COOK SRSH-B Manuel utilisateur

1SRSH IO&M B51142-004

SRSH

Tamper Proof Centrifugal Exhauster

INSTALLATION, OPERATION AND MAINTENANCE MANUAL

Receiving and Inspection

Immediately upon receipt of an SRSH fan, carefully inspect

the fan and accessories for damage and shortage.

• Turn the wheel by hand to ensure it turns freely and does

not bind

• Check dampers (if included) for free operation of all moving

parts

• Record on the Delivery Receipt any visible sign of damage

Handling

Lift the fan by the lifting lugs provided under top cap.

NOTICE! Never lift by the shaft, motor or housing.

Storage

If the fan is stored for any length of time prior to installation,

completely ll the bearings with grease or moisture-inhibiting oil

(refer to Fan bearings, page 3). Store the fan in its original crate

and protect it from dust, debris and weather.

• Cover the inlet, and outlet opening to prevent the

accumulation of dirt and moisture in the housing

• Periodically rotate the wheel to keep a coating of grease on

all internal bearing parts

• Periodically inspect the unit to prevent damaging conditions

SRSH-B/SRSH-D

Rotating Parts & Electrical Shock Hazard:

Fans should be installed and serviced by qualied personnel

only.

Disconnect electric power before working on unit (prior to re-

moval of guards or entry into access doors).

Follow proper lockout/tagout procedures to ensure the unit

cannot be energized while being installed or serviced.

A disconnect switch should be placed near the fan in order

that the power can be swiftly cut o󰀨, in case of an emergency

and in order that maintenance personnel are provided com-

plete control of the power source.

Grounding is required. All eld-installed wiring must be com-

pleted by qualied personnel. All eld installed wiring must

comply with National Electric Code (NFPA 70) and all appli-

cable local codes.

Fans and blowers create pressure at the discharge and vac-

uum at the inlet. This may cause objects to get pulled into the

unit and objects to be propelled rapidly from the discharge.

The discharge should always be directed in a safe direction

and inlets should not be left unguarded. Any object pulled into

the inlet will become a projectile capable of causing serious

injury or death.

When air is allowed to move through a non-powered fan, the

impeller can rotate, which is referred to as windmilling. Wind-

milling will cause hazardous conditions due to unexpected ro-

tation of components. Impellers should be blocked in position

or air passages blocked to prevent draft when working on fans.

Friction and power loss inside rotating components will cause

them to be a potential burn hazard. All components should be

approached with caution and/or allowed to cool before con-

tacting them for maintenance.

Under certain lighting conditions, rotating components may

appear stationary. Components should be veried to be sta-

tionary in a safe manner, before they come into contact with

personnel, tools or clothing.

Failure to follow these instructions could result in death or se-

rious injury.

The attachment of roof mounted fans to the roof curb as well

as the attachment of roof curbs to the building structure must

exceed the structural requirements based on the environmen-

tal loading derived from the applicable building code for the

site. The local code o󰀩cial may require variations from the

recognized code based on local data. The licensed engineer

of record will be responsible for prescribing the correct attach-

ment based on construction materials, code requirements and

environmental e󰀨ects specic to the installation.

This publication contains the installation, operation and

maintenance instructions for standard units of the SRSH‑

B & SRSH‑D: Tamper Proof Centrifugal Roof Exhauster.

Carefully read this publication and any

supplemental documents prior to any

installation or maintenance procedure.

Loren Cook catalog, SRSH, provides additional information

describing the equipment, fan performance, available acces-

sories and specication data.

For additional safety information, refer to AMCA Publication

410 - 96, Safety Practices for Users and Installers of Industrial

and Commercial Fans.

All of the publications listed above can be obtained from:

• lorencook.com

• [email protected]

• 417-869-6474 ext. 166

For information and instructions on special equipment, con-

tact Loren Cook Company at 417-869-6474.

2SRSH IO&M B51142-004

Installation

If the fan was delivered with the motor unmounted, refer to

Belt and Pulley Installation, page 5.

Damper Installation

If your fan is supplied with dampers, follow the directions be-

low. If your fan does not include dampers, proceed to Belt and

Pulley Installation, page 5.

1. Place the damper inside the curb or inside the duct work. Ensure

the damper will open freely for the correct direction of the airow.

2. Secure to curb at the damper shelf.

3. Drill hole in the curb shelf for conduit needed for motor wiring.

4. Operate the dampers manually to ensure the blades move freely.

5. Install fan over curb while aligning the conduit location with the

conduit hole in the curb.

Wiring Installation

All wiring should be in accordance with local ordinances

and the National Electrical Code, NFPA 70. Ensure the power

supply (voltage, frequency, and current carrying capacity of

wires) is in accordance with the motor name-plate. Refer to

the Wiring Diagrams, page 3.

Leave enough slack in the wiring to allow for motor move-

ment when adjusting belt tension. Some fractional motors

have to be removed in order to make the connection with the

terminal box at the end of the motor.

Follow the wiring diagram included with the dis-

connect switch and the wiring diagram provid-

ed with the motor. Correctly label the circuit on

the main power box and always identify a closed

switch to promote safety (i.e., red tape over a

closed switch).

1. Lift hood assembly which covers the motor.

2. For internal wiring, run the electrical wire and conduit

through the opening drilled in the damper shelf (refer to

Damper Installation), then through the wiring conduit in

the ventilator base to the motor compartment.

3. For external wiring pull the wires through and complete

the wiring. For further information. Refer to Wiring Dia‑

grams, page 3.

Final Installation Steps

1. Ensure fasteners and set screws, particularly fan mounting

and bearing fasteners are tightened according to the recom-

mended torque shown in the table, Recommended Torque

for Setscrews/Bolts.

2. Inspect for correct amperage with an ammeter and correct

voltage with a voltmeter.

3. Ensure that all accessories are installed.

4. Test the fan to be sure the rotation is the same as indicated

by the arrow marked Rotation.

NOTICE! Do not allow the fan to run in the wrong

direction. This will overheat the motor and cause

serious damage. For 3-phase motors, if the fan is

running in the wrong direction, check the control

switch. It is possible to interchange two leads at

this location so that the fan is operating in the cor-

rect direction.

5. Inspect wheel-to-inlet clearance. Wheels may shift in ship-

ment. To realign wheel-to-inlet, shift upper bearing so there

is an equal radial clearance between the wheel and inlet. Re-

fer to Wheel to Inlet Clearance, page 6.

Operation

Pre-Start Checklist

1. Lock out all the primary and secondary power sources.

2. Inspect and tighten fasteners and setscrews, particu-

larly fan mounting and bearing fasteners Refer to Rec‑

ommended Torque chart.

3. Inspect belt tension and pulley alignment. Refer to Belt

and Pulley Installation, page 5.

4. Inspect motor wiring. Refer to Wiring Installation.

5. Ensure belt touches only the pulleys.

6. Rotate the wheel to ensure it rotates freely.

7. Ensure fan and duct work are clean and free of debris.

8. Close and secure all access doors.

9. Restore power to fan.

Start-up

Turn on the fan. In variable speed units, set the fan to its

lowest speed. Inspect for the following:

• Direction of rotation

• Excessive vibration

• Unusual noise

• Bearing noise

• Improper belt alignment or tension (listen for squealing)

• Improper motor amperage or voltage

NOTICE! If a problem is discovered, immediate-

ly shut the fan o. Lock out all electrical power

and check for the cause of the trouble. Refer to

Troubleshooting, page 5.

Inspection

Inspection of the fan should be conducted at the rst 30

minute, 8 hour and 24 hour intervals of satisfactory op-

eration. During the inspections, stop the fan and inspect

as instructed.

30 Minute Interval

Inspect bolts, setscrews, and motor mounting bolts. Ad-

just and tighten as necessary.

8 Hour Interval

Inspect belt alignment and tension. Adjust and tighten

as necessary.

24 Hour Interval

Inspect belt tension. Adjust and tighten as necessary.

Recommended Torque for Setscrews/Bolts (IN-LB)

Setscrews Hold Down Bolts

Size

Key Hex

Across

Flats

Recommended

Torque Size Recommended

Torque

Min. Max.

#8 5/64” 15 21 3/8”-16 324

#10 3/32” 27 33 1/2”-13 780

1/4 1/8” 70 80 5 /8”-11 1440

5/16 5/32” 140 160 3/4”-10 2400

3/8 3/16” 250 290 7/8”-9 1920

7/16 7/32” 355 405 1”-8 2700

1/2 1/4” 560 640 1-1/8”-7 4200

5/8 5/16” 1120 1280 1-1/4”-7 6000

3/4 3/8” 1680 1920 - -

7/8 1/2” 4200 4800 - -

19/16” 5600 6400 - -

3SRSH IO&M B51142-004

Wiring Diagrams

Single Speed, Single Phase Motor

T-

Ground B

Ground A

Line

When ground is required, attach to ground A or B with No. 6 thread

forming screw. To reverse, interchange T-1 and T-4.

2 Speed, 2 Winding, Single Phase Motor

Ground A

Ground B

T-1

T-

Low Speed

High Speed

Line

When ground is required, attach to ground A or B with No. 6 thread

forming screw. To reverse, interchange T-1 and T-4 leads.

Single Speed, Single Phase, Dual Voltage

Ground B

J-10

T-5

Ground A

Link A

Link B

Low Voltage

Line

Ground A

Link A & B

Line

Ground B

T-5

J-10

When ground is required, attach to ground A or B with No. 6 thread

forming screw. To reverse, interchange T-5 and J-10 leads.

Typical Damper Motor Schematic

Fan

Motor

Damper

Motor*

Second

Damper

Motor

ansformer** Transformer*

For 3 Phase, damper motor voltage should be the same between

L1and L2. For single phase application, disregard L3. *Damper mo-

tors may be available in 115, 230 and 460 volt models. The damp-

er motor nameplate voltage should be veried prior to connection.

**A transformer may be provided in some installations to correct the

damper motor voltage to the specied voltage.

3 Phase, 9 Lead Motor

456

L1L2L3

456

789

12 3

L1L2L3

Low Voltage

208/230 Volts

High Voltage

460 Volts

3 Phase, 9 Lead Motor

Y-Connection

6789

456

12 3

Low Voltage

208/230 V

olts

High V

oltage

460 Volts

L1L3

3 Phase, 9 Lead Motor

Delta-Connection

To reverse, interchange any two line leads.

2 Speed, 1 Winding, 3 Phase Motor

Motor

Together

High Speed

Line

Open

Low Speed

Line

Motor

To reverse, interchange any two line leads. Motors require magnetic

control.

2 Speed, 2 Winding, 3 Phase

Low Speed

High Speed

Motor

T12

T11

Line

To reverse:

High Speed - interchange leads T11 and T12.

Low Speed - interchange leads T1and T2.

Both Speeds - interchange any two line leads.

Maintenance

Establish a schedule for inspecting all parts of the fan. The

frequency of inspection depends on the operating conditions

and location of the fan.

Inspect fans exhausting corrosive or contaminated air within

the rst month of operation. Fans exhausting contaminated air

(airborne abrasives) should be inspected every three months.

Regular inspections are recommended for fans exhausting

non-contaminated air.

It is recommended the following inspections be conduct-

ed twice per year:

• Inspect bolts and setscrews for tightness. Tighten as

necessary. Refer to Torque chart

• Inspect belt wear and alignment. Replace worn belts with

new belts and adjust alignment as needed. Refer to Belt and

Pulley Installation, page 5

• Bearings should be inspected as recommended in the

Conditions Chart, page 4

• Inspect for cleanliness. Clean exterior surfaces only.

Removing dust and grease on motor housing assures

proper motor cooling

Fan Bearings

The fan bearings are provided prelubricated. Any special-

ized lubrication instructions on fan labels supersedes informa-

tion provided herein. Bearing grease is a petroleum lubricant

in a lithium base conforming to an NLGI #2 consistency. If

user desires to utilize another type of lubricant, they take re-

sponsibility for ushing bearings and lines, and maintaining a

lubricant that is compatible with the installation.

