Confer Plastics EVOLUTION 7100 Guide de configuration

MODEL #7100

“EVOLUTION” A-FRAME LADDER

FOR RIGID-FRAMED POOLS ONLY

ASSEMBLY AND INSTALLATION MANUAL

Made in U.S.A. by

SAVE THESE INSTRUCTIONS

DEALER/INSTALLER: GIVE TO HOMEOWNER

The Anti-Entrapment Barrier is included in this ladder for the U.S. and Canada only, as required by ANSI/APSP requirements.

The Anti-Entrapment Barrier is NOT intended as a substitute for competent adult supervision.

If you would like to purchase the barrier, please visit our website at: www.conferladders.com

Platform

Ladder Leg

Tr e a d

Connector

Swing Up

Tread

Upper Brace

Standard

Tread

Extension

Boot

Lower Base

Large

Barrier Small

Barrier

Hardware Pack

4-1/4-20x2"Bolt

4 - 1/4 - 20 Acorn Nut

2 - #10 x 1-1/4" Screw

2-1/4-20x2-1/4"Bolt

2-1/4”FlatWasher

2-1/4-20HexNut

4 - Plug (white)

1 - Padlock

Tools Needed for Assembly

* - Hammer or mallet

* - Phillips Screwdriver

* - Adjustable wrench

* - Liquid soap or lubricant

* - Battery operated drill motor

* - 5/16” Drill bit

Barrier Parts List (if included)

(Included in Hardware Pack)

4 - #10 x 1-1/4” screws

1 - Strip of 4 Foam Pads

1 - Large Barrier Section

1 - Small Barrier Section

1 - Upper Brace

1 - Lower Base

Model #7100 “EVOLUTION” A-FRAME LADDER

Adjustable to fit 48” to 54” Rigid-Framed Above Ground Pools

ASSEMBLY INSTRUCTIONS - PLEASE READ BEFORE ATTEMPTING ASSEMBLY

Parts List

4-LadderLegs

2-TreadConnectors

4-“SwingUp”Treads

6-StandardTreads

4-ExtensionBoots

1 - Platform

If missing parts call - Toll free U.S. - 866-396-2968 or www.conferladders.com

*NOTE: If you are using this ladder on a 48” pool you will not use the extension boots. Proceed to #4.

If the round

plastic inserts,

on the sides of

the extension

boots, are still

in place,

remove them

with a phillips

head screw-

driver as

shown.

Slip the four extension

boots over the ends of

the assembled ladders

legs. They will need to

be all the way on for

most 52” tall pools and

backed off one hole for

54” pools. Depending

upon ground levels out-

side the pool, and sand

levels under the liner

inside the pool, a final

adjustment may need

to be made after the

ladder is put into place.

3. 4. 5.

1. 2.

Using four 1/4-20 x 2” long bolts and

four acorn nuts fasten the extension

boots to the ladder legs Remove the keyhole slot inserts

from two of the ladder legs.

Push the end of one

of the standard treads

into the uppermost

keyhole slot. Make

sure that the tread

and the ladder leg are

positioned as shown

in the photograph

above. It may be nec-

essary to tap the tread

into the slot with a

mallet. Repeat for

three additional

treads.

12. 13.

Tap the platform down until it is fully seated

on the “lugs” of the legs as shown. Using a #10 x 1-1/4” screw fasten the

upper ends of the ladder legs

together as shown. Repeat for

opposite side.

Attach one of the ladder legs to the

opposite ends of the four standard treads

making sure that the curved upper ends

are both facing in the same direction.

Tap the treads downward so that

they seat fully into the bottom of the

keyhole slots.

10.

11.

Tap the ladder leg down onto the ends of

the treads.

Making sure that the

“swing-up” side of the plat-

form is facing away from

the “inside” ladder section,

as shown, slip the open-

ings of the platform over

the upper ends of the lad-

der legs. Using a mallet or

hammer tap the platform

down until it is fully seated

onto the “nubs” of the lad-

der legs. Liquid soap or

lubricant will help the parts

slide together.

Slip the other

two ladder legs

through the

openings of the

platform until

they engage the

other ladder legs

as shown in

next photo.

Insert screws here

17.

Position the tread connector as shown,

with the padlock hole facing upward, and

tap it over the round knob. Repeat for the

opposite tread connector.

Tap the tread connectors onto the ends

of the treads until they are firmly seated.

15. 16.

Position the four “swing up” treads

onto the ladder legs as shown.

14.

Attach the two remaining standard

treads to the extension boots (or directly

to the ends of the ladder legs if installing

on a 48” tall pool).

Snap Small and Large Barrier Sections

into slots on Lower Base as shown.

Separate Barrier sections at the top

slightly and position Upper Brace over

Small Barrier Section. Next, spread the

“fingers” on the Upper Brace and slide

into position on the Large Barrier Section.

Fingers

18. 19.

20.

Place the Base and Brace into position, centered,

on the bottom and fourth treads of the ladder.

Install the four (4) #10 x 1-1/4" screws (included in

hardware pack) on a slight angle, first in the

Upper brace, then in the Lower Base. Install the

self-adhering foam strips to the Large Barrier

Section as shown in diagram.

Foam

Pads

“Swing” up portion of ladder shown

in “down” position and the padlock

in the “holding” area.

Swing up portion of ladder shown in

“up” position, secured with padlock.

21. 22.

Screws

Large

Barrier Small

Barrier

If Ladder

did not

include Barrier, skip steps 18 through 20. Continue to step 21.

OPTIONAL ACCESSORY

SKIM-IT SKIMS OFF DEBRIS Cut cleaning time 75% with skimmer

extension that guides debris directly into your skimmer. Fits most

in-ground and above-ground pool skimmers. Corrosion-resistant

plastic Skim-It installs in seconds without tools.

OPTIONAL CONVERSION KIT

To e a s i l y c o n ve r t y o u r l a d d e r t o a d e c k l a d d e r o r d e r o u r # C K 7 1 0 0 .

The conversion kit includes all parts and hardware needed. Check for

availability at your local pool dealer or order online at

www.conferladders.com

Winterizing: To winterize your ladder pull the ladder

from the pool, remove the plugs, lay the ladder on its

side to allow the water to drain out. A small amount of

water left in the ladder will not cause any damage.

Replace the plugs into the fill holes so that they do not

get lost. The ladder may be left outside.

TO PREVENT FLOATING

Fill the “inner” ladder legs with water and cover the

four fill holes with plugs. Place the ladder over the

pool top seat with the swing up treads on the

outside of the pool. Tip the ladder sideways to

allow the treads to fill the water. This will prevent

floating. The platform should rest on the pool top

seat and the bottom tread should rest firmly on the

pool bottom. If they do not, the extension boots

may be adjusted up or down as required to

achieve the best fit.

For maximum stability, the ladder should be fas-

tened to the top of the pool. Postion the ladder at

the desired location on the pool top seat and mark

the two locations of the holes in the platform onto

the top seat. Move the ladder away, and being

careful not to drill into the liner, drill two holes

through the top seat. Fasten the ladder to the top

seat using two 1/4-20 x 2-1/4” bolts, 1/4” flat wash-

ers, and 1/4-20 hex nuts.

IMPORTANT: WHENEVER THE POOL IS NOT IN USE

THE OUTER TREADS MUST BE IN THE UP POSITION

AND LOCKED WITH THE INCLUDED PADLOCK.

97 Witmer Road

North Tonawanda, New York 14120-2421

Toll Free U.S. 866-396-2968

716-283-1826/ FAX 716-283-3249

www.conferladders.com

Printed in U.S.A.

MADE IN THE U.S.A. by:

6CP-7100B 15M 10/07

CONFER PLASTICS, INC.

LIMITED, PRO-RATED WARRANTY

Confer Plastics, Inc. warrants their swimming pool ladders to be free from defects in workmanship for one year from

date of purchase. After the first year the cost to replace a part is as follows:

MODEL #7100

2nd Year - 20%

3rd Year - 40%

4th Year - 60%

5th Year - 80%

Plus shipping/handling

Enclose proof-of-purchase (receipts, etc.) showing date purchased, your name, address, and daytime phone number. You

will be notified of cost to replace part.

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.

DO NOT RETURN DEFECTIVE PART TO DEALER

The defective part should be returned, postpaid, to:

Confer Plastics, Inc.

97 Witmer Road

North Tonawanda, N.Y. 14120-2421

of current parts

list price

IMPORTANT

FOR YOUR SAFETY

* Check the contents of the carton with the Parts list

for this ladder.

*IfanypartsaremissingcallTollFreeU.S.-

866-396-2968 or visit our web site at

www.conferladders.com

*DO NOT attempt to assemble or install the ladder

if there are ANY shortages of parts or hardware.

*Forproperassemblyandinstallationfollowall

instructions in the sequence shown.

*Beforeusingtheproduct,afterassemblyand

installation, go over the instructions and procedures

again to make sure nothing has been overlooked.

*Besureandsafe.ThemanufacturerIS NOT

responsible for improper assembly, installation

and use.

SAFETY RULES

* Locate ladder on a solid base.

* One person on the ladder at a time.

* Ladder MUST be installed per manufacturer’s

instructions.

* DANGER: No Jumping or Diving from ladder.

* Face ladder when entering and leaving pool.

* To prevent entrapment or drowning — DO NOT

swim through, behind or around ladder.

* Ladder to be used as a swimming pool ladder only.

* Weight limit - 300 lbs maximum

*Warning: Exceeding the maximum weight

restriction may cause the ladder to fail.

* When ladder is not in use lock up outer treads with

padlock provided in hardware bag.

* Consult your local Building Department before

installation of your pool and equipment.

*DANGER:

Use a cordless drill for assembly

and installation. NEVER use an electric drill in

or around the pool.

Table des matières

Autres manuels Confer Plastics Échelle

Confer Plastics

Confer Plastics ROLLGUARD 7200 Guide de configuration

Confer Plastics

Confer Plastics 635-52X Guide de configuration

Confer Plastics

Confer Plastics STEP-ENC Manuel utilisateur

Confer Plastics

Confer Plastics 6000X Guide de configuration

Confer Plastics

Confer Plastics ROLLGUARD 7200 Guide de configuration

Confer Plastics

Confer Plastics 6000 Guide de configuration

Confer Plastics

Confer Plastics 8000 Guide de configuration

Confer Plastics

Confer Plastics 635-52 Guide de l'utilisateur

Confer Plastics

Confer Plastics 6000B Guide de l'utilisateur

Confer Plastics

Confer Plastics CCX-IG Guide de configuration

Confer Plastics

Confer Plastics CK7100-X Manuel utilisateur

Confer Plastics

Confer Plastics PES-1X Manuel utilisateur

Confer Plastics

Confer Plastics PES-G Guide de configuration

Confer Plastics

Confer Plastics 7100X Manuel utilisateur

Confer Plastics

Confer Plastics 6000 Manuel utilisateur

Confer Plastics

Confer Plastics 7100X Guide de configuration

Confer Plastics

Confer Plastics 8100X Manuel utilisateur

Confer Plastics

Confer Plastics 7000X Manuel utilisateur

Confer Plastics

Confer Plastics 8000X Manuel utilisateur

Confer Plastics

Confer Plastics 7000 Manuel utilisateur

Confer Plastics

Confer Plastics 8100X Manuel utilisateur

Manuels Échelle populaires d'autres marques

ADVANCED SIMRACING

ADVANCED SIMRACING ASR6 Manuel utilisateur

Batavia

Batavia GIRAFFE AIR Manuel utilisateur

Millennium

Millennium L-220-SL Manuel utilisateur

Louisville

Louisville AA2210 Manuel utilisateur

wibe

wibe TMR Guide de l'utilisateur

BESSLER

BESSLER 20 Manuel utilisateur

Branach

Branach TerrainMaster Manuel utilisateur

TUBESCA-COMABI

TUBESCA-COMABI 02271 105 à 115 Manuel utilisateur

KTL

KTL 24392909 Manuel

Penguin

Penguin ICE LADDER Manuel utilisateur

KRAUSE

KRAUSE 1103 Series Manuel utilisateur

Tractel

Tractel skysafe Instructions d'utilisation

AFIX

AFIX FAST FIX Manuel utilisateur

Wenger

Wenger Fixed Height Stairway 2-Step Manuel utilisateur

KRAUSE

KRAUSE 1212 Manuel utilisateur

fakro

fakro LWS-P 22/47 Manuel utilisateur

FACAL

FACAL Euro Stilo Manuel

SHEDorize

SHEDorize Stepladder/Rake/Cord Rack Manuel utilisateur