CRE MASTER COMPACT 1B Manuel utilisateur

ACTIVE DISPLAY

OPERATING

MODES/CONTROL

BUTTONS

Quick start

MASTER COMPACT 1B

CRE TECHNOLOGY - 130, allée Charles-Victor Naudin - Zone des Templiers - SOPHIA ANTIPOLIS - 06410 BIOT - FRANCE

Phone : + 33 (0)4 .92.38.86.82 - www.cretechnology.com - info@cretechnology.com

Document index: D

OPERATIONNAL MODES

The purpose of this document is to allow a fast and easy

handling of the product, nevertheless it is essential that you

refer to the technical documentation (latest version always

available on our website www.cretechnology.com) for the

commissioning.

For any further information on this product, please contact

your local distributor or agent or directly our support team.

• All our products have a 1 year warranty

• Help desk: +33 492 38 86 86

• E-mail: support@cretechnology.com

The controller can be conﬁgured and controlled using the buttons of the front panel:

• The arrows, ESC and ENTER buttons are dedicated to navigation for displaying measurements and parameters, and for conﬁguring the controller.

• The SHIFT button is used to reset faults when combined with the alarms/faults button

• The AUTO button switches to a mode that makes the controller operate the installation in a fully automatic mode according to its settings and conﬁguration, external action to start : "re-

mote start" digital input or "mains failure" by ModBus TCP.

• The TEST button switches to a mode that simulates the start of the Auto mode with the requested sequences. To exit from the TEST mode, simply press AUTO or press MAN mode.

• The MAN button switches to a mode allowing you to manage your installation with the front panel buttons manually: you will be able to start/stop the power plant, open/close the breaker

while still beneﬁting from the active protections of the controller and the automatic synchronization and load/unload sequences.

When the controller is powered up, the home page appears on the screen. The content of this page is dynamic, depending on the status of the power plant. Press "ENTER" to access the index page of

available menus:

• Supervision : Use the arrow buttons to select this menu, then press "ENTER" to access the supervision pages.

• Settings : Use the arrow buttons to select this menu, then press "ENTER" to access the settings pages. A password is required to deﬁne the operating mode. To enter the password: Use

the "↑" and "↓" buttons to change character, move to the next/previous character with the "→" and "←" buttons, conﬁrm password by pressing "ENTER". The operating modes are the

following:

• Standard: Provides access to the basic settings recommended to start commissioning your application. The default password is "1".

• Advanced: Provides access to all settings for optimum application commissioning. For complex settings not available on the controller front panel, use the i4Gen Suite software (Easy-

Flex, scheduler, alternative selection, etc.). The default password is "1234".

MENUS

THE DIFFERENT MENUS WILL APPEAR AS FOLLOW

SUPERVISION

POWER PLANT Power plant electrical information: kW /kVAR, nominal values, breakers

status and generator state.

BUS Bus electrical measures: frequency, voltage, powers and power factor.

MAINS Mains electrical measures: frequency, voltage, powers, currents and

power factor.

SYNCHRONIZATION Synchronization measures and checks: phase, frequency, voltage, phase

sequence.

INPUTS/OUTPUTS Real time displays for digital I/Os, and CANopen digital I/Os.

ABOUT Information about hardware and ﬁrmware: serial number, ﬁrmware

version.

SETTINGS (*LEVEL 2 ONLY)

DYNAMIC PID settings.

GENERAL Application, timers, CAN and events settings.

ELECTRICAL Bus, mains, synchronization and power management settings.

INPUTS/OUTPUTS Digital inputs, analog inputs, digital/relay outputs and breaker settings.

PROTECTIONS*Bus, mains and other protections settings.

PROGRAMMING*Modiﬁcation by variable number.

SYSTEM Language, screen setup, date/time, Ethernet and password settings.

Quick start

MASTER COMPACT 1B

CRE TECHNOLOGY - 130, allée Charles-Victor Naudin - Zone des Templiers - SOPHIA ANTIPOLIS - 06410 BIOT - FRANCE

Phone : + 33 (0)4 .92.38.86.82 - www.cretechnology.com - info@cretechnology.com

Document index: D

PC CONNECTION - WITH I4GEN SUITE SOFTWARE

• In MAN mode: Open and Close the Mains breaker.

• Disconnect the breaker relay output of the controller. Apply synchronization (on Bus sides, GENSYS COMPACT PRIME must be in AUTO mode), and check if frequency, phase and voltage

difference are within the expected limits. Apply the same procedure on the Mains breaker.

• Mains paralleling can be tested, and stability can be adjusted. If frequency or voltage synchronization or power ramp management are not performing well, adjust the PID settings on the

GENSYS COMPACT PRIME controllers

• After commissioning, the product can be switched to AUTO mode.

CONTROL LOOPS ADJUSTMENT

To adjust these parameters, we provide real-time display of setpoint and measurement curves on the same screen. These 2 curves help to adjust

PID for global stability and are available for synchronization (phase).

• In standard operating mode, you have access to the global gain G setting.

• In advanced operating mode, you have access to the proportional P, integral I and derivative D settings:

• Increase P value to have measure curve close to setpoint curse, without hunting.

• Increase I to decrease the static error (difference between setpoint and measure), without slow hunting.

• Only if necessary, increase D, for oscillation attenuation.

Wiring & Dimensions/Panel cut out are available on the website in the technical documentations section of the controller: www.cretechnology.com

WIRING CONNECTION

COMMISSIONING

Switch on the controller. Connect the Ethernet port (RJ45-LAN) of your computer to the Ethernet port of the controller. To be able to establish communication between the i4Gen Suite and the controller,

the network addresses of both devices should be conﬁgured:

• For PC network conﬁguration, please refer to your Windows network settings.

• To conﬁgure the controller IP address, proceed as follows:

1. Download the latest version of the i4Gen Suite software on our website https://www.cretechnology.com/en/software/130/i4gen-suite

2. Open the i4Gen Suite software and go on Easy connect menu.

3. Click on the scan button to identify your controller.

4. Click on the auto conﬁguration button to adapt your controller's IP address.

5. Your system is ready. Click on the connection button to access supervision, conﬁguration and control of your controller.

Once connected, you will be able to navigate through the following menus:

CONTROLLER SUPERVISION

(Controller measurement supervision)

PC SETTINGS

(PC software settings)

CONTROLLER SETTINGS

(Controller parameters settings)

NOTE

Before the commissioning or the operation of your equipment, please read carefully the user’s manual and other related documentations.

We also offer personalized and speciﬁc training on our product range and software, as well as additional services such as: onsite support, application engineering or speciﬁc support.