4SRSH IO&M B51142-004

An NLGI #2 grease is a light viscosity, low-torque, rust-in-

hibiting lubricant that is water resistant. Its temperature range

is from -30°F to 200°F and capable of intermittent highs of

25 0 ° F.

Bearings should be prelubricated in accordance with the fol-

lowing conditions chart.

Conditions Chart

RPM Temp °F Greasing Interval

Up to 1000 -30 to 120 3 months

120 to 200 1 month

1000 to 3000 -30 to 120 6 weeks

120 to 200 2 weeks

Over 3000 -30 to 120 2 weeks

120 to 200 1 week

Any Speed < -30 Consult Factory

Any Speed > 200 1/2 week

For moist or otherwise contaminated installations, divide the interval

by a factor of three.

For best results, lubricate the bearing while the fan is in

operation. Pump grease in slowly until a slight bead forms

around the bearing seals. Excessive grease can damage the

seal and reduce the life through excess contamination and/or

loss of lubricant.

In the event that the bearing cannot be seen, use no more

than three injections with a hand operated grease gun.

Lubricants

Loren Cook Company uses petroleum lubricant in a lithium

base conforming to NLGI grade 2 consistency. Other grades

of grease should not be used unless the bearings and lines

have been ushed clean. If another grade of grease is used, it

should be lithium-based.

An NLGI grade 2 grease is a light viscosity, low-torque,

rust-inhibiting lubricant that is water resistant. Its tempera-

ture range is from -30°F to +200°F and capable of intermittent

highs of +250° F.

Motor Bearings

Motors are provided with prelubricated bearings. Any lubri-

cation instructions shown on the motor nameplate supersede

the following instructions.

Direct Drive 1050/1075, 1200, 1300 & 1500 RPM units use

a prelubricated sleeve bearing that has a oil saturated wicking

material surrounding it. The initial factory lubrication is ade-

quate for up to 10 years of operation under normal conditions.

However, it is advisable to add lubricant after 3 years. Use

only LIGHT grade mineral oil or SAE 10W oil up to 30 drops.

If the unit has been stored for a year or more it is advisable to

lubricate as directed above.

Motors without sleeve bearings (as described above) will

have grease lubricated ball or roller bearings. Motor bearings

without provisions for relubrication will operate up to 10 years

under normal conditions with no maintenance. In severe ap-

plications, high temperatures or excessive contaminates, it is

advisable to have the maintenance department disassemble

and lubricate the bearings after three years of operation to

prevent interruption of service.

For motors with provisions for relubrication, follow intervals

of the table below.

Relubrication Intervals

Service

Conditions

Nema Frame Size

Up to and

Including 184T 213T-365T 404T and Larger

1800

RPM &

Less

Over

1800

RPM

1800

RPM &

Less

Over

1800

RPM

1800

RPM &

Less

Over

1800

RPM

Standard 1-1/2 yrs. 3 mos. 1 yr. 3 mos. 6 mos. 6 wks.

Service 6 mos. 6 wks. 6 mos. 6 wks. 3 mos. 2 wks.

For units in severe conditions, lubrication intervals should be re-

duced to half.

Motors are provided with a polyurea mineral oil NGLI #2

grease. All additions to the motor bearings are to be with

a compatible grease such as Exxon Mobil Polyrex EM and

Chevron SRI.

Motor Services

Should the motor prove defective within a one-year period,

contact your local Loren Cook representative or your nearest

authorized electric motor service representative.

Changing Shaft Speed

All belt driven ventilators (5HP or less) are equipped with

variable pitch pulleys. To change fan speed, perform the fol-

lowing:

1. Loosen setscrew on driver (motor) pulley and remove key,

if equipped.

2. Turn the pulley rim to open or close the groove facing. If

the pulley has multiple grooves, all must be adjusted to

the same width.

3. After adjustment, inspect for proper belt tension.

Speed Reduction

Open the pulley in order that the belt rides deeper in the

groove (smaller pitch diameter).

Speed Increase

Close the pulley in order that the belt rides higher in the

groove (larger pitch diameter). Ensure that the RPM limits of

the fan and the horsepower limits of the motor are maintained.

Maximum RPM

SRSH

Size

Maximum

RPM

60 -100 2125

120 1715

135 1620

150 1550

165 1325

180 1535

195 1370

210 1210

225 1060

245 900

270 765

5SRSH IO&M B51142-004

Replacing Pulleys and Belts

1. Clean the motor and fan shafts.

2. Loosen the motor plate mounting bolts to relieve the belt

tension. Remove the belt.

3. Loosen the pulley setscrews and remove the pulleys from

the shaft. If excessive force is required to remove the pul-

leys, a three-jaw puller can be used. This tool, however,

can easily warp a pulley. If the puller is used, inspect the

trueness of the pulley after it is removed from the shaft.

The pulley will need replacement if it is more than 0.020

inch out of true.

4. Clean the bores of the pulleys and place a light coat of oil

on the bores.

5. Remove any grease, rust or burrs from pulleys.

6. Place the fan pulley on the fan shaft and the motor pulley

on the motor shaft. Damage to the pulleys can occur when

excessive force is used in placing the pulleys on their re-

spective shafts.

7. After the pulleys have been correctly placed back onto

their shafts, tighten the pulley setscrews.

Belt and Pulley Installation

Belt tension is determined by the sound of the belts when

the fan is rst started. The belts will produce a loud squeal,

which dissipates after the fan is operating at full capacity. If

belt tension is too tight or too loose, lost e󰀩ciency and dam-

age may occur.

1. Loosen motor plate adjustment bolts and slide motor plate

so that belts easily slip into the grooves on the pulleys.

Never pry, roll, or force the belts over the rim of the pulley.

2. Slide motor plate until proper tension is reached. For prop-

er tension, a deection of approximately 1/4” per foot of

center distance should be obtained by rmly pressing the

belt. Refer to Figure 1.

3. Lock the motor plate adjustment bolts in place

4. Ensure pulleys are properly aligned. Refer to Figure 2.

Pulley Alignment

Pulley alignment is adjusted by loosening the motor pulley

setscrew and by moving the motor pulley on the motor shaft.

Figure 2 indicates where to measure the allowable gap for

the drive alignment tolerance. All contact points (indicated by

WXYZ) are to have a gap less than the tolerance shown in the

table. When the pulleys are not the same width, the allowable

gap must be adjusted by half of the di󰀨erence in width. Figure

3illustrates using a carpenter’s square to adjust the position

of the motor pulley until the belt is parallel to the longer leg of

the square.

Tolerance

Center

Distance

Maximum

Gap

Up thru 12” 1/16”

12” up

through 48” 1/8”

Over 48” 1/4”

OFFSET ANGULAR OFFSET/ANGULAR

CENTER

DISTANCE

(CD)

GAP

Bearing Replacement

The fan bearings are pillow block

type ball bearings.

1. Remove the old bearing.

2. Remove any burrs from the

shaft by sanding.

3. Slide new bearings onto the

shaft to the desired location Fig‑

ure 3 and loosely mount bear-

ings onto the bearing support.

Bearing bolts and setscrews

should be loose enough to allow

shaft positioning.

4. Correctly position the wheel and

tighten the bearing bolts securely to the bearing support.

5. Align setscrews bearing to bearing and secure tightly to

the shaft.

NOTICE! Never tighten both pairs of setscrews be-

fore securing bearing mounting bolts. This may

damage the shaft.

6. Inspect the wheel position again. If necessary, readjust

by loosening the bearing bolts and setscrews and repeat

from step 5.

Wheel Replacement

1. Drill two holes approximately centered between the shaft

and the edge of the hub OD with the following dimensions:

• 1/4” diameter

• 3/8” to 1/2” deep

• 180° apart in face of hub

2. Tap 1/4” holes to 5/16” thread with the 5/16” hole tap. Do

not drill or tap any larger than recommended.

3. Screw the puller arms into the tapped holes full depth of

threads (3/8” to 1/2” approximately). Align center of pull-

er with center of shaft. Make certain all setscrews in hub

(normally a quantity of two) are fully removed. Work puller

slowly to back wheel o󰀨 the shaft.

Figure 1

Figure 2

1 foot

1/4 inch

6SRSH IO&M B51142-004

Recommended Puller

Lisle No. 45000 Steering Wheel Puller. This puller is avail-

able at most automotive parts retail outlets.

Wheel PullerDrilled Hole Location

Wheel-to-Inlet Clearance

The correct wheel-to-inlet clearance is critical to proper fan

performance. This clearance should be veried before initial

start-up since rough handling during shipment could cause a

shift in fan components. Refer to wheel/inlet drawing for cor-

rect overlap.

Adjust the overlap by loosening the wheel hub and moving

the wheel along the shaft to obtain the correct value.

A uniform radial gap (space between the edge of the cone

and the edge of the inlet) is obtained by loosening the inlet

cone bolts and repositioning the inlet cone.

Size Overlap

100 - 195 5/8”

210 - 270 3/4”

300 - 445 1”

450 - 730 1-1/4”

OVERLAP

RADIAL

CLEARANCE

WHEEL SHROUD

INLET

Troubleshooting

Problem and Potential Cause

Low Capacity or Pressure:

• Incorrect direction of rotation. Make sure the fan rotates

in same direction as the arrows on the motor or belt drive

assembly

• Poor fan inlet conditions. There should be a straight clear

duct at the inlet

• Improper wheel alignment

Excessive Vibration and Noise:

• Damaged or unbalanced wheel

• Belts too loose; worn or oily belts

• Speed too high

• Incorrect direction of rotation. Make sure the fan rotates

in same direction as the arrows on the motor or belt drive

assembly

• Bearings need lubrication or replacement

• Fan surge

Overheated Motor:

• Motor improperly wired

• Incorrect direction of rotation. Make sure the fan rotates

in same direction as the arrows on the motor or belt drive

assembly

• Cooling air diverted or blocked

• Improper inlet clearance

• Incorrect fan RPMs

• Incorrect voltage

Overheated Bearings:

• Improper bearing lubrication

• Excessive belt tension

7SRSH IO&M B51142-004

SRSH-B Parts List

Hood shown open for clarity

Part No. SRSH-B Parts Description Part No. SRSH-B Parts Description

1Hood Assembly 9Power Assembly

2 Locking Hasp 10 Bearings (2)

3 Door Stay Rail (2) 11 Shaft

4 Door Stay Strut (2) 12 Driven Sheave

5 Base Assembly with Skirt 13 Drive Sheave

6Down Conduit 14 Belt

7 Motor Tray 15 Wheel (not shown)

8Isolator (4)

8SRSH IO&M B51142-004

SRSH-D Parts List

Hood sh

own open for clarity

Part No. SRSH-B Parts Description Part No. SRSH-B Parts Description

1Hood Assembly 6Down Conduit

2 Locking Hasp 7 Motor Tray

3 Door Stay Rail (2) 8Motor Isolator Assembly (4)

4 Door Stay Strut (2) 9Motor

5 Base Assembly with Skirt 10 Wheel (not shown)

September 2020

Limited Warranty

Loren Cook Company warrants that your Loren Cook fan was manufactured free of defects in materials and workmanship, to the extent stated herein.

For a period of one (1) year after date of shipment, we will replace any parts found to be defective without charge, except for shipping costs which will be

paid by you. This warranty is granted only to the original purchaser placing the fan in service. This warranty is void if the fan or any part thereof has been

altered or modied from its original design or has been abused, misused, damaged or is in worn condition or if the fan has been used other than for the

uses described in the company manual. This warranty does not cover defects resulting from normal wear and tear. To make a warranty claim, notify Loren

Cook Company, General O󰀩ces, 2015 East Dale Street, Springeld, Missouri 65803-4637, explaining in writing, in detail, your complaint and referring to

the specic model and serial numbers of your fan. Upon receipt by Loren Cook Company of your written complaint, you will be notied, within thirty (30)

days of our receipt of your complaint, in writing, as to the manner in which your claim will be handled. If you are entitled to warranty relief, a warranty ad-

justment will be completed within sixty (60) business days of the receipt of your written complaint by Loren Cook Company. This warranty gives only the

original purchaser placing the fan in service specically the right. You may have other legal rights which vary from state to state. For fans provided with