Conrad Electronic FAZ3000-FB-2 Manuel utilisateur
Version 01/07
FAZ3000-FB-2
Wireless remote control
Item no. 75 08 43
This user manual belongs to this product. It contains important
information specific to its operation and handling. Please bear this in
mind when passing on the product to a third party.
Therefore keep this user manual for future reference!
A contents list can be found in the table of contents on page 3.
OPERATING INSTRUCTIONS
2
Introduction
Dear customer,
Thank you for purchasing this product.
This product meets the requirements of both current national and
European guidelines.
In order to ensure continued fulfilment of legal requirements and safe operation
of this product, we kindly ask you to carefully follow the instructions in this
user manual!
Please read the user manual completely and observe the safety and operation
instructions before using the product!
All company and product names contained herein are trademarks of their
respective owners. All rights reserved.
Should you have any further questions, please contact our technical
service:
Germany: Tel. no.: +49 9604 / 40 88 80
Fax. no.: +49 9604 / 40 88 48
Email: [email protected]
Mon. to Thur. 8.00am to 4.30pm
Fri. 8.00am to 2.00pm
3
Table of contents
Page
1. Prescribed use ...................................................................................... 4
2. Scope of delivery ................................................................................. 4
3. Explanation of icons ............................................................................. 4
4. Safety instructions ............................................................................... 5
a) General information ........................................................................ 5
b) Handling the batteries ..................................................................... 6
5. General information .............................................................................. 7
6. Controls ................................................................................................ 8
a) Normal button functions ................................................................ 8
b) Special function ‘attack alarm’ ...................................................... 9
7. Inserting the batteries, entering the security code ........................... 10
8. Registering the remote control to the ‘FAZ-Z’ alarm base station ... 12
9. Deleting a remote control from the ‘FAZ-Z’ alarm bas station ........ 14
10. Information on the range ................................................................... 16
11. Handling .............................................................................................. 17
12. Maintenance and cleaning .................................................................. 18
13. Disposal .............................................................................................. 19
a) General information ...................................................................... 19
b) Battery/rechargeable battery disposal ........................................ 19
14. Technical specifications ..................................................................... 20
15. Brief instructions ................................................................................ 21
a) Registering the remote control in the alarm base station ........... 21
b) Replacing the batteries of the remote control ............................ 21
c) Deleting a remote control from the alarm base station .............. 21
16. Declaration of conformity (DOC) ...................................................... 22
4
1. Prescribed use
The ‘FAZ3000-FB-2’ wireless remote control is a part of the ‘FAZ3000’ wireless
alarm system.
The ‘FAZ3000-FB-2’ wireless remote control is used to activate/deactivate the
‘FAZ-Z’ alarm base station (toggle between ‘disarmed’, ‘internally armed’ and
‘externally armed’).
It also has a panic function that can trigger an alarm using the ‘FAZ-Z’ alarm
base station.
Any use other than the one described above may damage the ‘FAZ3000-FB-
2’ wireless remote control.
No part of the product may be modified or adapted.
Take note of all the safety instructions in this user manual.
2. Scope of delivery
•Wireless remote control
•User manual
3. Explanation of icons
An exclamation mark in a triangle in this user manual points to
important instructions that must be observed without fail.
The ‘hand’ symbol indicates special tips and information on
operation.
5
4. Safety instructions
The product’s guarantee becomes invalid, if the product is
damaged as a result of the failure to observe these operating
instructions! We do not assume any liability for any resulting
damages!
We do not assume liability for damage to property or
personal injury caused by improper use or failure to observe
the safety instructions. In such cases the product’s guarantee
becomes invalid.
Dear customer, the following safety instructions are intended to protect
you as well as the device. Please take time to read through the following
points:
a) General information
•For safety and licensing (CE) reasons any unauthorised alterations to and/
or modification of the product are not permitted.
•This product is not a toy and should be kept out of the reach of children.
•The remote control must not get damp or wet, otherwise it may be damaged.
•Do not leave packaging material lying around. This may become a
dangerous plaything in the hands of children.
•All maintenance work, programming or repairs should only be carried out by
a skilled technician or professional workshop.
•Handle the remote control with care; even a fall from a low height can
damage it.
6
b) Handling the batteries
•Keep batteries out of the reach of children.
•Make sure that the polarity is correct when inserting the batteries.
•Do not leave batteries lying around as they could be swallowed by children
or pets. In such case seek immediate medical care.
•Leaking or damaged batteries may cause acid burns, if they come into
contact with skin. Therefore, please make sure you use suitable protective
gloves.
•Make sure that batteries are not short-circuited or thrown into a fire. They
might explode!
•Never take batteries apart!
•Conventional batteries must not be recharged. They might explode!
•If the device is not used for a longer period of time (for example, when
stored), remove the inserted battery to prevent it from leaking and causing
damage.
7
5. General information
The ‘FAZ3000-FB-2’ wireless remote control is part of the ‘FAZ3000’ wireless
alarm system, and is used to activate/deactivate the ‘FAZ-Z’ alarm base
station.
The ‘FAZ3000-FB-2’ wireless remote control can be used to toggle
the ‘FAZ-Z’ alarm base station between three modes, namely
‘disarmed’, ‘internally armed’ and ‘externally armed’.
The remote control also has a built-in panic function. The alarm base station
can trigger an alarm when a specific button combination is entered on the remote
control.
The remote control can be used as an emergency call transmitter
for persons at risk (for instance, cashiers, petrol pump attend-
ants, etc.) in order to trigger an alarm irrespective of the location
in case of an attack.
The remote control has a security code to protect the alarm base station from
unauthorised use; this code must be entered after inserting the batteries before
the initial operation.
The security code comprises a 9-digit button sequence that must be entered
using 3 buttons.
Thanks to the 39= 19683 different codes, an extensive protection against
unauthorised use is guaranteed, since only the remote control registered to
the alarm base station can initiate functions using a specific code. All other
codes are ignored.
Four remote controls with different security codes can be registered in the
alarm base station. However, any number of remote controls can be then
operated using one of these four codes.
Owing to its compact dimensions, the remote control can be also used as a
key chain.
Note that buttons may be pressed accidentally near the alarm
base station if the remote control is kept in one’s pockets. The
alarm base station may be activated or deactivated accidentally
and unintentionally!
8
6. Controls
1‘ext.’ button (= ‘externally armed’)
2‘int.’ button (= ‘internally armed‘)
3LED
4‘unscharf’ button (= ‘disarmed’)
5Opening to attach to a key ring
The cover of the battery compartment is
located at the rear side of the remote
control.
a) Normal button functions
‘unscharf’ (disarm) button (4)
•This button is used to ‘disarm’ the alarm base station.
All sensors except the smoke detectors are deactivated. You can move
around your house freely without setting off the alarm.
An alarm is always triggered when a smoke detector or a glass
break sensor (terminal KL1, NO contact required) connected to
the ‘FAZ-TF’ door/window sensor is triggered.
•A triggered alarm can be stopped by pressing the ‘unscharf’ (disarm) button
(4). The alarm memory is deleted when this button is pressed again.
‘int.’ button (2)
•The ‘internally armed’ mode of the alarm base station is set. This is used
to protect the outer shell, for instance, for protection inside a house at night.
One can move inside the house freely. Ensure that the sensors are
configured accordingly (internal/external sensor).
•The activation is rejected when the button is pressed for the first time if
there is a fault or a magnetic contact is not closed (for instance, a window
is open). The ‘internally armed’ mode is forced to be set when the button
is pressed again.
1
2
3
4
int. ext.
unscharf
5
9
‘ext.’ button (1)
•You can use the ‘ext.’ button to set the ‘externally armed’ mode of the alarm
base station. This function is used to monitor a house when nobody is
present in the house; indoor areas are also monitored (for instance, using
the ‘FAZ-PIR’ PIR motion detector).
•If there is a fault or if a magnetic contact is not closed (for instance, a window
is open), the activation is rejected when the button is pressed for the first
time. The ‘externally armed’ mode is forced to be set when the button is
pressed again.
b) Special function ‘attack alarm’
In the case of an attack, the remote control can be used to immediately set
off an alarm.
This ‘attack alarm’ can be signalled using different components of the
‘FAZ3000’ wireless alarm system, for instance, using an external siren (using
the ‘FAZ-SI’ siren control unit).
Note that in the ‘FAZ-Z’ alarm base station you can customise
the trigger settings in case of an attack (as per the default setting,
the attack alarm can be activated only using the internal siren).
On the remote control two button combinations are each joined by a dashed
line:
•Button combination 1: Button ‘ext.’ and button ‘unscharf’ (disarm)
•Button combination 2: Button ‘int.’ and button ‘unscharf’ (disarm)
Simultaneously pressing one of these button combinations sets off the attack
alarm.
Please note:
An attack alarm is not triggered when all three buttons of the
‘FAZ3000-FB-2’ remote control are pressed simultaneously.
Likewise, simultaneously pressing the two ‘ext.’ and ‘int.’ buttons
does not set off an attack alarm.
You can stop the alarm in the usual way; simply press the ‘unscharf’ (disarm)
button briefly on the alarm base station or the remote control.
10
7. Inserting the batteries,
entering the security code
The security code comprises a 9-digit button sequence that must be entered
(at the time of the initial operation) using the 3 buttons after inserting the
batteries. The security code of the remote control is stored in the alarm base
station so that the remote control can be registered in the ‘FAZ-Z’ alarm base
station later.
If the ‘FAZ-Z’ alarm base station detects the radio signal of the
‘FAZ3000-FB-2’ remote control, the alarm base station responds
only if the received security code matches the stored security
code.
Proceed as follows:
1. Determine a 9-digit security code and note it down on a piece of paper.
The security code may contain only the numbers ‘1’, ‘2’ and ‘4’, for instance,
142142142. The alarm base station can store a maximum of four different
security codes.
You should note down the security code and store it properly. This
is practical when you wish to program another remote control using
the same security code at a later date, or when you wish to ensure
that you do not reuse the same security code accidentally if the
remote control is lost.
2. Open the cover of the battery compartment at the rear side of the remote
control, for instance, using a coin. Rotate the cover clockwise (in the arrow
direction ‘opent’) slightly until it can be removed.
3. Insert one CR2016 type battery observing the correct polarity (the plus pole
‘+’ of the battery has to point outwards towards you).
4. Replace the cover properly and close it by slightly rotating it anticlockwise
(in the arrow direction ‘sclose’).
5. If a security code has been already programmed (if you have simply
replaced the battery), the remote control is ready for operation. Proceed
Table des matières
Autres manuels Conrad Electronic Télécommande
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
