CompuLab IPC2 Manuel utilisateur

IPC2

Owner’s Manual

IPC2 Owner’s Manual

February -2014

Introduction

Package contents

Hardware specifications

IPC2 features

Quick start guide

Connecting IPC2

Booting Linux

Booting Windows 7

Maintenance

Opening service door

Service bay

BIOS Setup Utility

Warranty and RMA

Warranty

RMA

Tips for saving power

General

In Operating System

For more information and to obtain the latest revision of this document, please visit

www.fit-pc.com

Introduction

Package contents

1. IPC2 computer

2. Power supply: input 100-240VAC 50/60Hz, 60W output 12VDC 5A, DC plug lock,

3. Attachable Standard North-American and EU plugs AC cord. *

4. HDMI to DVI adapter

5. Audio 3.5mm to RCA cable

6. 2 WiFi antennas (in some models)

7. Mini-serial to DB9-female adapter cable

To use IPC2, you will need:

A display with DVI, HDMI or DisplayPort input + DVI, HDMI or DisplayPort cable

USB keyboard and mouse

* Local resellers may supply IPC2 with other AC cord types.

Hardware specifications

Processor

Type

Intel 4th Gen Core Celeron-2955U / i3-4010U / i5-4300U / i7-4600U

(Haswell)

Cores

64-bit dual core

Clock speed

1.4-2.1GHz (turbo boost up to 3.3GHz) (depends on CPU)

TDP

15W

Chipset

Mobile Intel 8 Series (Lynx Point) in MCP package

Memory

Supported

2x SO-DIMM 204-pin DDR3L SDRAM memory slots

Up to 16GB (2x 8GB) DDR3L-1600 (1.35V only)

Storage

Supported

1x SATA up to 6 Gbps (SATA 3.0) for internal 2.5” HDD/SSD

2x mSATA slot up to 6 Gbps (SATA 3.0)

Graphics

GPU

Intel HD 4400 Graphics

Triple display mode supported

Display Interface 1

HDMI 1.4a up to 4096 x 2304 @ 24 Hz

Display Interface 2

DisplayPort 1.2 up to 3200 x 2000 @ 60 Hz

Display Interface 3

HDMI 1.4a up to 4096 x 2304 @ 24 Hz

Audio

Codec

Realtek ALC888-VC2 HD audio codec

Audio Output

Analog stereo output

Digital 7.1+2 channels S/PDIF output

3.5mm jack

Audio Input

Analog stereo Microphone input

Digital S/PDIF input

3.5mm jack

Networking

LAN

2x GbE LAN ports

LAN1: Intel I218 GbE PHY (MAC integrated into the chipset) (RJ-45)

LAN2: Intel I211 GbE controller (RJ-45)

Wireless

WLAN 802.11ac (2.4/5GHz dual band Intel 7260HMW)

Bluetooth 4.0

Connectivity

USB

4x USB 3.0

2x USB 2.0

Serial

3x Serial communication ports

COM0: Full RS232 via mini serial connector

COM1: 2-wire RS232 via mini serial connector

COM3: 2-wire RS232 via mini serial connector

SIM

1x micro SIM slot (6 pins)4

Special I/O

N/A

Expansion

Half-size mini-PCIe socket

Full-size mini-PCIe socket2

Advanced Technologies

vPRO

Yes (Intel vPRO Technology)5

AMT

Yes (Intel Active Management Technology)5

CPU Virtualization

Yes

Special Functionality

Auto-On

Wake-on-LAN

Wake-on-Timer

PXE Boot

Watchdog

Operating System

Supported

Windows 7/8, 32-bit and 64-bit

Linux 32-bit and 64-bit

Embedded OS

Operating Conditions

Input Voltage

Unregulated 10 –15VDC input1

Power Consumption

6W –24W

Operating Temperature

1. Commercial

HDD models: 0°C –50°C

SSD models: 0°C –70°C

2. Extended (TE)

SSD models only: -20°C –70°C

3. Industrial (TI)

SSD models only: -40°C –70°C

Enclosure

Material

Die Cast Aluminum

Cooling

Passive Cooling Fanless Design

Dimensions

19cm x 16cm x 4cm

Weight

1150gr

Package

Warranty

5 years3

Notes

1. Nominal input voltage: 12V

2. Shared with mSATA

3. For products purchased since 1-Jan-2013

4. For use with mini PCIe Cellular Modem module

5. Supported on LAN1 only

IPC2 features

Front panel

The features of the front panel of IPC2 depend on specific FACE Module used and are documented

separately.

Power

IPC2 has a tactile power push-button. It is used for turning on/off the PC and for standby/resume when

supported by the operating system.

A push of at least 5 seconds will always turn off the IPC2.

Display

IPC2 has triple display interface with support for triple head.

1. 2x HDMI with audio support

2. 1x DisplayPort

To connect IPC2 to a DVI display, use the provided HDMI to DVI-D adapter. Use a DVI cable to connect the

adapter to the display.

Audio

There are 2 standard 3.5mm jacks on the back panel.

Right:

Stereo line-in using a standard 3.5mm plug

S/PDIF 7.1 in using provided cable

Left:

Stereo line-out using a standard 3.5mm plug

S/PDIF 7.1 out using provided cable

LAN

IPC2 features two 10/100/1000BaseT Ethernet ports using standard RJ45 connectors. Use a standard

Ethernet cables to connect.

The connectors feature built-in LEDs that are lit when a connection is detected.

WLAN

2 WLAN antennas are supplied in models with integrated WiFi and should be screwed into the standard

SMA connectors.

USB

There are 2 USB 3.0 ports (5 Gbps) and 2 USB 2.0 ports on the back panel.

And additional 2 USB3.0 ports on the front panel.

All USB ports support current up to 1A.

Ports on the back are upside down –note when connecting USB plugs.

Serial port

Three RS232 mini-serial ports is located on the back panel.

Mini-serial to DB9 cable to connect to standard serial devices is supplied in the package.

Quick start guide

Connecting IPC2

Turn off the display and connect it to the IPC2 HDMI connector (use the HDMI to DVI adapter if

needed).

Connect the USB keyboard and mouse to USB 2 connectors.

Plug the Ethernet cable into the Ethernet connector.

In IPC2 models with WiFi: Mount the WiFi Antennas on the SMA connector by turning it clockwise

repeatedly until the antenna holds firm.

Insert the DC plug into the IPC2 DC-in jack. Rotate clockwise 900to secure.

Plug the speakers into the line-out jack.

Connect the power supply to the AC cord and plug the cord into AC outlet. The front panel logo

should light up as the IPC2 boots.

Booting Linux

Linux loads automatically on power up. Upon boot you will be guided through the Linux Mint first-boot

setup procedure.

Booting Windows 7

Upon first power-up, you will be guided through the Windows Welcome procedure which is self-

explanatory. The Windows 7 serial number is printed on the Windows 7 label on the bottom of your IPC2.

Maintenance

IPC2 requires no maintenance. You should not take the IPC2 apart other than opening the service door.

Taking IPC2 apart will void its warranty.

The following operations can be conducted by the user:

Opening service door

1. Unscrew marked Philips screw at the bottom to release service-door.

2. Slide out service-door until it stops –about 10 mm.

3. Service-door is now detached. Lift edge of service-door to completely remove.

Re-assemble in reverse order. Hard disk connects by sliding-in the service-door.

Service bay

The service-bay provides easy access to hard-disk, RAM, and mini-PCIe sockets incl. WLAN module.

Hard disk is 2.5” 7mm/9.5mm SATA. It is screwed to service door by 4 screws, 2 on each side. It is

recommended to use 5400 RPM hard disk or SSD. 7200 RPM or higher is not recommended due to higher

power consumption and risk of overheating.

RAM –use DDR3L-1333/1600 SO-DIMM modules.

Mini-PCIe –the half-size mini-PCIe is normally used for WLAN. If you remove the WLAN module make sure

to isolate the ends of antenna cables with some tape to avoid short-circuit. The full-size mini PCIe is

available for any use.

BIOS Setup Utility

Entering BIOS Setup Utility

Turn off the IPC2.

Turn on while holding down the F2 key.

See http://www.fit-pc.com/wiki/index.php/Main_Page.

Warranty and RMA

Warranty

CompuLab guarantees products against defects in workmanship and material for a period of 60

months from the date of shipment.

Your sole remedy and CompuLab’s sole liability shall be for CompuLab, at its sole discretion, to

either repair or replace the defective product at no charge.

This warranty is void if the product has been altered or damaged by accident, misuse or abuse.

RMA

Keep the original package for shipping in case of hardware failure.

In case of HW failure of an IPC2 under warranty, please contact the seller of that IPC2.

Please provide the following required information:

IPC2 serial number

Name of purchaser

Address

Problem description

If the IPC2 was purchased directly from CompuLab, please email rma@fit-pc.com.

Tips for saving power

General

Working without a connected display automatically disables the graphics controller –saving

power.

Disconnect external USB devices when not in use.

In Operating System

Use power scheme as follows

Turn of monitor after several minutes not in use

Turn off hard disk after several minutes not in use

System standby after an hour not in use

IPC2

Manufacturer: CompuLab Ltd.

This device complies with Part 15 of the

FCC Rules.

Operation is subject to the following two

conditions:

(1) This device may not cause harmful

interference, and

(2) This device must accept any

interference received, including

interference that may cause undesired

operation.

Statement

Changes or modifications to this

equipment not expressly approved by the

party responsible for compliance

(CompuLab Ltd.) could void the user’s

authority to operate the equipment.

Statement

NOTE: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and

receiver.

-Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician

for help.

Table des matières

Autres manuels CompuLab Ordinateur de bureau

CompuLab

CompuLab Fitlet FC-OPLN Manuel utilisateur

CompuLab

CompuLab Fitlet2 FC-POED Manuel utilisateur

CompuLab

CompuLab Airtop3 Manuel utilisateur

CompuLab

CompuLab Airtop2 Manuel utilisateur

CompuLab

CompuLab SBC-FITPC3 Manuel utilisateur

CompuLab

CompuLab FIT-PC4 Manuel utilisateur

CompuLab

CompuLab Airtop-C0 Manuel utilisateur

CompuLab

CompuLab fit-PC2i Manuel utilisateur

CompuLab

CompuLab fit-PC2 Manuel utilisateur

CompuLab

CompuLab IPC3 Manuel utilisateur

CompuLab

CompuLab Airtop Manuel utilisateur

CompuLab

CompuLab fitlet2 FC-USB Manuel utilisateur

CompuLab

CompuLab Fitlet-H Manuel utilisateur

CompuLab

CompuLab Tensor-I22 Manuel utilisateur

CompuLab

CompuLab fitlet3 Manuel utilisateur

CompuLab

CompuLab UTILITE2 Manuel utilisateur

CompuLab

CompuLab fitlet2 FC-USB Manuel utilisateur

CompuLab

CompuLab Trim-Slice Manuel utilisateur

CompuLab

CompuLab fitlet2 FC-USB Manuel utilisateur

CompuLab

CompuLab fitlet Manuel utilisateur

Manuels Ordinateur de bureau populaires d'autres marques

HP m9060n - Pavilion - Elite Fiche technique

Asus

Asus E210 Series Manuel utilisateur

Dell

Dell Inspiron 600m Manuel utilisateur

Dell

Dell Inspiron 3662 Manuel utilisateur

TotalFlow

TotalFlow uFLO Manuel utilisateur

HP Presario SV7000 - Desktop PC Manuel utilisateur

HP ProDesk 400 G5 Manuel

Logitech

Logitech MK320 Manuel utilisateur

Dell

Dell XPS 730 H2C Manuel utilisateur

Sony

Sony Vaio Series Manuel utilisateur

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuel utilisateur

Alto

Alto MD 250 Manuel utilisateur

Lenovo

Lenovo ThinkCentre Edge 72 Manuel

Lenovo

Lenovo ThinkStation D20 Manuel

Arbor Technology

Arbor Technology FPC-7800 Series Manuel utilisateur

Sony

Sony VAIO VGX-TP1 Series Manuel utilisateur

Asus

Asus Eee Box B204 Manuel utilisateur

Dell

Dell Optiplex 9010 All In One Manuel utilisateur