Crestron SSW-100 Manuel utilisateur

DO GUIDE

DO Install the SSW

The SSW installs over a standard 1-gang U.S. electrical box. Use the following procedure to install

the SSW:

1. Once all cable connections have been made, use the two included 6-32 x 5/16" screws and

a Phillips screwdriver (not included) to attach the SSW rear assembly to the electrical box, as

shown in the following illustration.

NOTE: For retrot installations, the SSW can be installed over a 1-gang plaster ring using the

same installation method described above.

SSW-100/SSW-102

Room Availability Hallway Sign, Wall Mount

DO Connect the SSW

The Crestron®SSW can be powered and controlled using one of the following connection methods:

•USB: Use the included USB cable to connect the SSW to a Crestron TSW-560, TSW-760, or

TSW-1060 touch screen. Connect the cable’s USB A connector to the touch screen and the

micro USB connector to the SSW rear assembly. Although the touch screen can be powered

using standard PoE (power over Ethernet), it must be powered using PoE+ to supply power to

the SSW over USB. Out-of-the-box functionality is established via the scheduling SmartObject®

program with no programming required.

•Cresnet®Network: Use any standard Cresnet cable (not included) to connect the SSW to a

Crestron control system or DMPS device. The SSW is powered and controlled over Cresnet via

programming in SIMPL Windows or Crestron Studio®software.

NOTE: The CNET ID button on the front of the assembly is used to identify the device on

the network using the Network Device Tree View in Crestron Toolbox™ software. For more

information, refer to the embedded Crestron Toolbox help le.

NOTE: All cable connections must be made prior to installing the SSW.

NOTE: Use Crestron power supplies for Crestron equipment.

DO Check the Box

QTY PRODUCT COLOR PART NUM.

1Bezel, Wall Sign Clear 4525866

1 Cable, USB 2.0, A - micro B, 6’ (1.83 m) 2038114

2 Screw, 4-40 x 1/2", SEMS, Pan Head, Phillips 2011592

2 Screw, 6-32 x 5/16", Pan Head, Phillips 2007221

1 Sign, 8.0" x 5.25" x 0.5" 4525763

CNET (24 Y Z G):

To Cresnet

network device

USB (Micro):

To touch screen

Rear

assembly

1-gang U.S.

electrical

box

Screws (2):

6-32 x 5/16"

DO GUIDE

3. To complete the installation, carefully slide the bezel over the acrylic face and across the sign

until the bezel is magnetically locked into place against the rear assembly.

DOC. 7969B (2048129) 04.17

Specications subject to change without notice.

2. Align the two holes on the acrylic face with the mounting posts on the rear assembly, and then

push the acrylic face into the assembly so that the holes completely engage the posts. The

acrylic face stays in place once it is hung onto the posts. Then, use the two included 4-40 x 1/2"

SEMS screws and a Phillips screwdriver to secure the acrylic face to the posts. Remove the

plastic lm from the acrylic face once it is secured.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

CAUTION:Changes or modications not expressly approved by the manufacturer responsible for compliance could void the

user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

The specic patents that cover Crestron products are listed at http://www.crestron.com/legal/patents. The product warranty can be found at www.crestron.com/warranty.

Certain Crestron products contain open source software. For specic information, please visit www.crestron.com/opensource.

Crestron, the Crestron logo, Cresnet, Crestron Studio, Crestron Toolbox, and SmartObject are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or

other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron