CruzPro D60 Manuel utilisateur

Page 1

Introduction

The D60 is a compact digital depth gauge. The D60

uses Digital Signal Processing (DSP) to reliably

display water depth from 1.2 foot (0.3 Metre) to

1000 feet (365 Metres). Depth can be displayed in

feet, metres or fathoms. Variable display damping

is provided.

The D60 has programmable shallow, deep and anchor

drag alarms built-in and can display the depth in feet,

metres or fathoms. A keel offset from -20.0 to +20.0

feet can be entered so the D60 shows the depth below

the surface, below the keel or below the transducer.

Fivelevelsofbacklightingcanbeselectedfornighttime

viewingandallsetupconstantsaresavedinanonvolatile

memory.

Page 3

CruzPro

D60

Warranty

Each CruzPro product is carefully tested and

calibrated at the factory before shipping and is

warranted for one full year against original

defects in materials or workmanship. This

warranty does not include damage to the

product resulting from accident or misuse.

If the product should become defective within

the warranty period, we will repair or replace

it free of charge, including free return

transportation, provided it is delivered prepaid

to the dealer from whom it is originally

purchased.

This warranty gives you specific legal rights,

and you may also have other rights which vary

from state to state, or country to country.

Page 14

Setting Display Damping

While viewing Depth press and hold the sand t

keys keys for ten (10) seconds until you hear a long

beep. The display damping value is shown. Use the

sand tkeys to change the value and press the :

key to save your entry. A larger value of damping

will slow down the flickering of the displayed digits

but result in a slower response to depth changes.

The display damping limits are 5 to 20 with 10

being the default value.

1000 Foot

DSP Depth Sounder

With Keel Offset and Alarms

Other CruzPro Products

lDepthsounders, FishFinder & Speed/Temperature/Log

lDC Volts/Amps/Amp-Hour Monitor

lAC Volts/Amps//Freq/kW Monitor

lLPG/Petrol Gas Detectors/Alarms

lBilge Water Alarms & Bilge Pump Controllers

lWindlass Controller/Chain Counter

lDigital Fuel Gauges & Fuel Consumption Calculator

lDigital Tankage Gauges/w Alarms

lSmart Alternator Regulators

lMarine Security System

lRPM/Engine Hours/Elapsed Time Gauge

lDigital Oil Pressure & Water Temp. Gauges/w Alarms

lDigital Rudder Angle Indicator

lOne and Three Bank Digital Volts Gauges

lDigital Amps Gauge

lDigital Clock/Watch/Race Timers/Alarms

l8 and 16 Amp Light Dimmers / Motor Speed Controller

lSolar Panel Charge Controllers 6/8/9 & 20 Amps

l4 & 8 Channel NMEA Combiners/RS-232 Convertors

lEngine/Exhaust Temp. Monitor & Digital Pyrometer

lNMEA 0183 Remote Data Repeater/w 4 Input Channels

Page 4

Specifications

Power supply: 9.5 to 16.0 VDC, .035 amps nom.

Operating temperature: 32 to 122 F ( 0 to 50 C)

Depth Range: 1.2 feet (0.3 Metre) to 1000 feet (365

Metres)

Transducer Frequency: 120 kHz

Size: 2.5" dia X 4.1" deep (61mm x 104 mm)

Deep/Shallow Alarms: 0.0 to 1000 feet (365 Metres)

Keel Offset: -20.0 to +20.0 feet (+/- 7 Metres)

Display: 4 digits. Liquid Crystal Display. Five

levels of backlighting.

Page 13

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Mounting and Wiring. . . . . . . . . . . . . . . . . . . . . . . 6

Mounting the Transducer . . . . . . . . . . . . . . . . . . . 8

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Key Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Backlight Intensity . . . . . . . . . . . . . . . . . . . . . . . . . 9

Selecting Feet/Metres/Fathoms . . . . . . . . . . . . . . . . . 10

Setting Shallow and Deep Alarms . . . . . . . . . . . . . 11

Setting Anchor Drag Alarm . . . . . . . . . . . . . 12

Turning the Alarms ON/OFF . . . . . . . . . . . . . . . . 12

Setting Keel Offset . . . . . . . . . . . . . . . . . . . . . . . . 13

Setting Display Damping . . . . . . . . . . . . . . . . . . . . . .14

Other CruzPro Products . . . . . . . . . . . . . . . . . . . 15

SettingKeel Offset

While viewing Depth, press the tand :keys for ten

(10) second until you hear a long beep. The keel

offset will be displayed. Use the sand tkeys to

change the value and press the :key to save your

entry. The keel offset will be added to the displayed

value of the depth. A negative keel offset is used to

enable the D60 to display depth below the keel or

transducer. A positive keel offset enables you to

display actual water depth when the transducer is

placed below the surface level by up to 20 feet.

