...................................................................... 10
Conguring strap length and printing .................................................................... 11
Stopping conditions and recovery steps ................................................................ 15
Daily cleaning procedures .................................................................................... 22
2|JetScan®MPX 8200 strapping and corner module | Safety information, power specications
Safety information, power specifications
High voltage inside. Risk of electric shock.
Do not attempt repairs. Repairs must be made by authorized
Cummins Allison personnel.
Use grounded plug and properly grounded outlet.
Read and understand all instructions before use.
Risk of injury.
Press MPX 8200 master power switch OFF before cleaning any
automatic-strapping module and any corner module.
Do not defeat safety interlock switches.
Improper voltage levels can cause equipment malfunction,
damage electrical components, and void warranty.
Provide separate circuit serving only this device and follow listed
power requirements to ensure proper operation.
Provide power conditioning/stabilizing devices if necessary.
Automatic-strapping module
•Voltageoperatingrange: 105-130 VAC
•Frequency: 50/60 Hz
•Fullloadamps(FLA): 3A
•Electricalsupplycircuit: The customer must provide a single-phase, dedicated power line that meets the
machine’s power requirements. Use a properly grounded circuit breaker in compliance with applicable local
electrical code.
Corner module
The corner module does not have a power cord or a power switch. It obtains power from the adjacent
automatic-strapping module.
Environmentaloperatingconditions
•Temperature: 60°F - 85°F (15°C - 29°C)
•Humidity: 30% to 70% (non-condensing)
Compliance acknowledgments
•Laser: This equipment may contain Class 2 laser products and complies with FDA Radiation Performance
Standards, 21 CFR Subchapter 1 and the international laser safety standard IEC-60825.1-2001-08.
• FCC: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Table of contents | JetScan®MPX 8200 strapping and corner module | 3
Table of contents
Safety information, power specications ................................................................. 2
About this guide .................................................................................................... 3
Strapping module diagram ..................................................................................... 4
Corner module diagram ......................................................................................... 6
Maintaining bins.................................................................................................... 7
Maintaining paper rolls .......................................................................................... 8
Maintaining printer ribbon cartridge ...................................................................... 10
Conguring strap length and printing .................................................................... 11
Stopping conditions and recovery steps ................................................................ 15
Daily cleaning procedures .................................................................................... 22
About this guide
The automatic-strapping module and corner module are options for the JetScan®MPX
8200 multi-pocket sorter.
A strapping module:
•Separatesasingledenominationintostacksof100notesandautomatically
wraps a paper strap around each stack.
•Canbeconguredtostrapanydenomination.
•Usesatwo-bin,strap-collectionsystemforcontinuousoperation.Eachbincanbe
congured to hold 10, 20 or 30 straps.
A corner module is used to configure a JetScan MPX 8200 system with automatic-
strapping modules into an L- or U-shaped layout for placement in smaller locations
and improved ergonomics.
Contact a Cummins Allison representative for information on conguration options.
See the JetScan MPX 8200 user guide (022-8101-00) for:
• Additionalsafetyinformationandpowerspecications.
• Keymachinefunctions.
• Additionalstoppingconditionsandrecoverysteps.
• Additionaldailycleaningprocedures.
See the JetScan MPX 8200 operating instructions (022-8100-00) for:
• Comprehensivemachinefunctions.
• Additionalstoppingconditionsandrecoverysteps.
4|JetScan®MPX 8200 strapping and corner module | Strapping module diagram
Strapping module diagram
1
2
3
8
7
5
6
4
11
10
7
9
No. Item No. Item
1Upper-front access door
(transport access door) 7Lower paper-roll access door
2Transport path 8Paper roll
3Note stacker No. 2 (left) 9Printer ribbon cartridge
4Note stacker No. 1 (right) 10 Collection bin No. 1 (right)
5Strap head 11 Collection bin No. 2 (left)
6Strapping section
Strapping module diagram | JetScan®MPX 8200 strapping and corner module | 5
Strap head
The surface below the strap head on a strapping module becomes hot during machine
operation. Avoid contact.
Burn hazard. Hot surface below strap head.
Do not touch.
Hingesonupper-front
access door
Hinges on the left and right side of the
upper-front access door on the strapping
module are pinch points. Keep hands
away from the hinges as the door is
opened and closed.
Hinges on each side of upper-front access door are pinch points
(see above).
Keephandsclear.
No. Item
1Strap head location
2Strap head
2
1
6|JetScan®MPX 8200 strapping and corner module | Corner module diagram
Corner module diagram
No. Item
1Top door closed
2Paper-roll storage access panel on
3Top door open
4Paper-roll storage access panel off
1
2 4
3
Maintaining bins | JetScan®MPX 8200 strapping and corner module | 7
Maintaining bins
Empty the strapped-note collection bin when:
•Onebinisfull.
•Twobinsarefull,andthemachinestopsprocessing.Emptybothcollectionbinsto
continue operation.
Toemptyafullbin:
1. Locate the full bin:
•TheAlert:Strapperbinlimitreached! screen identies a full bin in green, as
shown below.
•Agreenlightalsoilluminatesonthetopofthebinthatisfull.
2. Remove the full bin and empty its contents. The top
of any strapping module can be used as a work
surface.
3. Return the empty bin to the strapping module.
A warning message appears on the main-
processing screen if the empty bin is not
completely inserted into the strapping module.
4. Press OK on the Alert:Strapperbinlimitreached!screen. OK may be pressed
before or after any full bin is removed and emptied.
2
4
8|JetScan®MPX 8200 strapping and corner module | Maintaining paper rolls
Maintaining paper rolls
Toremoveanexistingpaperrolloranemptypaper-rollcorefromastrappingmodule:
1. Open the upper-front access door and lower paper-roll access door.
Burn hazard. Hot surface below strap head.
Do not touch.
See the Strap head section for more information.
2. Disengage the loose end of the
strapping paper from the strap head by
doing one of the following:
a. Turning the top, small feed roller
counter-clockwise.
b. Turning the bottom, large feed roller
clockwise.
3. Gently pull the vertical section of
strapping paper along the inside, right
wall of the cabinet so it is completely
free of all guides.
4. Wind the paper roll in a counter-
clockwise direction, until the paper is
free from the paper path and
completely wound around the paper
roll, as shown at right.
5. Pull the paper roll or empty core off
the paper-roll shaft.
6. Set the paper roll aside or discard the
empty core.
Toloadanewpaperrollonastrapping
module:
1. Open the upper-front access door and
lower paper-roll access door.
2. Firmly push the paper-roll core onto
the paper-roll shaft until it stops,
making sure it is inserted so the paper
unwinds in the clockwise direction.
2a
4
2b
Strap
head
2
Maintaining paper rolls | JetScan®MPX 8200 strapping and corner module | 9
3. Unwind approximately 18 inches
(46 cm) of paper.
Make sure the end of the paper
has a clean, straight edge. It is
recommended to cut a new edge with
scissors each time paper is loaded.
4. To nish threading the paper:
a. Thread the paper through the
identied opening.
b. Thread the paper over the black
guide roller.
c. Push the end of the paper into the
upper paper feed, as identied at
right, until it stops at the rollers.
Ensure the back edge of the paper
is ush against the back of the
paper path as it is guided through
and into the upper paper feed.
d. Rotate the top, small roller
clockwise or the bottom, large roller
counter-clockwise until the green
LED illuminates, which indicates the
paper’s leading edge is in the
correct position.
5. Close the upper-front access door and
lower paper-roll access door. The
paper jogs forward and then backward
into position. If the paper does not jog,
repeat steps 1, 4 and 5.
Beware of paper wrinkling or a
paper-crunching sound. If the
paper wrinkles or produces a jam:
• Clearthejam.
• Cutanewpaperedgewith
scissors.
• Repeatsteps4and5.
6. The strapping module is now ready to
operate.
Acceptable
edge
Unacceptable
edge
4a
4d
4d
4c
4b
4a
3
10 | JetScan®MPX 8200 strapping and corner module | Maintaining printer ribbon cartridge
Maintaining printer ribbon cartridge
Tochangetheprinterribboncartridgeonastrappingmodule:
1. Open the upper-front access door and lower paper-roll access door.
2. Firmly grasp the top and bottom of the printer ribbon cartridge and pull outward to
remove the cartridge from its holder. Discard the used cartridge.
3. Firmly grasp the left and right sides of the new printer ribbon cartridge and push it
into the cartridge holder until it snaps into place.
4. Close the upper-front access door and
lower paper-roll access door on the
strapping module.
After closing all access doors,
ensure the upper paper-feed
mechanism jogs the paper
forward and then backward into
its home position.
If the paper does not jog, review
how to load a paper roll in the
Maintaining paper rolls section.
5. The strapping module now is ready to
operate.
3
Table des matières
