Coremorrow E70 Series Manuel utilisateur

4-Channel E70 Piezo Controller Software

User Manual

Version: V1.0

This document describes the following products:

■E70.C4K Piezo Controller Open loop 4 channels

■E70.D4S Piezo Controller SGS sensor 4 channels

1.Security ………………………………………………………………………………………………………………………… 1

1.1 Purpose ………………………………………………………………………………………………………………… 1

1.2 Safety instructions ………………………………………………………………………………………………… 1

1.3 User Manual Notes ………………………………………………………………………………………………… 2

2. Software purpose ………………………………………………………………………………………………………… 2

3. Software Installation …………………………………………………………………………………………………… 3

3.1 Serial Port Setup …………………………………………………………………………………………………… 3

3.2 USB Communication ……………………………………………………………………………………………… 4

4. Software Instruction …………………………………………………………………………………………………… 4

4.1 Point ……………………………………………………………………………………………………………………… 4

4.2 Waveform ……………………………………………………………………………………………………………… 5

4.3 Configuration ………………………………………………………………………………………………………… 7

4.4 System Settings ……………………………………………………………………………………………………… 7

4.5 Phase Control ………………………………………………………………………………………………………… 8

5.Contact us ………………………………………………………………………………………………………………… 11

Contents

1.Security

1.1 Purpose

The surface of 4-Channel E70 should be kept clean and dry, do't operate in humid or

static environment.

4-Channel E70 is used to drive capacitive loads (such as piezo actuator).

4-Channel E70 can't be used in the manuals of other products with the same name.

Pay attention to 4-Channel E70 can't be used to drive inductive or impedance loads.

4-Channel E70 can be used for static and dynamic operating applications

1.2 Safety instructions

4-Channel E70 is based on nationally recognized safety standards. Improper use may cause

personal injury or damage it. Operator is responsible for correct installation and operation

of it.

Please read the user manual in detail.

Please immediately eliminate any malfunctions and safety hazards caused by

malfunctions.

If the protective grounding wire is not connected or connected incorrectly, there will

be possibility of electric leakage. Maybe it will cause serious or even fatal injuries when

touch 4-Channel E70 at this time.

If open 4-Channel E70 privately, touching live parts may cause electric shock, resulting

in serious or even fatal injury or damage to the piezo controller.

Only authorized professional could open 4-Channel E70.

When opening 4-Channel E70, please disconnect the power plug.

Please do not touch any internal parts when operating in an exposed state.

4-Channel E70 Piezo Controller Software User Manual

1.3 User Manual Notes

The contents described in user manual are standard product descriptions, special

product parameters are not described in detail in this manual.

User manual is available for download on CoreMorrow website(www.coremorrow.

com).

When using 4-Channel E70, the user manual should be placed near the system for

easy reference in time. If the user manual is lost or damaged, please contact our customer

service department.

Please timely add all the information given in the manufacturer's user manual, such

as supplements or technical descriptions.

If your user manual is incomplete, it will miss a lot of important information, cause

serious or fatal injuries, and cause property damage. Please read and understood the

contents of the user manual before installing and operating 4-Channel E70.

Only authorized professionals who meet the technical requirements could install,

operate, maintain and clean 4-Channel E70.

2. Software purpose

Through the software to realize visual drive control of 4-Channel E70 piezo controller. The

software separately controls the functions of 4-Channel E70 through the classic single

point, classic waveform, classic configuration, analog array/open and closed loop settings,

and phase angle waveform functions to achieve convenient, intuitive and fast control

purposes.

3. Software Installation

3.1 Serial Port Setup

Notice! The serial port cable should be plugged and unplugged when the computer and

the piezo controller interface are closed or one end is closed, otherwise it may damage the

computer serial port or the serial chip of the controller interface!

Rear panel of 4-Channel E70 provides a 9-pin D-SUB connector (2/3/5 is serial port direct

connection, 6/7/8/9 is RS-422 communication interface, please refer to the user manual of

4-Channel E70 piezo controller for details).

Pleae use the serial cable provided by the manufacturer to connect 4-Channel E70 and the

PC, which could easily communicate with the PC through the terminal program.

If the PC has only one serial port, the default is COM1.

When the computer software is controlled through the RS-232 serial port, it could be

selected the serial port channel and baud rate on the software interface. Before connecting

the computer, please ensure that the COM port and baud rate are consistent with 4-Channel

E70. Otherwise, the connection fails.

Select the input mode of the controller as software control mode, switch the control switch

on the panel to M, turn on the computer, and run the interface software of the controller

for corresponding control. Please see section 4 for details.

3.2 USB Communication

3.2.1 Hardware requirement

Windows system computer.

4-Channel E70 piezo controller.

USB 2.0 connection cable.

Install the USB driver software when the above parts are working properly.

4-Channel E70 Piezo Controller Software User Manual

4. Software Instruction

4.1 Point

4-Channel E70 front panel provides a micro USB interface, please connect the PC and

4-Channel E70 through the USB cable, and then open the system.

Select the input mode of the controller as software control mode, switch the control switch

on the panel to M, turn on the computer, and run the interface software of the controller

for corresponding control. Please see section 4 for details.

CH1 send point data:

Select "Point", then click "Read Open/Closed-Loop Cordition ", fill in 10 in the edit box (10V

for open loop, 10μm/mrad for closed loop), and click "Send" to complete the send task.

Click "Stop" and the controller stops output.

Similarly, CH2, CH3, and CH44 send corresponding data.

1. Click"Read Open/Closed-Loop Condition"，read the open/closed loop data, and match

the piezo controller state.

2. Select "Single Channel High-Freq Control".

Single Channel high-freq, the frequency could be up to 1kHz~4kHz.

3. Click"Wave Type", select the send waveform, e.g. sine wave, square wave, triangular

wave, sawtooth wave.

4.2 Waveform

4. Fill in the data of P-P voltage, frequency, offset(usually half of the P-P voltage), waveform

transmission meets U2×f×C< Power.

4-Channel E70 Piezo Controller Software User Manual

5. Check the entered data values and click "Send". CH1 data waveform is sent.

6. Click the "Stop" to complete the waveform output stop.

4.3 Configuration

U = voltage, V

f = frequency, Hz

C = capacitance, F

4.4 System Settings

Click "Read System Information". After the data is transmitted from the piezocontroller

to the software, click "Save As Default" to complete the matching work between the

computer control software and the piezo controller. (Note: after the same computer read

system information read successfully and save as the default, when using the software

again, there is no need to carry out configuration, read system information and other

operations!)

Analog control: external analog signal control, at this time, the software control failure.

Digital control: software control, at this time, the analog control failure.

Switch to digital control: select the digital control from the drop down box, then click

"Start", the setting button lights up, click "Setting", complete the setting to the digital

control! Please see the figure below:

4-Channel E70 Piezo Controller Software User Manual

4.5 Phase Control

Phase control: the waveform and the frequency must be the same, P-P voltage and

offset could be different, phase Angle range from 0.0 to 360.0 degrees.

Phase wavefor control mode: select the waveform, then fill in the frequency, P-P voltage,

offset, phase angle and then fill in the related data of other channels, click" Send data"(this

time just store the waveform data value of the data to be sent to the piezo controller),

click"Start", the piezo controller receive the execution waveform sending command of the

trigger command.

Stop sending waveform: Click "Stop" to stop outputting the waveform.

Fill in the relevant data of the waveform to be sent:

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Coremorrow Contrôleurs

Coremorrow

Coremorrow E53.C Series Manuel utilisateur

Coremorrow

Coremorrow E63.A1K Series Manuel utilisateur

Coremorrow

Coremorrow Modular E70 Series Manuel utilisateur

Coremorrow

Coremorrow P87 Manuel utilisateur

Coremorrow

Coremorrow E53.B Series Manuel utilisateur

Coremorrow

Coremorrow E52 Series Manuel utilisateur

Coremorrow

Coremorrow E51.B3S Series Manuel utilisateur

Coremorrow

Coremorrow E63.C1K Series Manuel utilisateur

Coremorrow

Coremorrow E81.A1K Series Manuel utilisateur

Coremorrow

Coremorrow E51.D12S Series Manuel utilisateur

Coremorrow

Coremorrow E80.D3S-K Series Manuel utilisateur

Coremorrow

Coremorrow XE-650 Series Manuel utilisateur

Coremorrow

Coremorrow E71.D4E-H Manuel utilisateur

Coremorrow

Coremorrow E51.D7S Series Manuel utilisateur

Coremorrow

Coremorrow E00/E01 series Manuel utilisateur

Coremorrow

Coremorrow H01 Manuel utilisateur

Coremorrow

Coremorrow E82.C256K Series Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur