Cornelius P/N 629083202 Manuel utilisateur

ED150 ‘’K’’ Style Lid Kit Installation Instructions

INSTALLATION INSTRUCTIONS

ED150 “K” STYLE LID KITS,

P/N 629083204 AND 629083202

Revision Date: April 18, 2011 www.cornelius.com Revision:D

These “K” style kits apply to the following ice maker:

WARNING:

Disconnect power to the unit before installing the adaptor following all lockout/tag out procedures established by the

user. Verify all the power is off to the unit before performing any work.

Failure to comply could result in serious injury, death or damage to the equipment.

WARNING:

All ice baffle plates and bin states, if included or recommended in this kit, must be installed as directed in this manual

or the equipment manufacturer’s instructions.

Failure to comply could result in serious injury, death or damage to the equipment.

WARNING:

All of the attachment screw and plates must be installed as directed in this manual.

Failure to comply could result in serious injury, death or damage to the equipment.

Table 1. Appropriate Model

Ice maker Width

Manitowoc Q320/420 22”

Table 2. Loose Shipped Parts

Item No. Part No. Name Catty.

1 52994 Cover, Gray (629083202) 1

52934 Cover, Black (629083204)

2620027505 DF150 Ice Maker Lid Assembly 1

3 620027306 Bracket 2

4 70217 #8 Screw 6

5 50904 RTV 1

6 90221 Label 1

7 620909401 Installation Instruction 1

8 620701902 Acorn Nut, 8-32 Nylon 2

9 620701901 Sealing Washer 2

10 620042928 Baffle Ice ED150 Adapter Lid 1

11 621701903 #8 Nylon Washer 2

ED150 ‘’K’’ Style Lid Kit Installation Instructions

1. Unpack the kit.

2. Insert a baffle assembly into the adapter lid.

3. Place (2) sealing washers (item 9) over studs and (2) flat washers (item11), then fasten in place with (2)

plastic acorn nuts (item 8).

4. Set ice maker lid on the top of the dispenser.

5. Using the slotted holes in the lid as a template, drill four (4) 9/64I diameter holes at the bottom of the slots

(see Detail A). Use extreme care not to drill into the hopper. Fasten the lid to the dispenser with four (4) #8

sheet metal screws, two on each side.

6. Seal the ice maker to the top of the dispenser as follows:

A. Run beads of RTV around the opening in the lid and inside of the perimeter of the ice maker outline so

that the ice maker sets on the RTV.

B. Set the ice maker onto the lid and position it as required.

C. Wipe away the excess RTV.

7. Remove the two rear screws (only) installed in step 5. Use those screws to install the mounting brackets

(item3). Drill 9/64I diameter holes into the ice maker cabinet using the bracket as a template. Use extreme

care not to drill into any ice maker components (condenser, tubing, etc.). Secure the brackets using the

screws provided.

8. Follow the ice maker manufacturers instruction to complete the installation of the ice maker including the

bin thermostat if so equipped or required.

9. If the plastic acorn nuts interfere with the positioning of the plastic manual fill cover, it may be necessary to

make small notches in the back flange of the cover to clear the acorn nuts.

CAUTION:

Bin Thermostat must not interfere with the agitator rotation.

ED150 ‘’K’’ Style Lid Kit Installation Instructions

Figure 1. Dispenser Assembly

ED150 ‘’K’’ Style Lid Kit Installation Instructions

Figure 2. ED150 Kit

ED150 ‘’K’’ Style Lid Kit Installation Instructions

View Z-Z

Figure 3. ED150 Kit Detail

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cornelius Machine à glaçons

Cornelius

Cornelius IACS224 Manuel utilisateur

Cornelius

Cornelius I Series Guide d'installation

Cornelius

Cornelius D3030-1 Manuel utilisateur

Cornelius

Cornelius Nordic CCM0322 Mode d’emploi

Cornelius

Cornelius 1400 Series Guide de configuration

Cornelius

Cornelius Nordic CCU0300 Series Mode d’emploi

Cornelius

Cornelius I Series Guide d'installation

Cornelius

Cornelius IRC630 Manuel utilisateur

Cornelius

Cornelius Series 200 Manuel utilisateur

Cornelius

Cornelius Enduro-300 IntelliCarb Manuel utilisateur

Cornelius

Cornelius DPT 230 Supplément

Cornelius

Cornelius P/N 620028801 Manuel utilisateur

Cornelius

Cornelius D3030 Manuel utilisateur

Cornelius

Cornelius CMP 600-30 Manuel utilisateur

Cornelius

Cornelius ED150 "K" Style Lid Kit Manuel utilisateur

Cornelius

Cornelius IDC215 Manuel utilisateur

Cornelius

Cornelius IMD300-15A Manuel utilisateur

Cornelius

Cornelius NORDIC ELITE Series Manuel utilisateur

Cornelius

Cornelius ICE MAKER Manuel utilisateur

Cornelius

Cornelius The Profile PR150 BC Manuel utilisateur

Cornelius

Cornelius XAC1444 Guide d'installation

Cornelius

Cornelius ED250 PRO GATE Caractéristiques techniques

Cornelius

Cornelius SPIRE 4.1 Manuel utilisateur

Cornelius

Cornelius Flavor Fusion 22127 Manuel utilisateur

Manuels Machine à glaçons populaires d'autres marques

Hoshizaki

Hoshizaki KMD-460MWJ Manuel utilisateur

Sub-Zero

Sub-Zero 315I Instructions d'utilisation

Unold

Unold 48945 Manuel utilisateur

Kenmore

Kenmore 2217402A Manuel utilisateur

GE XPIO43SCSS Manuel utilisateur

Hoshizaki

Hoshizaki KMD-901MAH Manuel utilisateur

Whynter

Whynter FIM-450HA Manuel utilisateur

U-Line

U-Line UMCR014-SC01A Manuel d'installation

Andrew James

Andrew James AJ000522 Manuel utilisateur

Scotsman

Scotsman CME1356 Manuel utilisateur

Scotsman

Scotsman ACM 25 Manuel utilisateur

Kärcher

Kärcher IP 120 Manuel utilisateur

U-Line

U-Line SS1095 Manuel utilisateur

Maytag

Maytag MIM1554WRS - Ice Maker Manuel utilisateur

Hoshizaki

Hoshizaki KM-630MAH Manuel utilisateur

Princess

Princess Yonanas Manuel utilisateur

Unold

Unold 48946 Manuel utilisateur

Electrolux

Electrolux E15IM60GP Manuel utilisateur