Crystal Quest C-75 Manuel utilisateur
2
I. Introduction........................................................................................................3
II. Installation......................................................................................................3-4
Quick Connect Terminal Wiring................................................................................4
III. System Operation..............................................................................................4
.
IV. Warranty and Factory Service Policies.................................................................5
TABLE OF CONTENTS
3
C-75 INTRODUCTION
INSTALLATION
1. The RO pump motor or motor starter and the solenoid valves must be of the same voltage 120 or 240 volt.
2. Conrm that the (3) input signals - pressure switch, tank level switch and pretreat switch are all of the same conguration,
normally open or normally closed.
3. Conrm the desired switch settings for your operation. The switches are factory set to the OFF Position: Auto Reset
(disabled), Pressure Fault Retry (disabled), Tank Full restart time delay (2 seconds), Input contact type (NC, open to operate).
If you desire to change any switch functions, move that switch to the ON Position. [See table below].
4. Wire to the controller as follows:
• Remove the enclosure cover.
• Mark and drill necessary electrical entry holes in the empty enclosure.
• Terminate necessary wiring to the Quick Connect terminals as required (See diagram on page 4). Each terminal is
labeled for the proper connection. Terminals P1-P9 are high voltage for power, motor, inlet and ush solenoid. Utilize proper
3 conductor wire size for the appliance.
WARNING: e controller is rated for maximum 20 amp total load. Terminal strip P11 is dry contact for input signals from tank full,
pressure fault and pretreat lockout. Use small gauge 2 conductor cable for these wire connections.
5. Position and mount the enclosure in the desired location.
6. Connect all wiring to the appropriate appliances (Do not connect to the power source at this time).
7. Reassemble the enclosure, be sure to coil and leave some slack wire inside the enclosure.
8. Connect the power wire 120- 240 volt to its source.
9. Proceed to push the power switch ON and test the completed unit as necessary.
10. Notice the status LED to conrm system status.
The Advantage Controls Series 75 RO controller is designed for the small commercial Reverse Osmosis system. This
controller incorporates relay outputs and dry contact inputs to either run or shutdown as necessary for proper operation.
The S75 Controller has up to three relay outputs: inlet solenoid valve, RO pump motor, and an optional ush solenoid
valve.
The Series 75 Controller is designed for the small commercial Reverse Osmosis system. This controller incorporates relay
outputs and dry contact inputs to either run or shutdown as necessary for proper operation. The S75 Controller has up to
three relay outputs: inlet solenoid valve, RO pump motor, and an optional ush solenoid valve.
The controller’s three inputs will monitor the inlet pressure, tank level, and pretreatment lock. An LED on the front of the
controller will visually indicate the operating status of the RO unit. The S75 can operate a one horse power single phase
pump motor directly with the RO pump relay output. This controller provides crucial time delays required to prevent the
RO unit from false shutdowns.
4
INSTALLATION
SYSTEM OPERATION
When the power switch is turned ON, the center status LED will ash Green, the inlet valve will OPEN and the RO pump will START. The center
LED will be solid Green for normal run.
Under normal operation the RO unit will run until: (A) the storage tank is full (left status LED Amber) or (B) Pretreat lockout has occurred (center
status LED Flashing Green). When A or B has cleared, after a time delay, the RO unit will restart, and the status LED will return to Green. Switch
setting 3 selects a 2 second or 15 minute tank full restart time delay.
Upon an alarm signal for Pressure Fault, the left status LED will ash Red, the RO pump will stop and the inlet valve will close and the RO pump
will turn OFF.
If switch 1 and 2 are in the OFF Position (disabled), the left status LED will be a steady RED and the RO will not restart until the Power Switch
has been manually cycled OFF then ON to reset the unit.
If switch 1 is in the ON Position (auto reset), every 60 minutes the RO will start and stop again if a pressure fault continues.
If switch 2 is in the ON Position (pressure fault retry), the RO will attempt to restart after 30 seconds, then 5 minutes, then 30 minutes. If the
pressure alarm has not cleared after the third try, the RO unit will remain off until manually reset.
If switch 1 and 2 are in the ON Position, after a pressure fault condition, the RO unit will continually attempt to restart after each 60 minute
cycle, until the pressure switch input has cleared.
If switch 5 is in the OFF position, Flush is disabled; in the ON position, Flush is enabled.
If switch 6 is in the OFF position, the unit will ush on Tank Full. In the ON position, ush is every 24 hours elapsed time.
Flush time is 5 minutes. The Amber Flush LED with ash.
Switch 4 is for switch inputs. OFF is for N.O. contacts. ON is for N.C. contacts
WARNING: All switch inputs must be dry contact only. If voltage is applied to these inputs, damage to the controller will
result. For power with neutral and hot leads, L1 is hot and L2 is neutral.
5
WARRANTY & GUARANTEE
VOID ABILITY OF WARRANTY
This Warranty shall be void and unenforceable as to any Seller product which has been damaged by accident, mishandling,
abuse or has been repaired, modied, altered, disassembled or otherwise tampered with by anyone other than Seller
or an authorized Seller service representative; or, if any replacement parts are not authorized by Seller have been used,
or, the product has not been installed, operated and maintained in strict accordance and adherence with the operating
documentation and manuals for such product. Any expressed warranty, or similar representation of performance set forth
in the operation documentation or a reverse osmosis, nanoltration, or ultraltration membrane incorporated into a Seller
product shall be void and unenforceable unless the feed water requirements set forth in the operating documentation for
such product are unequivocally and strictly adhered to.
LIMITATIONS AND EXCLUSIONS
THIS WARRANTY AND REMEDIES DESCRIBED HEREIN AND HEREIN ABOVE ARE EXCLUSIVE AND IN LIEU OF ANY AND
ALL OTHER WARRANTY OR REMEDIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL THE SELLER BE
LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL OR OTHER SIMILAR TYPES OF DAMAGES, FOR DAMAGES FOR THE
LOSS OF PRODUCTION OR PROFITS, OR INJURY TO PERSON OR PROPERTY. NO PERSON HAS ANY AUTHORITY TO
BIND SELLER TO OTHER THAN WHAT IS SET FORTH ABOVE.
THIS WARRANTY GIVES THE BUYER SPECIFIC LEGAL RIGHTS AND THE BUYER MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM JURISDICTION TO JURISDICTION. THE PARTIES RECOGNIZE AND AGREE, THAT IN ALL RESPECTS
THE LAWS OF THE STATE OF GEORGIA SHALL APPLY TO AND SHALL GOVERN ANY INTERPRETATION OR LEGAL
SIGNIFICANCE OF THIS DOCUMENT.
NO WARRANTY OR OTHER LIABILITY OF SELLER TO BUYER UNDER THIS AGREEMENT OR OTHERWISE WILL IN ANY
EVENT EXCEED THE COST OF REPLACEMENT OF THE APPLICABLE SELLER PRODUCT, PART, OR ACCESSORY THAT
IS SUBJECT TO ANY BREACH OF SELLER’S WARRANTY. SELLER WILL NOT BE LIABLE FOR ANY DAMAGE TO ANY
PROPERTY OF BUYER OR TO BUYER’S CUSTOMERS FOR ANY CONSEQUENTIAL, INCIDENTAL, OR ECONOMIC LOSS
OR COMMERCIAL DAMAGE WHATSOEVER. REMEDIES HEREIN PROVIDED ARE EXPRESSLY MADE THE SOLE AND
EXCLUSIVE REMEDIES FOR BREACH OF ANY WARRANTY OR OTHER OBLIGATION HEREUNDER EXPRESS OR IMPLIED
OR FROM THE OPERATION OF LAW.
Table des matières
Autres manuels Crystal Quest Contrôleurs
