ControlFreq K200-3G Manuel utilisateur

K200-3G

3G GSM INTERCOM FOR UP TO 200 WAY

COMPLETE MANUAL

Contents TOC \t "Naslov 1, 1,Naslov 2, 2"

1. FOR YOUR SAFETY PAGEREF _TOC \H 5

2. INTRODUCTION PAGEREF _TOC1 \H 6

3. FEATURES AND APPLICATIONS PAGEREF _TOC2 \H 7

4. START UP PAGEREF _TOC3 \H 8

5. LED DISPLAY PAGEREF _TOC4 \H 9

6. CLEAR ALL PROGRAMMED DATA FROM K200 PAGEREF _TOC5 \H 10

7. CONNECTING DIAGRAM PAGEREF _TOC6 \H 11

8. PROGRAMMING K200 PAGEREF _TOC7 \H 12

9. THE K200 PARAMETERS PAGEREF _TOC8 \H 13

1.1. ALARM SUPPORT PAGEREF _TOC9 \H 13

1.2. OUTPUT MANAGEMENT PAGEREF _TOC10 \H 17

1.3. SECURITY LEVEL - SL PAGEREF _TOC11 \H 19

1.4. PREPAID CARD CREDIT AND VALIDITY INFORMATION PAGEREF _TOC12 \H 20

1.5. SET-UP PARAMETERS PAGEREF _TOC13 \H 22

1.6. SMS MESSAGES EDITOR PAGEREF _TOC14 \H 25

1.7. INTERCOM PAGEREF _TOC15 \H 26

1.8. ADDITIONAL CALL / TRADE BUTTON PAGEREF _TOC16 \H 28

1.9. DIRECT ACCESS BY ENTERING PIN CODE PAGEREF _TOC17 \H 30

1.10. DIRECT ACCESS BY ENTERING TEMPORARY ACCESS CODES – SPIN - VIA ILLUMINATED KEYPAD

PAGEREF _TOC18 \H 31

1.11. CALLER ID RECOGNITION (CLIP), CALLER-IN FUNCTION PAGEREF _TOC19 \H 32

1.12. EVENT LOGGING PAGEREF _TOC20 \H 34

1.13. SPECIAL SMS COMMANDS PAGEREF _TOC21 \H 35

10. PRINT-OUT OF THE PARAMETERS PAGEREF _TOC22 \H 37

1.1. RECEIVE ALL PARAMETERS (PALL) PAGEREF _TOC23 \H 37

1.2. CHECK SW REVISION (PSW) PAGEREF _TOC24 \H 37

1.3. CHECK SIGNAL QUALITY (PSQ) PAGEREF _TOC25 \H 37

1.4. RECEIVE TELEPHONE NUMBERS (PTN) PAGEREF _TOC26 \H 37

1.5. RECEIVE LINKS (PLN) PAGEREF _TOC27 \H 37

1.6. RECEIVE INPUT PARAMETERS (PIN) PAGEREF _TOC28 \H 37

1.7. RECEIVE INPUT FILTER VALUE (PID) PAGEREF _TOC29 \H 37

1.8. RECEIVE OUTPUT FILTER VALUE (POD) PAGEREF _TOC30 \H 37

1.9. RECEIVE DELAY BEFORE DIAL VALUE (PDD) PAGEREF _TOC31 \H 37

1.10. RECEIVE ACCESS TELEPHONE NUMBERS (PSL) PAGEREF _TOC32 \H 38

1.11. RECEIVE OUTPUT PARAMETERS (POS) PAGEREF _TOC33 \H 38

1.12. RECEIVE ALL PROGRAMMED SMS MESSAGES (P#) PAGEREF _TOC34 \H 38

1.13. RECEIVE SET UP PARAMETERS VALUE (PPA) PAGEREF _TOC35 \H 38

1.14. RECEIVE CREDIT PARS PARAMETERS (PCREF) PAGEREF _TOC36 \H 38

1.15. RECEIVE ALL CLIP PARAMETERS (PCLP) PAGEREF _TOC37 \H 38

1.16. RECEIVE INTERCOM CALL GROUPS PARAMATERS PAGEREF _TOC38 \H 38

1.17. RECEIVE TRADE BUTTON PARAMETERS PAGEREF _TOC39 \H 39

Page PAGE 48

1.18. RECEIVE PIN ACCESS CODES (PPIN) PAGEREF _TOC40 \H 39

1.19. RECEIVE SPIN ACCESS CODES PARAMETERS (PSPIN) PAGEREF _TOC41 \H 39

1.20. STATE OF THE CREDIT FOR THE PREPAID CARD PAGEREF _TOC42 \H 39

1.21. STATE OF THE OUTPUTS (PORC) PAGEREF _TOC43 \H 40

1.22. MANUAL GSM MODULE RETARD (MRES) PAGEREF _TOC44 \H 40

1.23. RECEIVE STATUS OF INPUTS (INS) PAGEREF _TOC45 \H 40

1.24. RECEIVE K200 LOG PAGEREF _TOC46 \H 40

11. CHANGING PARAMETERS USING THE SMS COMMANDS PAGEREF _TOC47 \H 41

12. DEFAULT SETTINGS ON K200 PAGEREF _TOC48 \H 42

13. PARAMETERS PRINT-OUT COMMANDS PAGEREF _TOC49 \H 45

Page PAGE 48

Figures

Figure 1: K200 Connection Diagram……………….………………………………………………..…11

Figure 2: Input Connection diagram. 13

Figure 3: Output Connection diagram 17

Tables

Table 1: IN, ID and DD parameters 14

Table 2: IN, ID, DD parameters example 14

Table 3: Remote alarm reporting parameters 15

Table 4: Remote alarm reporting example 16

Table 5: DTMF control example 16

Table 6: Output management parameters 18

Table 7: Output management parameters example 18

Table 8: SL parameter 19

Table 9: SL parameter example 19

Table 10: Prepaid card validity parameters 21

Table 11: Prepaid card validity parameters example 21

Table 12: Set-up parameters. 24

Table 13: Set-up parameters example. 24

Table 14: Message parameters. 25

Table 15: Message parameters example. 25

Table 16: Intercom parameters. 26

Table 17: Intercom parameters example. 27

Table 18: Trade button parameters. 28

Table 19: Trade button example. 28

Table 20: Entering PIN code parameters. 29

Table 21: Entering PIN code example. 29

Table 22: Entering SPIN access code parameters 30

Table 23: Entering SPIN access codes example 30

Table 24: CLIP parameters. 31

Table 25: CLIP parameters example. 32

Table 26: LOG parameters. 33

Table 27: LOG parameters example. 33

Table 28: SMS commands. 34

Table 29: SMS commands example. 34

Table 30: SOLO-KP default settings. 41

Table 31: SOLO-KP parameters print out commands. 42

Page PAGE 48

1. FOR YOUR SAFETY

Read these simple guidelines. Not following them may be dangerous or illegal. Read the

complete user guide for further information.

SWITCH ON SAFELY

Do not switch the unit on when use of wireless phone is prohibited or when it may cause

interference or danger.

INTERFERENCE

All wireless phones and units may be susceptible to interference, which could aﬀect

performance.

SWITCH OFF IN HOSPITALS

Follow any restrictions. Switch the unit oﬀ near medical equipment.

SWITCH OFF IN AIRCRAFT

Follow any restrictions. Wireless devices can cause interference in aircraft.

SWITCH OFF WHEN REFUELING

Do not use the unit at a refueling point. Do not use near fuel or chemicals.

SWITCH OFF NEAR BLASTING

Follow any restrictions. Do not use the unit where blasting is in progress.

USE SENSIBLY

Use only in the normal position as explained in the product documentation. Do not touch

the antenna unnecessarily.

Page PAGE 48

2. INTRODUCTION

K200 is a simple GSM intercom communication system for multi apartments, that is

designed to ensure low-cost, reliable and single box solution for intercom application. It is

designed for unlimited range, wire free GSM intercom and CLIP support.

In addition K200 supports alarm detection, stay-alive messages, credit warning (PAYG:

supported on VF and O2 UK).

Page PAGE 48

3. FEATURES AND APPLICATIONS

Features:

⇒Built-in 4 band (2G) or 5 band (3G) GSM module

⇒Keypad call support (up-to 200 apartments)

⇒1 direct call / trade button

⇒Keypad Access entry support (by 4 digit PIN codes –up to 2000 codes are possible)

⇒Up to 100 temporary SPIN access codes

⇒2 alarm inputs (trade, press to exit, door open)

⇒2 relay outputs

⇒Up to 500 telephone numbers for CLIP support (400 + 100)

⇒Programming by USB cable with PC

⇒Programming by SMS

⇒Programming by Web server

⇒Anti-tampering input

Page PAGE 48

4. START UP

IMPORTANT

USE A MICRO SIM CARD (the middle size)

⇒Insert SIM card to be used for K200 in your personal mobile phone.

IMPORTANT

ERASE THE PIN CODE!

⇒Insert SIM card in K200 device. The unit must be switched OFF when you insert

the SIM!

⇒Connect inputs and outputs to K200.

⇒Connect the antenna to antenna connector.

⇒Connect power cable to K200 device

⇒Connect device to source power supply voltage.

⇒Wait until LED3 display is turned ON (Yellow) and LED1 (Blue) starts ﬂashing. This

is set in around 30 –45 seconds.

⇒K200 unit is now ready to operate.

IMPORTANT

Before sending any SMS commands to K200, the device must be in

normal operation mode!

NOTE

K200 device will “beep”in 15s interval until the device is not in normal

operation.

Page PAGE 48

5. LED DISPLAY

BLUE LED (LED1)

- Indicates the level of the GSM signal from 1 to 5 LED ﬂashes (1 is weak signal, 5 is

excellent signal)

RED LED (LED2)

- When LED 2 is ON the unit has a problem with a GSM network connection or the

GSM part of the unit is out of order. In this case immediately call the service!

YELLOW LED (LED3)

- Short ﬂashing indicates that the GSM module is ON, but it is not yet connected on

the GSM network. After connection, Yellow LED is ﬂashing with short pulse ON and

a long pulse OFF.

Page PAGE 48

6. CLEAR ALL PROGRAMMED DATA FROM K200

This is highly recommended when a SIM card you are going to use for the K200 is not

new and it already has some data stored in the phone book memory.

By sending this SMS to K200 all programmed parameters and numbers are cleared:

;SDCLR;

After sending SMS you should wait at least 30 second for the command to be executed!

NOTE

By sending this command to the K200 all programmed data are erased from the SIM

card and from the memory inside the K200 device!

Page PAGE 48

Table des matières

Autres manuels ControlFreq Système d'interphone

ControlFreq

ControlFreq QUICK-FIT Manuel utilisateur

Manuels Système d'interphone populaires d'autres marques

Bticino

Bticino LINEA 3000 Manuel utilisateur

MSI

MSI MSI-140 Manuel utilisateur

golmar

golmar Stadio Plus Manuel utilisateur

CyberData

CyberData 011211 series Manuel

Vidos

Vidos duo M1021 Manuel utilisateur

Vimar

Vimar ELVOX 7539/E Manuel utilisateur

SSS Siedle

SSS Siedle BTSV 850-03 Manuel utilisateur

Dahua

Dahua VTO Series Manuel utilisateur

Elvox

Elvox 5651 Manuel utilisateur

Videx

Videx VIDEOKIT Series Manuel utilisateur

Rocom

Rocom Doortello Business FW T2.05W2.04 Manuel utilisateur

Viking

Viking E-35-EWP Manuel utilisateur

Safeguard Supply

Safeguard Supply LRA-EX1000 Manuel utilisateur

SSS Siedle

SSS Siedle BFCV 850 Series Manuel utilisateur

GRD

GRD MAX V2 Manuel utilisateur

Alecto

Alecto ADI-250 Manuel utilisateur

Aiphone

Aiphone IE-8MD Manuel utilisateur

Perel

Perel EDB4 Manuel utilisateur