11
12
13
FIG.4 - PCB LAYOUT
FIG. 5 - OPTIONAL OLES
FIG. 6 - WA PIR + MW DETECTION
PATTERN
FIG. 7 - BRACKET MOUNTING AND ASSEMBLY
TEST PROCEDURES
Wait one-minute for warm-up time after applying
power.
Make the test at the protected area free of moving
people. LED should be in enable position.
Walk test
1. Start walking slowly across the detection zone.
2. Observe that the red LED lights whenever
motion is detected.
3. Allow 5 sec. between each test for the detector
to stabilize.
NOTE:
Walk tests should be done at least once a year to
confirm proper operation of the detector.
TEC NICAL SPECIFICATIONS
Detection Method DO BLE D AL element PIR & MW
Maximum ripple 2.4Vdc peak to peak at 12Vdc
Power Input 8.2 to 16 Vdc
Current Draw Start-up: 28mA + 3mA
Standby: 23mA + 3mA
Active : 20mA + 3mA
Temperature
Compensation YES
Alarm Period 1.8 sec
Alarm Output N.C 28Vdc 0.1 A with 10 Ohm
series protection resistors
N.O 28Vdc 0.1 A with 10 Ohm
series protection resistors
Tamper Switch N.C 28Vdc 0.1A with 10 Ohm series
Protection resistor - open when
cover is removed
Warm p Period 60 sec
TEC NICAL SPECIFICATIONS (CONT.)
Operating Temperature -20°C to +50°C(-4°F to +122°F)
RFI Protection 30V/m 10 - 1000MHz
EMI Protection 50,000V of electrical
interference from lightning or
power through
Visible Light Protection stable against halogen light
2.4 m (8ft ) or reflected light
MW center frequency X-Band: 9.9 GHz
10.525 GHz
10.687 GHz
Dimensions 154mm x 114mm x 74mm
(6.1” x 4.5” x 2.9”)
Weight 290gr. (10.23oz)
CROW reserves the rights to change
specifications without prior notice
CROW ELECTRONIC ENGINEERING LTD. ("Crow") –
WARRANTY POLICY CERTIFICATE
This Warranty Certificate is given in favor of the p rchaser (here nder the
"Purchaser") p rchasing the prod cts directly from Crow or from its a thorized
distrib tor.
Crow warrants these prod cts to be free from defects in materials and
workmanship nder normal se and service for a period of 24 months from the
last day of the week and year whose n mbers are printed on the printed circ it
board inside these prod cts (here nder the "Warranty Period").
S bject to the provisions of this Warranty Certificate, d ring the Warranty
Period, Crow ndertakes, at its sole discretion and s bject to Crow's
proced res, as s ch proced res are form time to time, to repair or replace, free
of charge for materials and/or labor, prod cts proved to be defective in
materials or workmanship nder normal se and service. Repaired prod cts
shall be warranted for the remainder of the original Warranty Period.
All transportation costs and in-transit risk of loss or damage related, directly or
indirectly, to prod cts ret rned to Crow for repair or replacement shall be borne
solely by the P rchaser.
Crow's warranty nder this Warranty Certificate does not cover prod cts that is
defective (or shall become defective) d e to: (a) alteration of the prod cts (or
any part thereof) by anyone other than Crow; (b) accident, ab se, negligence,
or improper maintenance; (c) fail re ca sed by a prod ct which Crow did not
provide; (d) fail re ca sed by software or hardware which Crow did not provide;
(e) se or storage other than in accordance with Crow’s specified operating and
storage instr ctions.
There are no warranties, expressed or implied, of merchantability or fitness of
the prod cts for a partic lar p rpose or otherwise, which extend beyond the
description on the face hereof.
This limited Warranty Certificate is the P rchaser's sole and excl sive remedy
against Crow and Crow's sole and excl sive liability toward the P rchaser in
connection with the prod cts, incl ding witho t limitation - for defects or
malf nctions of the prod cts. This Warranty Certificate replaces all other
warranties and liabilities, whether oral, written, (non-mandatory) stat tory,
contract al, in tort or otherwise.
In no case shall Crow be liable to anyone for any conseq ential or incidental
damages (incl sive of loss of profit, and whether occasioned by negligence of
the Crow or any third party on its behalf) for breach of this or any other
warranty, expressed or implied, or pon any other basis of liability whatsoever.
Crow does not represent that these prod cts can not be compromised or
circ mvented; that these prod cts will prevent any person inj ry or property
loss or damage by b rglary, robbery, fire or otherwise; or that these prod cts
will in all cases provide adeq ate warning or protection.
P rchaser nderstands that a properly installed and maintained prod ct may in
some cases red ce the risk of b rglary, fire, robbery or other events occ rring
witho t providing an alarm, b t it is not ins rance or a g arantee that s ch will
not occ r or that there will be no personal inj ry or property loss or damage as
a res lt.
Conseq ently, Crow shall have no liability for any personal inj ry; property
damage or any other loss based on claim that these prod cts failed to give any
warning.
If Crow is held liable, whether directly or indirectly, for any loss or damage with
regards to these prod cts, regardless of ca se or origin, Crow’s maxim m
liability shall not in any case exceed the p rchase price of these prod cts,
which shall be the complete and excl sive remedy against Crow.
CROW ELECTRONIC ENGINEERING LTD.
ISRAEL: Crow Electronic Engineering Ltd.
12 Kineret St. Airport City, 70100
PO. Box 293 Ben Gurion Airport
Tel: 972-3-9726000
Fax: 972-3-9726001
E-mail: support@crow.co.il
USA: 2160 North Central Road,
Fort Lee, N.J. 07024
Tel: 1-800-GET CROW
or (201) 944 0005
Fax: (201) 944 1199
E-mail: support@crowelec.com
AUSTRALIA: 429 Nepean HWY Brighton East Vic 3187
Tel: 61-3-9596 7222
Fax: 61-3-9596 0888
E-mail: crow@crowaust.com.au
POLAND: VIDICON SP. ZO. O.
15 Povazkowska St.
01 – 797 Warsaw Poland
Tel: 48 22 562 3000
Fax: 48 22 562 3030
E-mail: vidicon@vidicon.pl
LATIN AMERICA: CROW LATIN AMERICA
5753 NW 151ST.Street
MIAMI LAKES,
FL 33014 – SA
Tel: +1-305-823-8700
Fax: +1-305-823-8711
E-mail: sales@crowlatinamerica.com
ITALY: DEATRONIC
VIA Giulianello 4/14
00178 ROMA, ITALY
Tel: +39-0676-12912
Fax: +39-0676-12601
E-mail: info@deatronic.com
These instructions supersede all previous issues in circulation prior to July 2005.
7101296_F
ANTENNA
DOPPLE
BLOCK
CONNECTO
ALA M
LED
OTA Y
SWITCH PI MW
LED LED
LED
Mode
Jumper
Tamper
Double Dual Pyrosensors on opposite side
A. Wire access holes
B. se for flat wall mounting or for
mounting with the help of bracket
A A
B
B
B
You must reset the detector from
Control Panel before the new
settings will take effect
2
1
BRACKET SCREW
Install part 1 to wall using 4 screws; connect part 2
to part 1, adjust the detector to required direction
and tighten the bracket screw
Assembled view
