Creative PC 66B Manuel utilisateur
User Manual for Handheld Pulse Oximeter
I
Instructions to User
Dear Customer,
Thank you for purchasing this quality product. Please read the
manual very carefully before using this device. Failure to follow
these instructions can cause measuring abnormality or damage to
the Oximeter.
No part of this manual may be photocopied, reproduced or
translated into another language without the prior written
consent. We reserve the right to revise and amend it at any time
without prior notice.
Version of the Manual: Ver 1.2
Issued Date: September 29, 2014
All rights reserved.
Notes:
zThe contents contained in this manual are subject to change
without prior notice.
zInformation furnished by Creative is believed to be accurate
and reliable. However, no responsibility is assumed by
Creative for its use, or any infringements of patents or other
rights of third parties that may result from its use.
3502-2490003
User Manual for Handheld Pulse Oximeter
II
Instructions for Safe Operation
0Check the device to make sure that there is no visible
damage that may affect user’s safety and measurement
performance. It is recommended that the device should
be inspected minimally before each use. If there is
obvious damage, stop using the device.
0Necessary service must be performed only by qualified
technicians. Users are not permitted to service this
device.
0The oximeter must not be used with the devices and
accessories not specified in User Manual.
Cautions
0Explosive hazard—DO NOT use the oximeter in
environment with inflammable gas such as some
ignitable anesthetic agents.
0DO NOT use the oximete
r
while the Patient is unde
r
MRI o
r
CT scannin
g
.ThisdeviceisNOTMRI
Compatible.
Warnings
0Discomfortable or pain may occur if using the sensor of
this device continuously on the same location for a long
time, especially for the patients with poor
microcirculation. It is recommended that the Oximeter
should not be applied to the same location for longer than
2 hours or less if any abnormal condition is found.
Frequently check and re-position the Oximeter.
User Manual for Handheld Pulse Oximeter
III
0For the individual patients, there should be a more
prudent inspecting in the placing process. The sensor can
not be placed on the edema and tender tissue.
0The local law should be followed when disposing of the
expired device or its accessories.
Attentions
Keep the oximeter away from dust, vibration, corrosive
substances, explosive materials, high temperature and
moisture.
If the Oximeter gets wet, please stop operating it and do
not resume operation until it is dry and checked for
correct operation. When it is carried from a cold
environment to a warm and humid environment, please
do not use it immediately. Allow at least 15 minutes for
the Oximeter to reach ambient temperature.
DO NOT operate the button on the front panel with sharp
materials or sharp point.
DO NOT use high temperature or high pressure steam
disinfection on the oximeter and probes. Refer to related
chapter for instructions regarding cleaning and
disinfection.
The intended use of this device is not for therapy purpose.
Declaration of Conformity
The manufacture
r
hereb
y
declares that this device com
p
lies
with the following standards:
IEC 60601-1, ISO 9919:2009,ISO 80601-2-61:2011
User Manual for Handheld Pulse Oximeter
IV
and follows the provisions of the council directive
MDD93/42/EEC.
Caution: U.S. federal law restricts this device to sale
or use by or on the order of a physician.
User Manual for Handheld Pulse Oximeter
V
Table of Contents
1 Overview.................................................................................. 1
1.1 Appearance....................................................................... 1
1.2 Product Name and Model.................................................. 2
1.3 Structure............................................................................ 3
1.4 Features............................................................................. 3
1.5 Intended Use..................................................................... 3
1.6 Working Environment....................................................... 3
2 Installation of Battery and Holder........................................ 4
3 SpO2Probe Connection.......................................................... 6
4 Operation................................................................................ 8
4.1 Power on/off the Oximeter................................................ 8
4.2 Default Display Screen..................................................... 8
4.3 Display Screen with PI Value......................................... 10
4.4 Menu Setup..................................................................... 10
4.5 Data Recall...................................................................... 16
5 Technical Specifications....................................................... 20
6 Over-limit Indication............................................................ 22
6.1 Limit settings.................................................................. 22
6.2 Alert sound mute setting................................................. 22
7 Accessories............................................................................. 23
8 Repair and Maintenance...................................................... 24
8.1 Maintenance.................................................................... 24
8.2 Cleaning and Disinfecting Instruction.............................24
9 Troubleshooting.................................................................... 25
Appendix.................................................................................. 26
User Manual for Handheld Pulse Oximeter
1
1 Overview
1.1Appearance
Figure 1-1
1. Display screen: display SpO2plethysmogram and parameter
values.
2. Navigation key:
¿: Up/Left/Increase
Data interface
Display Key
Navigation knob
DC power input
Power/Back
Recall/Mute
SpO2probe
connector
Mode/OK
User Manual for Handheld Pulse Oximeter
2
Press this key, the default screen can be shifted to display pulse
rate (PR) or perfusion index (PI). If on the system setup screen,
press it to move the cursor upwards or to the left and adjust
parameter values.
À: Down/Right/Decrease
Its function is similar with the key “¿: Up/Left/Increase”.
3. (Mode/OK): press this key, the screen can be shifted
between default screen display and alternative screen display;
longtime press it, the menu screen will be displayed; when you
finish parameter setting, press this key to confirm.
4. (Data interface): used for uploading data (Optional
function).
5. (DC power input): used for connecting external DC
power input for recharging the built-in rechargeable battery.
6. (Power/Back): Power on/off the device by longtime
pressing; short time press it to back to the previous level of menu
while setting menu operation.
7. (Recall/Mute): Longtime press it to enter SpO2trend data
recall screen; when the device is beeping, short time pressing
will mute the indication sound, the mute state will persist for
about 90s. After this mute period (90s), then the indication sound
will resume.
8. Icon: “SpO2”:SpO
2Probe Connector.
1.2 Product Name and Model
Name: Handheld Pulse Oximeter
User Manual for Handheld Pulse Oximeter
3
Model: PC-66B
1.3 Structure
It consists of the main unit and SpO2probe.
1.4 Features
It is lightweight, small in size and easy to carry
Color LCD to display plethysmogram and parameters
Monitor SpO2and Pulse Rate simultaneously
PI (Perfusion Index) display is available
Up to 384 hours storage and recall of SpO2and PR data.
Audible and visual alert function is available
Data transmission to PC for view and analysis (Optional)
Power saving mode is available
1.5 Intended Use
This Handheld Pulse Oximeter is intended for measuring and
recording the pulse rate and functional oxygen saturation (SpO2).
It is applicable for monitoring SpO2and pulse rate of adult and
pediatric patients in clinical institutions and homes.
1.6 Working Environment
Operating temperature: 5~40℃
Operating humidity: 30~80%
Atmospheric
p
ressure: 70kPa~106kPa
User Manual for Handheld Pulse Oximeter
4
2 Installation of Battery and Holder
1）Open the rear panel with coin or an ordinary flat
screwdriver, as shown in Figure 2-1.
Figure 2-1
2）AAAlkaline batteries or Lithium battery (optional):
①If AA alkaline batteries (non-chargeable) are provided, then
according to the polarity mark, insert three AA batteries into
battery house, as shown in Figure 2-2.
Figure 2-2 Figure 2-3 Fixing Holder
User Manual for Handheld Pulse Oximeter
5
②If Lithium battery (rechargeable) is provided, place the
lithium battery into the battery house, and insert its
terminal header into the corresponding connector in the
battery compartment.
3）Close the battery cover and lock it.
4）Fixing Holder, as shown in figure 2-3.
Notes: ①When the device is provided with AA alkaline
batteries and it shows low battery, the user should replace the
batteries in time.
②When the device is provided with lithium battery and it
shows low battery, the user should recharge the battery in time.
That is, connect one end of the charging cable to the device's
DC power input, and connect the other end to the USB power
(from PC or DC adapter). When the display screen appears the
rolling icon " ", it means the battery is charging; When the
screen shows icon " ", it means the battery is fully
charged. Pulling out the charging cable, then the above icon will
disappear.
Safety instruction for operation:
0Do not throw the battery into the water, liquid and fire.
0Keep the battery out of the reach of the child.
0Do not disassemble the battery.
Please remove the battery and put it to specified condition if
the device will not be used for a long time.
If the battery is damaged, please replace it with the same
model AA alkaline battery or lithium battery provided by the
same manufacturer.
Autres manuels pour PC 66B
1
Table des matières
Autres manuels Creative Équipement médical
Creative
Creative PC-68A Mode d’emploi
Creative
Creative PC 66B Mode d’emploi
Creative
Creative PC-66A Manuel utilisateur
Creative
Creative PC-60NW Manuel utilisateur
Creative
Creative PC-60N Manuel utilisateur
Creative
Creative PC-68B Manuel utilisateur
Creative
Creative OXY-110 Mode d’emploi
Creative
Creative OXY-11 Manuel utilisateur
Creative
Creative PC-60NW-1 Manuel utilisateur
Creative
Creative POD-1 Manuel utilisateur
