CORNEA CT1501 Manuel utilisateur
REPORT NO : HCT-F01-1002 FCC ID :PL4CT1501 DATE : OCTOBER 12, 2001
HYUNDAI CALIBRATION & CERTIFICATION TECHNOLOGIES CO., LTD.
SAN 136-1,AMI-RI , BUBAL-EUP, ICHEON-SI,KYOUNGKI-DO, 467-701,KOREA
TEL : +82 31 639 8518 FAX : +82 31 639 8525 www.hctec.co.kr
ATTACHMENT E.
-User’s Manual.
REPORT NO : HCT-F01-1002 FCC ID :PL4CT1501 DATE : OCTOBER 12, 2001
HYUNDAI CALIBRATION & CERTIFICATION TECHNOLOGIES CO., LTD.
SAN 136-1,AMI-RI , BUBAL-EUP, ICHEON-SI,KYOUNGKI-DO, 467-701,KOREA
TEL : +82 31 639 8518 FAX : +82 31 639 8525 www.hctec.co.kr
LCD MONITOR
MODEL: CT1501
CORNEA TECHNOLOGY CO ., Ltd.
U.S.A.
U.S.FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
INFORMATION TO THE USER
NOTE : This equipment has been tested and found to comply with the limits for a
Class B digital device pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet of a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for assistance.
Changes or modification not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Connecting of peripherals requires the use of grounded shielded signal cables.
TABLE OF CONTENTS
ADJUSTING YOUR LCD MONITOR --------------
2
• General safety precautions ………………….…………… 2
• Unpacking your monitor ………………………………… 5
• Viewing angle …………………………………………… 6
• Connecting your monitor …………………………… 7
• User controls……………………………………………… 8
• OSD Functions and adjustments ……………….…..……… 9
• Menu adjustments …………………………….…..……… 10
• Refining the picture ………………………….…..……… 12
APPENDIX -----------------------------------
-13
•Power management function …………….…..……..…… 13
•Video input terminal …………………………..……..…13
•Display modes ……………………………….………… 14
• Troubleshooting ………………………………………… 15
•Specifications …………………………………………… 17
Adjusting your lcd monitor
2
General safety precautions
This Monitor has been engineered and manufactured to assure your safety.Please
read this manual and comply with the warnings and the procedures to avoid any
serious electrical shock and other serious damage.
1.
2.
3.
4.
Do not place anythingheavy, wet or
magnetic on the monitor or power cord.
Do not cover the ventilation openings
nor touch them with metallic or
flammable material.
High temperature can cause troubles.
Avoid operating the monitor in extreme
heat, humidity or dusty areas. Extreme
temperature may cause discoloration or
damages.
Ambient Temperature : 0°C ~ 40°C
Do not use a solvent, such as benzene, to
clean the monitor to prevent any
damages to the LCD surface.
Do not use fine tools such as a pin or a
pencil near the monitor to prevent any
scratch to the LCD surface.
Adjusting your lcd monitor
3
5.
6.
7.
8.
Place the monitor on a flat surface to
prevent it from falling.
Do not apply any mechanical shocks to
the machine.
Install it in a well-ventilated area or
secure enough space for ventilation.
Turn the monitor off
before connecting it
to the power outlet.
Adjusting your lcd monitor
4
CAUTION : RISK OF ELECTRIC SHOCK, DO NOT OPEN
9.
1
0
.
11.
Make sure that the power cord and the
other cords are properly connected.
Overloaded AC outlets and extension
cords are dangerous. Also, the frayed
power cords and the broken plugs may
cause electric shock or fire.
Do not open the monitor. There are no
user-serviceable components inside.
There is a risk of exposure to high-
voltage electricity inside, even when
power is turned off. If the display
monitor does not operate properly,
unplug the power cord and contact your
dealer. Handling the electrical
equipment carelessly will cause a
serious electricalshock and other
hazards.
Adjusting your lcd monitor
5
Unpacking your monitor
Please make sure the following items are included with your monitor.
If you find that any of these itemsare missing or appeardamaged, contact your
dealer immediately.
The power cord can be different depending upon different voltage areas.
Adjusting your lcd monitor
6
Viewing angle
Your monitor was designed to allow you to adjust it to a comfortable viewing angle.
The viewing angle can be adjusted 6˚to 60˚forward and backward respectively as
indicated by the arrow marks below.
6?60?
Adjusting your lcd monitor
7
Connecting your monitor
Be sure to turn the computer off before connecting the monitor
?Connect the power adaptor cord to the monitor and then to the power supply.
?After powering on the computer, adjust the display using the various controls
provided. For further information on the installation procedure, please refer to
the operating guide of the computer being used.
Autres manuels pour CT1501
1
Table des matières
Autres manuels CORNEA Moniteur
