Condec Orion-2C Manuel utilisateur

68859

Orion-2C, Orion-2D, Orion-3A

& MPV-10K

Pneumatic Pressure Controllers

Adjustment & Maintenance

Manual

*Patent No. 4,698,998

Condec Web Site: www.4condec.com

Condec Sales Phone Number: (888) 295-8475

Speciﬁcations subject to change without notice.

August 2001

Contents

About This Manual ...................................................................................................................................1

1.0 Introduction................................................................................................................................. 1

2.0 Maintenance................................................................................................................................ 2

2.1 O-ring Repair Kit Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.2 Recommended O-ring materials. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.3 ORION Manifold - Valve Seat Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.4 ORION Manifold - Vernier Control Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.5 ORION Manifold - Vernier Control Reassembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.6 ORION Manifold - Valve Seat Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.7 MPV-10K Manifold - Valve Seat Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.8 MPV-10K Manifold - Valve Seat Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.9 ORION Manifold - Valve Adjustment Procedure (Customer Installation). . . . . . . . . . . . . . . . . . . . . . 7

2.10 MPV-10K Manifold - Valve Adjustment Procedure (Customer Installation). . . . . . . . . . . . . . . . . . . . 8

2.11 Recommended Mounting Patterns. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.12 ORION-2C Valve Assembly (55283) Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.13 ORION-2D Valve Assembly (55286) Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.14 ORION-3A Valve Assembly (55287) Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.15 MPV-10K Valve Assembly Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.0 Specifications........................................................................................................................... 22

3.0.1 ORION-2C (PN 55283) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.0.2 ORION-2D (PN 55286) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.0.3 ORION-3A (PN 55287) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.0.4 MPV-10K . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Orion/MPV-10K Warranty and Return Policy...................................................................................... 23

Orion/MPV-10K Return Material Authorization Form......................................................................... 24

Introduction

About This Manual

The ORION/MPV-10K is a pneumatic pressure

controller with precision vernier. A rugged, compact

controller manufactured by Condec, designed to

provide ease of operation and installation, by a

qualiﬁed technician.

Equipped to perform and be maintained on-site, these

controllers have proven to substantially reduce the

cost, system down-time and man-hours of labor

normally associated with these routine service

functions.

The patented controller was designed as an all

mechanical device that has been factory adjusted and

ready for on-site installation.

This manual has been written to give the user a simple

and clear explanation of how to operate, and

troubleshoot these controllers.

Before attempting to use either style,

Pressure Controller, the following

instructions must be carefully read

and understood by personnel utilizing

the equipment. This is a high-pressure

system. It is strongly recommended

that only personnel formally trained in

the use of pneumatic pressure

equipment be permitted to operate it.

Potentially dangerous conditions

could be produced through negligent

handling or operation of the valve due

to the high pressure used within the

unit.

These units are strictly for use with pneumatic pressures.

Erroneous readings and potential damage could result

from the introduction of hydraulic ﬂuids into the internal

valve body.

Authorized distributors and their

employees can view or download this

manual from the Condec distributor

site at

www.4condec.com

1.0 Introduction

The ORION/MPV-10K represents the latest in technology, offering a combination of features, performance,

versatility and reliability not previously available in a pneumatic pressure controller. Some of the more

outstanding features are listed below:

•Simple Operation: Accompanying operator's manual provides clear, concise instructions for system

operation.

•ORION-2C, ORION-2D, ORION-3A: To obtain a speciﬁc pressure, either the Inlet Pressure valve or the

Vent (outlet) valve (two outer valves) may be used since both provide precise control. As the pressure

approaches the desired value, the valve being used for control should be slowly rotated clockwise to its

closed position. With a little experience, pressure values very close to the desired ﬁnal value may be

quickly achieved. To obtain exact ﬁnal pressure, slowly rotate the Vernier Control (middle) Knob in the

desired direction, clockwise to increase pressure.

•MPV-10K: The pressure valve will begin to open when it is turned counter clockwise approximately 15

degrees. Full open position of the valves is achieved with a maximum of 3 1/2 turns from the closed

position. The valve has a ﬁne adjustment sensitivity. Very low torque is required to turn the vernier, so use

ﬁngertip adjustment.

•Safe, Clean Operation: All pressure components are made of brass, aluminum or stainless steel and

proof-tested to at least 150% of maximum operating pressure.

The heart of the ORION controllers are the two micro-metering valves and the vernier provided for control of

pressure. Overpressure protection must be customer provided, if required, by a fully adjustable pressure regulator

which is manually set to limit the system input pressure. The ORION/MPV-10K is designed for compatibility

with Nitrogen and shop air. Other O-ring materials are available through special ordering or repair kits.

Warning

Orion/MPV-10K Adjustment & Maintenance Manual

2.0 Maintenance

This section outlines the mechanical repair procedures for the ORION/MPV-10K pressure source. The repair

procedures cover the major components and subassemblies which are critical to the proper functioning of the

calibrators and that will likely need periodic maintenance over the life of the unit. Only those persons who are

formally trained as skilled technicians should attempt to repair these units. All relevant safety precautions should

be observed due to the presence of high-pressure cylinders.

2.1 O-ring Repair Kit Data

O-ring repair kits: Nitrile Buna - N (PN 58499)

Ethylene - Propylene (PN 58506)

Silicone (PN 58509)

Neoprene (PN 58515)

Fluorocarbon "Viton" (PN 55277)

May be used with: ORION-2C Pneumatic Pressure Controller (PN 55283)

ORION-2D Pneumatic Pressure Controller (PN 55286)

ORION-3A Pneumatic Pressure Controller (PN 55287)

MPV-10K Valve Assemblies - (all Part Numbers)

NOTE:

A small coating of Fluorinated Krytox grease (PN 55593) should be applied to both sides of O-ring prior to

installation.

2.2 Recommended O-ring materials

NOTE:

Ratings are recommended for use in the Condec products and are meant to be used only as a guide. Based on

your application you may need to do testing. The O-ring material applications listed below are for reference only and are

not to be used in the valves.

Nitrile Buna - N (BN)

The standard for most general applications (petroleum-based lubricants, hydraulic oils, gasoline, fuels, alcohol,

LP gases, water, and many other media).

Temperature range: -65 to +300 F

Pressure rating: 0-6000 PSI

Neoprene (C)

For reﬁgeration (freon gases, carbon dioxide gases, chlorine, ozone, sunlight exposure. FDA approved for food

and beverage, odorless, tasteless, non toxic).

Temperature range: -80 to +260 F

Pressure rating: 0-6000 PSI

Ethylene-Propylene (EP)

For hot water, steam, acids, alcohols, alkalis, keytones, phosphate, and brake ﬂuids.

Temperature range: -67 to +302 F

Pressure rating: 0-6000 PSI

Fluorcabon "Viton" (V)

High temperature compatible with wide range of ﬂuids and chemicals. Acids, oils, fuels, solvents and gases.

Temperature range: -65 to +500 F

Pressure rating: 0-10000 PSI

Maintenance

Silicone (S)

For high temperature applications. Compatible with air, oxygen, ozone and others.

Temperature range: -85 to +482 F

Pressure rating: 0-3000 PSI

Figure 2-1. Additional ORION-2C O-ring Replacement Parts

2.3 ORION Manifold - Valve Seat Removal

(ORION-2C: Refer to the List of Parts - Table 2-1 on page 10, and Exploded View - Figure 2-6 on page 12)

(ORION-2D: Refer to the List of Parts - Table 2-2 on page 13, and Exploded View - Figure 2-8 on page 15)

(ORION-3A: Refer to the List of Parts - Table 2-3 on page 16, and Exploded View - Figure 2-10 on page 18)

Tools required: A/R solvent (de-natured alcohol)

socket wrench

3/4" socket

needle housing socket (PN 65580)

isolation valve needle housing socket (PN 68509)

hex wrench (.050")

hex wrench (.061")

needle-nose pliers

tube ﬂuorinated krytox grease (PN 55593)

hand drill

No. 43 drill

No. 4-40 tap

tap handle

small hammer

Procedure:

1. Secure the manifold by its center portion, in a bench vise, with the valve knobs pointing upward.

2. Using the .061" hex wrench, loosen and remove the knob inserts (4), as well as, the nylon washer (33)

from the pressure and vent valve stems.

3. Using the .050" hex wrench, loosen and remove the setscrew (34) and lock nut (2).

4. Loosen the 3/4" lock nuts (1) on the

COARSE

(inlet pressure) and

VENT

valve threaded needle housings

(10).

5. Using the needle housing socket (65580) and socket wrench, loosen and remove the needle/housing

assembly (10,11).

6. To disassemble the

ISOLATION

valve(s), ﬁrst remove the valve needle (18) by turning the gear (6)

clockwise.

7. Loosen and remove the valve housing(s) (19) using the isolation valve housing removal socket (68509),

and socket wrench.

8. Remove the valve stem seat(s) (8) and valve needle seat(s) (9) by using the needle-nose pliers.

9. Remove the inner and outer O-ring(s) (28, 27) and back-up ring(s) (31, 30) from the valve stem seats and

wash all parts in solvent.

10. To remove valve seats (7) from either the

COARSE

(inlet pressure),

VENT

ISOLATION

valve(s), try

blowing compressed air through the inlet and outlet ﬁttings. Otherwise, the center holes have to be

drilled and a tap used to extract the seat (steps 11-14).

Orion/MPV-10K Adjustment & Maintenance Manual

11. Using the hand drill, with the No. 43 bit, carefully drill out the seat hole, ensuring that the drill does not

touch the hole in the manifold housing directly beneath the seat (7).

12. Blow out any chips from the seat area using compressed air.

13. While holding the 4-40 tap perpendicular to the seat, slowly turn until the tap starts to engage the seat.

14. When the tap has engaged into the seat, use a small hammer and gently knock upward against the tap

handle to extract the seat.

15. After the seat has been removed, blow any remaining chips from the seat area.

2.4 ORION Manifold - Vernier Control Disassembly

Tools required: A/R solvent (de-natured alcohol)

open end wrench (1-1/4")

ﬂat blade screwdriver

socket wrench

isolation valve needle housing socket (PN 68508)

isolation valve needle housing socket (PN 68509)

1. With the manifold housing mounted in a vise, turn the

VERNIER

shaft (14) clockwise until the piston is

bottomed.

2. Loosen and remove the end cap (13) using a 1-1/4" wrench. At certain points during removal the end cap

will appear to lock up. If this occurs, rotate the shaft clockwise until the end cap is free to turn.

3. Remove the O-ring (29) from the end cap.

ORION-3A: Also remove the backup washer (38) from the end cap.

4. Remove the self-sealing screw (36) that acts as the piston key.

5. Remove the piston (15) by partially screwing in the threaded end of the

VERNIER

shaft (14) and pulling.

6. Remove the O-ring (32) from the piston groove.

7. To disassemble the end cap/shaft assembly, mount the end cap in the vise.

8. Loosen and remove the locknut (20) using the isolation valve housing socket (PN 68509) and socket

wrench.

9. ORION-2C, ORION-2D: Loosen and remove the end bushing (12) using the same socket. Remove the

shaft (14). Remove the mylar bearing washer (41 or 42) from both sides of the shaft ﬂange.

ORION-3A: Loosen and remove the end bushing (12) using the isolation valve housing socket (PN

68508) and socket wrench. Remove the shaft (14). Remove the ball bearings (41) from both sides of the

shaft ﬂange.

10. Use a small pick or screwdriver to remove the O-ring (27) from the inner groove of the end cap (13).

ORION-3A: Also remove backup retainer (39) from inner groove of the end cap (13).

11. Wash all parts in solvent and blow dry with compressed air.

2.5 ORION Manifold - Vernier Control Reassembly

(ORION-2C: Refer to the List of Parts - Table 2-1 on page 10, and Exploded View - Figure 2-6 on page 12)

(ORION-2D: Refer to the List of Parts - Table 2-2 on page 13, and Exploded View - Figure 2-8 on page 15)

(ORION-3A: Refer to the List of Parts - Table 2-3 on page 16, and Exploded View - Figure 2-10 on page 18)

Tools required: tube ﬂuorinated krytox grease (PN 55593)

open end wrench (1-1/4")

ﬂat blade screwdriver

socket wrench

isolation valve needle housing socket (PN 68508)

isolation valve needle housing socket (PN 68509)

torque wrench

1. Coat all O-rings and backup washer/retainers with Krytox grease before installing. Make sure that the

O-rings and backup rings/washers are installed in the proper order.

2. Install the small O-ring (27) into the end cap inner groove.

ORION-3A: Also install backup retainer (39) in inner groove of the end cap (13).

Maintenance

3. ORION-2C, ORION-2D: Add mylar washers (41 or 42) to each side of shaft (14). Apply a small amount

of Krytox grease to the shaft threads and install the shaft (14) into the end cap (13).

NOTE:

Part number and quantity will vary. Washers are used to adjust vertical play in shaft (14). Try one washer (41) on

each side to start.

Install the end bushing (12) and tighten until snug using the isolation valve needle housing socket (PN

68509) and socket wrench.

ORION-3A: Hold shaft (14) vertically with end that goes through end bushing (12) toward ceiling. Place

light coating of grease on threads of shaft. Place thick coating of grease on top of shaft bearing surface.

Allowing grease to hold ball bearings in place. Slide end bushing (12) over top of shaft and down to

contact top of ball bearings. Rotate shaft assembly 180°, placing end bushing towards the ﬂoor. Be

careful not to displace ball bearings. Place thick coating of grease on shaft and bearing surface. Place

sixteen chrome ball bearings (41) on greased surface, allowing grease to hold them in place. Install

shaft with bearings into end cap. Install the end bushing and tighten until snug using the isolation valve

needle housing socket (PN 68508) and socket wrench.

4. ORION-2C, ORION-2D: Feel vertical motion of shaft (14). If motion exists, add thicker washer (42) at

step 3, otherwise continue to step 5.

ORION-3A: Tighten so that shaft rotates, but should be ﬁrm. Verify no up and down movement. If there

is up and down movement, retighten end bushing.

5. Install the locknut (20) into end cap (13) and using the isolation valve needle housing socket (PN 68509)

and torque wrench. Torque to approximately 325 in. lbs. (may not get to torque on all sub-assemblies).

6. Install the O-ring (32) in the piston groove and install the piston (15) into the

VERNIER

cavity. Ensure

that the piston key way is facing the hole into which the self-sealing screw (36) is assembled.

7. Install the self-sealing screw (36) and tighten until snug.

8. Install the O-ring (29) on the end cap/shaft assembly, install into manifold and tighten until snug.

ORION-3A: Also install backup washer (38) on the end cap/shaft assembly.

2.6 ORION Manifold - Valve Seat Replacement

(ORION-2C: Refer to the List of Parts - Table 2-1 on page 10, and Exploded View - Figure 2-6 on page 12)

(ORION-2D: Refer to the List of Parts - Table 2-2 on page 13, and Exploded View - Figure 2-8 on page 15)

(ORION-3A: Refer to the List of Parts - Table 2-3 on page 16, and Exploded View - Figure 2-10 on page 18)

Tools required: A/R solvent (de-natured alcohol)

socket wrench

3/4" socket

female socket (PN 65581)

needle housing socket (PN 65580)

isolation valve needle housing socket (PN 68509)

hex wrench (.061")

hex wrench (.050")

torque wrench

needle-nose pliers

tube Fluorinated Krytox grease (PN 55593)

No. 43 drill

1. Install a new seat (7) by placing it into the seat well with the needle-nose pliers. Ensure that the seat is

centered within the cavity and gently tap it with a blunt end of a drill bit to install.

2. Install the valve needle seat (9) with the smaller diameter end facing outward.

3. Install new O-rings (28, 27) inside and outside of the valve stem seat (8). Coat all O-rings and back-up

rings (30, 31) with ﬂuorinated Krytox grease before installation. Make sure that the rings are installed in

the proper order.

4. Install the valve stem seat (8) by grasping the small diameter end with the needle-nose pliers and

positioning in the valve cavity, then properly seat by gently pushing with the blunt end of a drill bit.

5. For the two outer valves, disassemble the valve needle (11) from its housing (10) and check for any burrs

or dirt on the threads which might interfere with smooth operation.

Orion/MPV-10K Adjustment & Maintenance Manual

6. Clean both the needle (11) and housing (10) in solvent, dry the parts and apply a small amount of

ﬂuorinated Krytox grease to the needle threads before reassembly.

7. Assemble the needle into the valve housing and turn it until it stops.

8. Reinstall the needle/housing assembly into the valve cavity until ﬁnger tight.

9. Mount the manifold body (16) in a vise. For the pressure and vent valves (outer) only, torque the

needle/housing assembly to 325 in. lbs. using the needle housing socket (PN 65580) and torque wrench.

10. Install the housing lock nuts (1) onto the housing (10) and tighten until snug with the 3/4" socket.

11. Using the .050" hex wrench, install and tighten the lock nut (2) and set screw (34).

12. Install the knob insert (4) and nylon washer (33) over the needle shaft (11), align the set screws (23) with

the indents and tighten with the .061" hex wrench.

13. For the

ISOLATION

VACUUM

(inner) valves, install the needle housing (19) and tighten until snug

using the housing installation socket (PN 68509) and torque wrench (there is no speciﬁed torque, so use

care when tightening so as not to break the socket nibs).

14. Install the gear (6) over the isolation or vacuum (inner) valve needle (18) shaft, align the set screws (26)

with the indents and tighten with the .061" hex wrench.

15. Apply a small amount of ﬂuorinated Krytox grease to the threads of the isolation or vacuum (inner) valve

needle(s) (18) and install into the valve by turning counter-clockwise. Rotate the gear counter-clockwise

until the needle just stops at the seat.

2.7 MPV-10K Manifold - Valve Seat Removal

(MPV-10K - refer to the list of parts - Table 2-4 on page 19, and Figure 2-12 on page 21)

Tools required: A/R solvent (de-natured alcohol)

socket wrench

3/4" socket

needle housing socket (PN 65580)

isolation valve needle housing socket (PN 68509)

hex wrench (.050")

hex wrench (.061")

needle-nose pliers

tube ﬂuorinated krytox grease (PN 55593)

hand drill

No. 43 drill

No. 4-40 tap

tap handle

small hammer

1. Secure the manifold in a bench vise by its center portion with the valve knob pointing upward.

2. Using the .061" hex wrench, loosen and remove the knob (15) and the nylon washer (14) from the

pressure valve stem (3) or (6).

3. Using the .050" hex wrench, loosen and remove the set screw (13) and lock nut (12).

4. Loosen the 3/4" lock nut (11) on the pressure valve threaded needle housing (2).

5. Using the needle housing socket (PN 65580) and socket wrench, loosen and remove the needle/housing

assembly (2,3) or (2,6).

6. Remove the valve stem seat (10) and valve needle seat (5) by using the needle-nose pliers.

7. Remove the inner and outer O-rings and back-up rings (7,9) from the valve stem seats and wash all parts

in solvent.

8. To remove valve seat (4), blow compressed air through the inlet and outlet ﬁttings. If this is unsuccesful,

the center holes will have to be drilled and a tap used to extract the seat (steps 9 - 12).

9. Using the hand drill with No. 43 bit, carefully drill out the seat hole, ensuring that the drill does not touch

the hole in the manifold housing directly beneath the seat (4).

10. Blow out any chips from the seat area using compressed air.

11. While holding the 4-40 tap perpendicular to the seat, steadily and slowly turn until the tap starts to

engage the seat.

Maintenance

12. When the tap has engaged into the seat, use a small hammer and gently knock upward against the tap

handle to extract the seat.

13. After the seat has been removed, blow any remaining chips from the seat area.

2.8 MPV-10K Manifold - Valve Seat Replacement

(MPV-10K - refer to the list of parts - Table 2-4 on page 19, and Figure 2-12 on page 21)

Tools required: A/R solvent (de-natured alcohol)

socket wrench

3/4" socket

needle housing socket (PN 65580)

hex wrench (.061")

torque wrench

needle-nose pliers

tube Fluorinated Krytox grease (PN 55593)

No. 43 drill

1. Install a new seat (4) by placing it into the seat with the needle-nose pliers. Ensure that the seat is

centered within the cavity and gently tap it with a blunt end of a drill bit to install.

2. Install the valve needle seat (5) with the smaller diameter end facing outward.

3. Install new O-rings inside and outside of the valve stem seat (5). Coat all O-rings and back-up rings

(7,9) with Krytox grease before installation. Make sure that the O-rings and back-up rings are installed in

the proper order.

4. Install the valve stem seat (10) by grasping the small diameter end with the needle-nose pliers and

positioning in the valve cavity, then gently pushing with the blunt end of a drill bit.

5. Disassemble the valve needle (3 or 6) and valve needle housing (2) and check for any burrs or dirt on the

threads which might interfere with smooth operation.

6. Clean both the valve needle (3 or 6) and valve needle housing (2) in solvent, dry the parts and apply a

small amount of Krytox grease to the valve needle threads before re-assembly.

7. Assemble the valve needle (3 or 6) into the valve needle housing (2) and turn until it stops.

8. Reinstall the needle/housing assembly into the valve cavity until ﬁnger tight.

9. Mount the manifold body (1) in a vise. Torque the needle/housing assembly to 325 in. lbs. using the

needle/housing socket (PN 65580).

10. Install the housing locknut (11) onto the valve needle housings (2) and tighten until snug with the 3/4"

socket.

11. Using the .050" hex wrench, install and tighten the lock nut (12) and set screw (13).

12. Install the nylon washer (14) and knob (15) over the valve needle (3 or 6) shaft, align the set screws (16)

with the indents and tighten with the .061" hex wrench.

2.9 ORION Manifold - Valve Adjustment Procedure (Customer Installation)

(ORION-2C Refer to the List of Parts - Table 2-1 on page 10, and Exploded View - Figure 2-6 on page 12)

(ORION-2D Refer to the List of Parts - Table 2-2 on page 13, and Exploded View - Figure 2-8 on page 15)

(ORION-3A Refer to the List of Parts - Table 2-3 on page 16, and Exploded View - Figure 2-10 on page 18)

NOTE:

The following minimum customer supplied input pressure equipment is required. Input supply pressure with a

supply gauge and pressure regulator.

Tools required: hex wrench (.050")

hex wrench (.061")

1. Turn the supply pessure regulator off and vent manifold.

2. If not already done, remove the ORION input and vent valve (outer) knobs (3) using the .061" hex

wrench.

3. Using a .050" hex wrench, loosen the set screw (34) on each ORION input and vent valve locknut (2)

and turn each locknut clockwise to its stop.

Orion/MPV-10K Adjustment & Maintenance Manual

4. Check to see that each knob insert (4) is securely fastened to the ORION input and vent valve shaft (11).

If it is loose, re-tighten the set screws (23) with the .061" hex wrench.

