Comtech EF Data OAC-170D Manuel utilisateur

OAC-170D 70 MHZ AMPLIFIER ADJUSTMENT

The OAC-170D Amplifier Adjustment is performed to ensure that the total gain from the

Downconverters to the input of the CS6716 is set for 40db +/- .25db. The OAC-170D

provides the necessary gain between the downconverter outputs and the CS6716 digital

troposcatter modem inputs via four 16db adjustable IF amplifiers.

NOTE: This procedure is not normally required in the field; however, it should be

performed after the replacement of any major equipment in the receive chain. LNA,

downconverter, IF Test Panel and/or any associated cables in the receive path.

STEP 1

Set the CS6716 modem to Default Configuration and place Modem to Online state:

a. On the modem front panel keypad, select ENT for Main Menu then select

ON/OFFLINE, then select OFFLINE to place the modem in the offline state.

b. From the Main Menu select CONFIG, then select DEFAULT to set the modem to

default configuration.

c. From the Main Menu select ON/OFFLINE, and then select ONLINE to place the

modem into the online state.

STEP 2

Remove all of the U links from the IF Data Patch Panel as shown in Fig 1.1.

Figure 1.1

STEP 3

Set the Filter select switch on the OAC-170D to BYPASS.

STEP 4

Connect the TX1 IF output to the RX1 IF input on the IF Data Patch panel using the

supplied 16db inline attenuator as shown in Fig 1.2.

Figure 1.2

STEP 5

On the modem front panel keypad, Select ENT for Menu, select MONITOR, then select

RSL to display the Receive Signal Level (RSL) for all four receive channels.

STEP 6

On the OAC-170D front panel, adjust RCVR-1 potentiometer until a reading of -40 dBm

is obtained on the CS6716 modem RSL1 display, refer to Fig 1.3

NOTE: Clockwise (CW) Increases the level.

Figure 1.3

STEP 7

Repeat steps 4-6 for each corresponding RX IF inputs 2, 3 and 4. Refer to Fig 1.4 and

Fig 1.5.

TX1IFtoRX2IF

TX1IFtoRX3

TX1IFtoRX4IF

Figure 1.4

Figure 1.5

STEP 8

Restore equipment to original configuration.

GAIN EQUALIZATION

This procedure is performed to equalize the total gain through the receive path to the CS-

6716 modem. Gain Equalization is necessary for the modem to take advantage of the

multiple diversity schemes in the various AN/TRC-170 systems

STEP 1

For proper Gain Equalization, the system must not be in loop-back and the RX system

must be tuned at least 100 MHz away from the XMT frequency. If the antenna and

waveguide have not been installed, place the waveguide terminators or cover plates on

the receive ports of the waveguide entry panel. If the antenna and waveguide have been

installed, adjust the receiver amplifier converter and frequency synthesizer receive

frequency at least 200 MHz away from the normal receive frequency and at least 100

MHz from the transmit frequency. Make sure the HPA is off.

STEP 2

Set the CS6716 modem to Default Configuration and place Modem to Online state:

d. On the modem front panel keypad, select ENT for Main Menu then select

ON/OFFLINE, then select OFFLINE to place the modem in the offline state.

e. From the Main Menu select CONFIG, then select DEFAULT to set the modem to

default configuration.

f. From the Main Menu select ON/OFFLINE, and then select ONLINE to place the

modem into the online state.

STEP 3

On the modem front panel keypad, Select ENT for Menu, select MONITOR, then select

RSL to display the Receive Signal Level (RSL) for all four receive channels.

STEP 4

On each Downconverter, turn the Noise Test Switch to PRESEL as shown in fig 1.1.

Figure 1.1

STEP 5

While observing the RSL levels on the CS6716 Modem front Panel display, adjust

RCVR1-RCVR4 potentiometers on the OAC-170D for the lowest common RSL to

within +/- 0.25 dB. Refer to fig 1.2 and fig 1.3.

NOTE: The lowest RSL is the highest numerical value i.e. -74 is lower than -72.

Therefore RCVR-2 and RCVR-3 need to be adjusted from -72 down to -74 in fig 1.2.

When adjusting the potentiometers; Clockwise (CW) increases the level and Counter

Clockwise (CCW) decreases the Level.

Figure 1.2

Properly gain equalized system

Figure 1.3

STEP 6

On each Down Converter, turn the Noise Test Switch to OFF and tune the receiver

amplifier-converter and frequency synthesizer receive frequency back to the normal

receive frequency.

Table des matières

Autres manuels Comtech EF Data Amplificateur

Comtech EF Data

Comtech EF Data TRP1000-OD Manuel utilisateur

Comtech EF Data

Comtech EF Data XPA-200 Manuel utilisateur

Comtech EF Data

Comtech EF Data XTD-750C-B1 Fiche technique

Comtech EF Data

Comtech EF Data HPOD Manuel utilisateur

Comtech EF Data

Comtech EF Data LPOD PS 1 Manuel utilisateur

Comtech EF Data

Comtech EF Data CLNA Manuel utilisateur

Comtech EF Data

Comtech EF Data LPOD PS 1.5 Manuel utilisateur

Comtech EF Data

Comtech EF Data KPA-040 Manuel du propriétaire

Comtech EF Data

Comtech EF Data LNA Series Manuel utilisateur

Comtech EF Data

Comtech EF Data LPOD Manuel du propriétaire

Comtech EF Data

Comtech EF Data LPOD-R PS .5 Manuel du propriétaire

Comtech EF Data

Comtech EF Data CPA-050 Manuel utilisateur

Comtech EF Data

Comtech EF Data KPA-020IN Manuel utilisateur

Comtech EF Data

Comtech EF Data KPA-080 Manuel utilisateur

Comtech EF Data

Comtech EF Data C Manuel utilisateur

Comtech EF Data

Comtech EF Data LGAN Manuel utilisateur

Comtech EF Data

Comtech EF Data HPOD Manuel utilisateur

Comtech EF Data

Comtech EF Data PCB-4000A Manuel utilisateur

Comtech EF Data

Comtech EF Data LNAS Manuel utilisateur

Comtech EF Data

Comtech EF Data LPOD Manuel utilisateur

Comtech EF Data

Comtech EF Data LPOD Series Manuel utilisateur

Comtech EF Data

Comtech EF Data XTD-400C Fiche technique

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur