Crye Precision AIRFRAME Manuel utilisateur
AIRFRAME™HELMET OPERATOR’S MANUAL
This manual must be carefully read by all persons who have or will have the
responsibility for using or maintaining this product.
Any warranties made by Crye Precision LLC with respect to this product are voided if the
product is not used and maintained in accordance with the instructions in this manual. For any
questions relative to the use or repair of this product, please write Crye Precision LLC or call
1-718-246-3838 during regular business hours.
• This product contains integrated ballistic
resistant regions.
• This product is designed to protect the wearer
only against the ballistic threat level stated in
the Product manual. It is not intended to protect
against rie re or sharp edged or pointed
instruments unless specied on the armor.
• Ballistic resistant regions are not intended to
protect the wearer from projectiles that hit
less than 1 inch from any edge of the ballistic
resistant regions.
• Exposure of the internal ballistic materials to
water, chemicals, or sunlight will reduce the
effectiveness of the armor.
• This armor is not ame resistant unless specied
elsewhere in this manual.
• Product that shows no signs of damage must be
replaced 5 years from date of purchase.
• Perform periodic inspections of the ballistic
resistant regions of the armor. Discontinue use
of damaged product immediately.
• DO NOT machine wash or dry clean the product.
Exposure to detergents, bleach, or solvents
may result in degradation and reduce the
effectiveness of the product.
• Inspect the product for discoloration, cuts, tears,
abrasions or cracks before and after each use.
• DO NOT alter the product in any way.
• DO NOT expose the product to open ame or
excessive heat.
• All replacement parts must be acquired from
Crye Precision LLC or a licensed distributor.
• The most current version of this manual may be
found at www.cryeprecision.com.
• DO NOT use this product except in its intended
manner.
The following are general safety warnings intended to call attention to fundamental performance
limitations and areas of the product where proper usage must be followed. Failure to use and maintain
the product according to the instructions and warnings contained herein may result in the product
failing to perform as designed, and/or the persons relying on this product sustaining serious personal
injury and/or death.
EQUIPMENT INFORMATION
01 INTRODUCTION
02 COMPONENT DESCRIPTIONS
OPERATOR INSTRUCTIONS
03 NVG MOUNTING OPTIONS
04 SHELL SIZING
05 PAD PLACEMENT
06 DONNING
07 FIT ADJUSTMENT
08 CLEANING INSTRUCTIONS
08 PREVENTIVE MAINTENANCE CHECKLIST
09 REASSEMBLY
11 SERIAL NUMBERS
CONTENTS
1AIRFRAME™HELMET
INTRODUCTION
The AirFrame™ ballistic helmet sets new standards in protection, comfort, and modularity.
Complete AirFrame™ helmets weigh less than complete ACH 2002 helmets while providing
more coverage area. The AirFrame™ was developed with a mandate to dramatically reduce
headborne weight while exceeding common frag threats. A complete medium AirFrame™
helmet weighs only 2.30 lbs., and the large weighs a mere 2.55 lbs. The unique
overlapping shell design of the AirFrame™ creates an integrated vent that provides passive
cooling and can reduce the damaging effects of explosive blast waves. Each AirFrame™
helmet features an OpsCore®H-Nape Head-Loc™ retention system for unmatched stability,
comfort, and ease of adjustment. Up-armoring the AirFrame™ with ballistic ear or face
protection is simple and fast. All helmets and components are compatible with common ear
pro systems like PELTORS®and SORDINS®. Made in the US from US materials.
FEATURES
Revolutionary vented shell design for passive cooling
Covers more of wearer’s nape than traditional designs
Modular ear and face protection available
Modular ARC-Rail™ system available (O² compatible)
Contain 3/4” pads
Can be pre-drilled at factory for 3-hole or 4-hole NVG mounts (conguration compatible
with OpsCore®and Wilcox®3-hole mounts)
2EQUIPMENT INFORMATION
COMPONENT DESCRIPTIONS
HELMET STRAP9
SMALL T-NUT (x4)
5
FRONT SHELL
1
TRAPEZOIDAL HIT PADS (x2)11
HELMET STRAP BOLTS (x4)
7
SHELL SCREW SHORT (x2)3
MD (x6)
LG (x7)
xL (x 8)
OBLONG PADS10
NYLON INSERT (x2)
6
REAR SHELL
2
LARGE T-NUT (x4)8
SHELL SCREW LONG (x2)4
(IMAGES NOT TO SCALE)
3AIRFRAME™HELMET
NVG MOUNTING OPTIONS
AirFrame™helmets can be ordered with pre-drilled mounting holes for standard 3 or 4 hole night vision mounts. This must be specied at
the time of order.
Standard 3-hole conguration for night vision mounts
Standard 4-hole conguration for night vision mounts
3-hole night vision mount installed
4-hole night vision mount installed
A
D
B
C
4OPERATOR INSTRUCTIONS
SHELL SIZING
Follow the instructions below in order to ensure a correct shell size selection. Select helmet
size based on head circumference. If a measurement falls directly between two sizes, select
the larger size. See note at bottom of page for exceptions. When possible, try on an actual
helmet and let pads adjust for ve minutes to choose size that ts best.
*Note: Pads affect sizing—if using an alternative pad set, try helmet on to choose best size.
MEASURING HEAD CIRCUMFERENCE
Sit straight with head level. Wrap a vinyl tape measure around your head. Start just above
eyebrow ridges and wrap around widest part of the head as shown in the diagram. Pull the
tape measure tight and record the measurement. Use the table below to determine the
correct helmet size.
NOTE: HEAD SHAPES DIFFER
Users on the threshold of two sizes, but with a narrower head (6” width and below), may be
able to t into the smaller sized shell, where users with a wider head (over 6” width) should
move to the larger size.
MEDIUM
20½”–22½”
LARGE
22½”–24½”
X-LARGE
>24½”
5AIRFRAME™HELMET
PAD PLACEMENT
Standard AirFrame™pad placement is shown below. The number of oblong pads varies with helmet size. MEDIUM helmets require 6 oblong
pads, LARGE helmets require 7 oblong pads, and EXTRA LARGE helmets require 8 oblong pads. All helmets require two trapezoidal pads.
EXTRA LARGELARGE
FRONT OF HELMET
BACK OF HELMET
MEDIUM
Pad placement is designed to offer optimal protection and comfort. It is critical that pads are placed as shown in the below diagrams and that
the pads nearest chinstrap hardware mounting points are situated to overlap said hardware—failure to do so may result in injury or death.
A B
Autres manuels pour AIRFRAME
1
Table des matières
Autres manuels Crye Precision Accessoires pour motos
Manuels Accessoires pour motos populaires d'autres marques
SRC
SRC B-TRK502-01-01-SL Manuel utilisateur
3M
3M Speedglas 9100 MP Manuel utilisateur
hepco & becker
hepco & becker 6307520 00 01 Manuel utilisateur
HOMCOM
HOMCOM AA0-077 Manuel utilisateur
hepco & becker
hepco & becker 6307558 00 01 Manuel utilisateur
Wunderkind Custom
Wunderkind Custom 106503-F15 Guide de l'utilisateur