2006 CruzPro Ltd. D60MAN-F

http://www.cruzpro.com [email protected]

Page 5

Page 7

Page 10

Figure 1

Installation

Before starting the installation, please read this

entire section first. Be sure to install the bulkhead

gasket before you install the instrument. Finger

tighten the screws that mount the instrument bracket

- do not use tools.

Page 12

Setting Anchor Drag Alarm

After anchoring, set the shallow alarm a few feet

more shallow than the actual displayed depth. Simi-

larly set the deep alarm a few feet deeper than the

actual displayed depth. Make allowances for local

tidal changes to prevent false alarms.

Turning the Alarms ON/OFF

While viewing Depth, press the s key for 1/2

second to turn the alarms ON, or the tkey for 1/2

second to disable the alarms.

Selecting Feet/Metres/Fathoms

While viewing Depth or Fish display quick press

both the tand skeys simultaneously. Each time

you do this, the units will switch from Feet to Metres

to Fathoms to Feet, etc. The alarm values and keel

offset will also change automatically to reflect the

new units.

Figure 2

IMPORTANT

Page 11

Page 6

Page 9

Page 8

MountingandWiring

l Drill a 2-1/8" (55mm) hole where you want to

mount the instrument (Fig. 1).

lBring the transducer/power cable out of the mount-

ing hole and plug the connector onto the instrument

circuit board as shown in figure 2 (page 7). It is

difficult but possible to plug the connector back-

wards if forced - observe polarity. Use a 5 amp fuse

on the power line as shown in Fig 2.

l Carefully check all your wiring against those

shown in figure 2. If everything is wired correctly

you can mount the D60 in the instrument hole. Be sure

the bulkhead gasket is in place and use only finger

tension to tighten the bracket hold-down nuts Do not

overtighten the bracket or you may damage the case

- do not use tools to tighten the nuts.

Operation

Key Functions

The keys are used to set

backlight levels, select Feet/Metres/Fathoms, and to

adjust keel offset and alarm depths. After changes

are made, the new information is automatically saved

to memory.

Backlight Intensity

Press the :key for 1/2 second to adjust the

backlight level for nighttime viewing. Each time you

pressthe "+" key thebacklight level will change:1, 2, 3,

4, OFF, 1, 2, ... etc.

SettingShallow and DeepAlarms

While viewing Depth, press the tkey for 10 seconds

to view/set the deep alarm. You will hear a long beep

and the deep alarm value is displayed. Use the sand

tkeys to change the value and press the :key to

save your entry.

To view/set the shallow alarm, press the skey for 10

seconds to view/set the shallow alarm. You will hear

a long beep and the shallow alarm value is displayed.

Use the sand tkeys to change the value and press

the :key to save your entry.

Mounting the Transducer

The instruction for mounting the transducer are pro-

videdseparatelywith the transducer anddependsupon

the type of transducer you selected. The RED wire

should be connected to +12VDC. The BLACK wire

connects to power ground. The combination trans-

ducer/powerconnector is keyedwith a ridge thatlocks

thefemaleconnectorinplace. Itisdifficultbutpossible

to force the connector onto the matching male plug

backwards. Be careful to plug in the connector as

shown on page 7 or you will damage the electronics.

Manuels Instrument de plongée populaires d'autres marques

Sherwood

Sherwood Amphos Manuel utilisateur

Zeagle

Zeagle N2ition Manuel utilisateur

Tusa

Tusa Q 1203 CE Mode d’emploi

Sherwood Scuba

Sherwood Scuba Insight Instructions de montage

SUBMERSIBLE SYSTEMS

SUBMERSIBLE SYSTEMS Spare Air 600 Manuel utilisateur

OCEANS

OCEANS S1 Supersonic Manuel utilisateur

heinrichs weikamp

heinrichs weikamp OSTC 2 Manuel utilisateur

Omer

Omer SP2 Manuel utilisateur

Scott

Scott PRO-PAK Manuel utilisateur

Apeks

Apeks BLACK SAPPHIRE Manuel utilisateur

Waterproof

Waterproof DRYSUIT Manuel utilisateur

Dräger

Dräger PAS AirPack 1 Manuel utilisateur

Dive Lab

Dive Lab KIRBY MORGAN KMB 18 Manuel utilisateur

Ratio Computers

Ratio Computers iDive Manuel utilisateur

Oceanic

Oceanic PROPLUS X Manuel utilisateur

CFA

CFA MSA G1 Manuel utilisateur

Genesis

Genesis Centauri Manuel utilisateur

TREND

TREND GAUGE/60 Manuel utilisateur