5. Close the input valve by turning the knob insert (4) clockwise until you feel the valve needle seat on the

O-ring (valve is now in closed position).

6. Rotate gear(s) (small gears with 18 teeth) on isolation valve(s), counter clockwise (gear[s] will rotate

towards valve body) until they stop. Then rotate each gear clockwise 1/2 turn to open isolation valves.

7. Turn the supply pressure regulator to increase the supply pressure to between 80% and 100% of

customers line pressure (ORION-2C or ORION-3A: maximum 3000 PSI; ORION-2D: maximum 300

PSI).

8. Open the

VENT

valve to atmosphere to release line pressure, then close the

VENT

valve.

9. Slowly open the input valve by turning the knob insert (4) counter-clockwise until you notice the input

pressure gauge pressure increase. Then turn the knob insert (4) slightly clockwise until the pressure stops

rising.

10. Mark a radial line at the 12 o’clock position on the knob insert.

11. Turn the knob insert (4) clockwise to move the mark to the 6 o’clock position.

12. Turn the locknut (2) counter-clockwise until it contacts the bottom of the stop washer. Tighten the set

screw (34) on the locknut with the .050" hex wrench.

13. Install the input valve knob (3) on the knob insert (4) and engage its gear (5) with the smaller isolation

valve gear (6). Turn the knob clockwise until the isolation valve is slightly snug.

CAUTION:

do not use excessive torqure when doing this. The seat may be damaged

14. Remove the input valve knob (3). Align the set screws (25) with the indentations on the knob insert.

Install the knob on the knob insert (4) while engaging the knob gear (5) with the isolation valve gear (6).

15. Tighten the set screws (25) with the .061" hex wrench. The input valve is now adjusted.

16. To adjust the

VENT

valve (ouput). Close the input valve by turning the output valve knob clockwise.

17. Close the

VENT

valve knob insert (4) clockwise until slightly snug.

18. With the supply pressure at customer’s 100% line pressure (ORION-2C or ORION-3A: maximum 3000

PSI; ORION-2D: maximum 300 PSI). Open the

COARSE

valve until the indicated pressure stabilizes

and then close the

COARSE

valve.

19. Slowly turn the

VENT

valve (ouput) knob insert (4) counter-clockwise until you hear ﬂow from the

VENT

valve, then turn the knob insert (4) slightly clockwise until the pressure stops decreasing.

20. Repeat steps 10 - 15 for the

VENT

valve, replacing the term "input valve" with "output valve."

2.10 MPV-10K Manifold - Valve Adjustment Procedure (Customer Installation)

(MPV-10K - Refer to the List of Parts - Table 2-4 on page 19, and Figure 2-12 on page 21)

NOTE:

Customer must supply, as a minimum, input supply pressure with a supply guage and pressure regulator.

Tools required: hex wrench (.050")

hex wrench (.061")

1. Turn the supply pressure regulator off.

2. If not already done, remove the MPV-10K knob (15) using the .061" hex wrench.

3. Using a .050" hex wrench, loosen the set screw (13) on the MPV-10K valve locknut (12) and turn

locknut clockwise until it stops.

4. Align the set screws (16) with the indentations on the valve needle (3 or 6). Install the knob using the

.061" hex wrench.

5. Turn the supply pressure regulator, to increase the supply pressure to between 80% and 100% of

customer’s line pressure (maximum 10,000 PSI). Let system settle for 5 minutes.

NOTE:Some valves may not be recommended for 10000 PSI, because of O-ring material selection. See Section 2.2 on

page 2.

6. Slowly open the MPV-10K valve by turning the knob (15) counter-clockwise until you notice the

pressure of the input pressure guage increase. Then turn the knob slightly clockwise until the pressure

stops rising.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Condec Contrôleurs

Condec

Condec UVC1000 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur