Craftsman 315.212100 Manuel utilisateur

Owner's Manual

IERRFTSMRN'I

ACCESSORIES FOR MODEL NOS. 315.212100 AND 315.212110

10 in. (254 mm) COMPOUND MITER SAW

Item No.

_924310

_924350

Save this manual for

future reference.

_, CAUTION: Read and follow

all Safety Rules and Operating

Instructions before first use of

this product.

• SAFETY

•LOOSE PARTS

•INSTALLATION

•SERVICES

Customer Help Line: t-800-932-3188

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

Visit the Craftsman web page: www.sears.com/craftsman

972000-603

2-00

READ ALL INSTRUCTIONS

•READ THESE INSTRUCTIONS AND THE IN-

STRUCTIONS FOR THE 315.212100 COM-

POUND MITER SAW THOROUGHLY before

using accessories.

•KNOW YOUR POWER TOOL. Read the owner's

manual for the Compound Miter Saw carefully.

Learn the saw's applications and timitations as well

as the specific potential hazards related to this

tool,

•KEEP THE WORK AREA CLEAN, Cluttered work

areas and work benches invite accidents. DO NOT

leave tools or pieces of wood on the saw while it is

in operation.

•ALWAYS WEAR SAFETY GLASSES. Everyday

eyeglasses have only impact-resistant lenses; they

are NOT safety glasses.

•ALWAYS DISCONNECT SAW FROM POWER

SUPPLY BEFORE MAKING ADJUSTMENTS OR

ADDING ACCESSORIES. Make sure the switch is

offwhen reconnecting to power supply.

•SAVE THESE INSTRUCTIONS. Refer tothem

frequently and use to instructother users. If you

loan someone thistool, loan them these instruc-

tionsalso.

_k Look for this symbol to point out important safety precautions. It

means attention!!! Your safety is involved.

The following accessories are includedwith item no. 924310 and &2.4350:

• Work Clamp

• Dust Bag

• Table Extensions (2)

• Stop Block

• Small Wing Screw

• Clamp Bracket (2)

• Clamp Bracket Screws (2)

• Owner's Manual

WORKCLAMP

SMALL WINGBCREW

EXTENSIONS

S_CREW

STOPBLOCK

CLAMP BRACKET

Fig. 1

_1, WARNING: The use of attachments or accessories not listed might be hazardous.

_l, WARNING: To prevent accidental starting that

could cause possible serious personal injury,

assemble all parts to your saw completely before

connecting it to power supply. Saw should never

be connected to power supply when you are

assembling parts, making adjustments, installing

or removing blades or accessories, or when not

in use.

WORK CLAMP

See Figure 2.

The worl_ clamp provides greater control by clamping

the workpiece to the fence. It also prevents the

workpiece from creeping toward the saw blade. This

is very I?elpful when cutting compound miters. To

install the work clamp, place the shaft of the clamp in

either hole in front of the miter table base. Rotate the

knob on the clamp to move it in or out as needed.

_, WARNING: Make sure the saw blade or blade

guard will not hit the work clamp assembly when

cutting 35 ° to 45° angles. Failure to heed this

warning can result in serious personal injury.

WORK

CLAMP

MITER TABLE BASE Fig. 2

DUST BAG

See Figure 3.

The dust bag fits over the exhaust port on the upper

blade guard. To install it, remove the dust guide from

the exhaust port. Then, squeeze the two metal clips to

open the mouth of the bag and slide it on the exhaust

port. Release the clips. The metal ring in the bag

should lock in between the grooves on the exhaust

port. For more efficient operation, empty dust bag

when no more than half full. This will permit better air

flow through the bag.

DUST BAG

EXHAUST PORT

Fig. 3

TABLE EXTENSIONS

See Figure 4.

To install table extensions, insert the ends of the

extensions into the holes in the sides of the base.

Secure them in place by positioning a clamp bracket

under each table extension beneath the miter table.

Orient each clamp bracket as shown in figure 4.

Secure each clamp bracket in place with a clamp

bracket screw. The clamp bracket screw threads

through the clamp bracket and tightens against

bottom of miter table, securing clamp bracket against

table extension.

SAWVIEWED

FROMBELOW

CLAMP

BRACKET

TABLEEXTENSION

Fig. 4

STOP BLOCK

See Figures 5 and 6.

The stop block is useful as a stop for cutting multiple

pieces to the same length. It can be installed on either

table extension on either side of the saw base:

• Slide the stop block on the back arm of either table

extension, then insert the table extension into the

saw base. See Figure 5.

• Use the small wing screw to secure the stop block

to the table extension. See Figure 5.

•Loosen the small wing screw and adjust the stop

block the desired distance from the blade for the

cut to be made.

STOPBLOCK

SMALL

WINGSCREW

MITERSAWBASE

EXTENSION Fig. 5

• Tighten small wing screw securely,

• Make a test cut in scrap material and measure the

length of the workpiece.

• Make any necessary adjustments.

_, WARNING: When using the work clamp with

the stop block, installthe clamp o_ the stop block

side of the blade. This will eliminate the

possibility of the saw catching the loose end and

kicking up. Failure to heed this warning can

result in serious personal injury.

STOP

BLOCK

Fig. 6

Autres manuels pour 315.212100

Ce manuel convient aux modèles suivants

Autres manuels Craftsman Scie

Craftsman

Craftsman 315.228310 Manuel utilisateur

Craftsman

Craftsman 21237 - 10 in. Sliding Miter Saw Manuel utilisateur

Craftsman

Craftsman 137.216100 Manuel utilisateur

Craftsman

Craftsman 172.2677 Manuel utilisateur

Craftsman

Craftsman 137.21825 Manuel utilisateur

Craftsman

Craftsman 315.220380 Manuel utilisateur

Craftsman

Craftsman 113.198510 Manuel utilisateur

Craftsman

Craftsman 901.23181 Manuel utilisateur

Craftsman

Craftsman 113.247410 Manuel utilisateur

Craftsman

Craftsman Professional 320.27224 Manuel utilisateur

Craftsman

Craftsman 113.196421 Manuel utilisateur

Craftsman

Craftsman 315.284610 Manuel utilisateur

Craftsman

Craftsman 113.23611t Manuel utilisateur

Craftsman

Craftsman 113.298722 Manuel utilisateur

Craftsman

Craftsman 10 IN. COMPOUND MITER SAW 315.23538 Manuel utilisateur

Craftsman

Craftsman Accra-Arm 113.29440 Fiche technique

Craftsman

Craftsman 125.46756 Manuel utilisateur

Craftsman

Craftsman 137.212150 Manuel utilisateur

Craftsman

Craftsman 21828 - Professional 10 in. Jobsite Saw Manuel utilisateur

Craftsman

Craftsman 113.29921 Manuel utilisateur

Craftsman

Craftsman 113.234650 Manuel utilisateur

Craftsman

Craftsman Contactor 113.236400 Manuel utilisateur

Craftsman

Craftsman 286.26829 Manuel utilisateur

Craftsman

Craftsman 124.3299 Manuel utilisateur

Manuels Scie populaires d'autres marques

RIDGID

RIDGID BS1400 Manuel utilisateur

ATIKA

ATIKA BWS 400-2 Manuel utilisateur

RGC

RGC FS20 Manuel utilisateur

Makita

Makita M2300 Manuel utilisateur

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manuel utilisateur

IMET Spa

IMET Spa SIRIO 370 AF-E Manuel utilisateur

Optimum

Optimum OPTisaw CS 275 Manuel utilisateur

Makita

Makita BPB180 Manuel utilisateur

Stihl

Stihl MS 462 C-M Manuel utilisateur

AEG

AEG TS 250 K Manuel utilisateur

Meec tools

Meec tools 004665 Manuel utilisateur

Makita

Makita LS1018L Manuel utilisateur

Ryobi

Ryobi RCS1400 Manuel utilisateur

DeWalt

DeWalt DCS391 Manuel utilisateur

Sealey

Sealey SA72 Manuel utilisateur

skilsaw

skilsaw SPT88 Instructions de montage

Urrea

Urrea SI810 Dimensions et guide d'installation

EINHELL

EINHELL BKG 210/1 Manuel utilisateur