Cotek CR-21 PLUS Manuel utilisateur

1. Introduction

1-1. System

The remote is designed to easily and quickly connect Cotek SR-1600 Plus.

The LCD display is used for setting up the inverter, as well as displaying current

status or fault messages. Pressing buttons allows you to select a menu item or

to save a setting, once it is displayed on the LCD screen.

Description

Function

Scroll up

DOWN

Scroll down

ESC

Go back to previous page.

ENTER

Enter next page and save setting value

RJ-45 port

Connect to the Inverter

Front and rear Panel introduction

User Guide For CR-21 PLUS Remote Control

1-2. Mechanical Drawings

Unit: mm

1-3. Hardware Installation

2. Display tree

Power Switch

INVERTER

Initialization..

GRID-->SR-->LOAD

BAT-------^ Major

2-1

User Interface

2-3

LCD Contrast

2-3-1

LCD Auto-off

2-3-2

Baudrate

2-3-3

DRY C Setting

2-3-4

Alarm Setting

2-3-5

DateTime Setting

2-3-6

Password Setting

2-3-7

Output On/Off

2-3-8

Bat Parameter

2-4

OVP Setting

2-4-1

OVP Recovery

2-4-2

UVP Setting

2-4-3

UVP Recovery

2-4-4

UV Alarm

2-4-5

AC Parameter

2-5

O/P Voltage

2-5-1

O/P Frequency

2-5-2

Sync Frequency

2-5-3

AC or DC Mode

2-5-4

AC Sharing

2-5-5

AC OVP Setting

2-5-6

AC OVP Recovery

2-5-7

AC UVP Setting

2-5-8

AC UVP Recovery

2-5-9

Display Event

2-6

OUTPUT：

xxx.xV

xx.xHz xxx.xA

GRID：xxx.xV

xx.xHz xxx.xA

BATTERY：xxx.xV

discharging xxx.xA

STATUS：

2-2

OUTPUT

xxW xxVA

OUTPUT

xxW% xxVA%

Enter into System Setup by “press for 3 seconds”

2-1 GRID-->SR-->LOAD BAT-------^ Major

The connection status and Alarm type. For the description of alarm type, (Major /

Minor Alarm) please refer to Alarm List in the “SR-1600 Plus User Manual.”

2-2 STATUS：

STATIS

Possible Cause

Normal

The machine is working normally

Machine Abnormal

Parallel Fault or Module Fault

Grid Abnormal

AC source abnormal

Fan Fault

Fan does not work

BAT. Low

Under DC voltage protevtion

BAT. High

Over DC voltage protection

Over Load

The system over the rated capacity(OLA >15sec)

Redundancy Fault

Remove the redundancy module or redundant module failure

Over Temperature

Temperature is too high

BAT. LowAlarm

Under DC voltage Alarm

BAT. High Alarm

Over DC voltage Alarm

Over Load Alarm

The system over the rated apacity(OLA)

Major Relay On

Pin 12~13 voltage keep high(485 board)

Minor Relay On

Pin 14~13 voltage keep high(485 board)

Remote OFF

Turn off the machine from dry contact pin1& pin2

2-3 User Interface

※The first time use the setting interface, must enter password (000000).

2-3-1 LCD contrast : Sets the LCD screen contrast.

Default = 50% Setting range = 0% ~ 100%

Setting Menu

SETT<value>

LCD Contrast

0 ~ 100

2-3-2 LCD Auto-off : Sets the LCD screen backlight auto off timer

Default = 120 seconds Setting range = 0 ~ 120 seconds

Setting Menu

SETT<value>

LCD Auto-off

0 ~ 120

2-3-3 Baud rate : Default setting：4800

Setting Menu

SETT<value>

RS-485

Baud rate

1200

2400

4800

9600

19200

2-3-4 Dry contact C setting : Default =1, Setting range = 0~2, default=1.

Setting Menu

SETT <value>

Description

Dry C setting

Disable

DRY C for Major

Selectable extra alarm to

go with Major

DRY C for Minor

Selectable extra alarm to

go with Minor alarm

2-3-5 Alarm Setting: Default =1

Setting Menu

SETT <value>

Description

Alarm Setting

Normal

Mute

Mute all alarms

One time

Silent warning for current

status

2-3-6 Date Time Setting: Date yyyy-mm-dd Time hh-mm-ss

YY :year MM :month DD :date HH :hour MM :minute SS :second

2-3-7 Password Setting: 000000~999999, default setting:000000

2-3-8 Output On/Off:

Setting Menu

SETT <value>

Description

Output On/Off

Turn on the output

Off

Turn off the output

2-4 Bat Parameter

2-4-1 OVP Setting : Set the Over Voltage Protection (OVP) and shutdown.

Default = 34 VDC @ 24V Model. 68 VDC @ 48V Model

Model

Setting value range

24V

30 VDC ~ 34 VDC

48V

60 VDC ~ 68 VDC

2-4-2 OVP Recovery : When the DC input voltage is higher than the OVP

setting, the SR series shuts down; once the input voltage falls below the set OVP

value, the SR series will automatically restart.

Default = 28 VDC @ 24V Model. 56 VDC @ 48V Model

Model

Setting value range

24V

26 VDC ~ 30 VDC

48V

52 VDC ~ 60 VDC

2-4-3 UVP Setting : Setting Under Voltage Protection (UVP) and shutdown on

the inverter operation. Default= 18 VDC @ 24V Model. 36VDC @ 48V Model

Model

Setting value range

24V

18 VDC ~ 25 VDC

48V

36 VDC ~ 50 VDC

2-4-4 UVP Recovery : When the DC input voltage is below the set UVP value,

the SR series shuts down; once the input voltage rises above the set UVP

value, the SR series will automatically restart.

Default= 25 VDC @ 24V Model. 50VDC @ 48V Model

Model

Setting value range

24V

23 VDC ~ 27 VDC

48V

46 VDC ~ 54 VDC

2-4-5 UV Alarm : Setting Under Voltage (UV) alarm. When the input voltage is

lower than the set value, the SR series will sound a “beep” to remind you that the unit

is going to shutdown. Default= 21 VDC @ 24 V Model. 42 VDC @ 48 V Model

Model

Setting value range

24V

19 VDC ~ 26 VDC

48V

38 VDC ~ 52 VDC

2-5 AC Parameter

2-5-1 O/P Voltage : Setting the SR series output voltage on the inverter

operation. 1xx = 100V, 110V, 115V or 120V ; 2xx = 200V, 220V, 230V or 240V.

Model

Setting value range

1XX

97 VAC ~ 127 VAC

2XX

194 VAC ~ 254 VAC

2-5-2 O/P Frequency : Setting the SR series output frequency on the inverter

operation. 1xx = 100V, 110V, 115V or 120V ; 2xx = 200V, 220V, 230V or 240V.

Model

Setting value range

1XX & 2XX

50 or 60 Hz

2-5-3 Sync Frequency : Setting SR series output frequency tolerance range on the

inverter operation. 1xx = 100V, 110V, 115V, 120V ; 2xx = 200V, 220V, 230V or 240V.

Model

Setting value range

1XX & 2XX

0 Hz ~ 3 Hz

2-5-4 AC or DC Mode : Default =1,AC Mode is the 1st priority source.

DC Mode：DC is the 1st priority source, and the AC power is the 2nd priority source.

AC Mode：AC is the 1st priority source, and the DC power is the 2nd priority source.

Mode Priority

SETT<value>

DC Mode

AC Mode

2-5-5 AC Sharing : Setting range = 10, 20, 30, 40, 50, 60, 70, 80, 90, 100

Default= 100 (Disable)

Setting Menu

SETT<value>

Description

AC Ratio

AC load 10%, DC load 90%

AC load 20%, DC load 80%

AC load 30%, DC load 70%

AC load 40%, DC load 60%

AC load 50%, DC load 50%

AC load 60%, DC load 40%

AC load 70%, DC load 30%

AC load 80%, DC load 20%

AC load 90%, DC load 10%

100

Disable

2-5-6 AC OVP Setting : Set the Grid Over Voltage Protection (OVP) and transfer

to DC mode(or shuts down without battery).

Default = 130 VAC @ 1xx Model. 260 VAC @ 2xx Model

Model

Setting value range

1xx

127.5 VAC ~ 132.5 VAC

2xx

255 VAC ~ 260 VAC

2-5-7 AC OVP Recovery : When the AC input voltage is higher than the OVP

setting, the SR series transfer to DC mode(or shuts down without battery); once the

input voltage falls below the set AC OVP recovery value, the SR series will

re-operate in AC mode. Default = 125 VAC @ 1xx Model. 150 VAC @ 2xx Model

Model

Setting value range

1xx

120 VAC ~ 127 VAC

2xx

240 VAC ~254 VAC

2-5-8 AC UVP Setting : Set the Grid Under Voltage Protection (UVP) and transfer

to DC mode(or shuts down without battery).

Default= 90 VAC @ 1xx Model. 180VAC @ 2xx Model

Model

Setting value range

1xx

75 VAC ~ 90 VAC

2xx

150 VAC ~ 180 VAC

2-5-9 AC UVP Recovery : When the AC input voltage is below the set UVP value, the

SR series transfer to DC mode(or shuts down without battery) ; once the input voltage rises

above the set UVP recovery value, the SR series will re-operate inAC mode.

Default= 95 VAC @ 1xx Model. 190VAC @ 2xx Model

Model

Setting value range

1xx

90.5 VAC ~ 100 VAC

2xx

181 VAC ~ 200 VAC

2-6 Display Event

2-6-1Display description

XXX (index) code:XXX (please refer to Error code List)

YY-MMDD-HH-MM-SS (Event time)

※Enter the event page the first information is the latest event

Model

Setting value range

Model

Setting value range

002

Output off

020

Under DC voltage protection

recovery

003

Output on

021

Under DC voltage protection

004

AC share off

022

Overload alarm recovery

005

AC share on

023

Overload alarm

006

AC mode off

024

Overload protection recovery

007

AC mode on

025

Overload protection

008

DC mode off

026

Fan normal

009

DC mode on

027

Fan failure

010

Grid Volt normal

028

Over temperature protection recovery

011

Grid Volt abnormal

029

Over temperature protection

012

Freq normal

030

The Machine was working

013

Freq abnormal

031

Component failed

014

Over DC voltage alarm

recovery

032

IC Power voltage normal

015

Over DC voltage alarm

033

IC Power voltage abnormal

016

Over DC voltage protection

recovery

034

Insert the module

017

Over DC voltage protection

035

Remove the module

018

Under DC voltage alarm

recovery

036

Redundancy _OK

019

Under DC voltage alarm

037

Redundancy_lost

No.33, Sec. 2, Renhe Rd., DaxiDist., Taoyuan City 33548, Taiwan

Phone：+886-3-3891999 FAX：+886-3-3802333

http：// www.cotek.com.tw

2019.03._A0

Error code list

Table des matières

Autres manuels Cotek Télécommande

Cotek

Cotek CR-1 Manuel utilisateur

Cotek

Cotek CR Series Manuel utilisateur

Cotek

Cotek CR-20 Manuel utilisateur

Cotek

Cotek CR5 Manuel utilisateur

Cotek

Cotek CR-10 Manuel utilisateur

Cotek

Cotek CR-20 Manuel utilisateur

Cotek

Cotek CR6 Manuel utilisateur

Cotek

Cotek CR8 Manuel utilisateur

Cotek

Cotek CR Series Manuel utilisateur

Cotek

Cotek CR Series Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation