Component Playgrounds HL55-10 Manuel utilisateur

Installation Instructions

HL55-10

Required Crew: 2 Required but 4 Recommended

Concrete: 12-16, 80 lb. bags

Required Tools:

● Wheelbarrow

● Step Ladder (6’ or taller)

● Shovel

● Tape Measure

● Digging Bar or Pick

● Level

● Allen Wrench (Provided)

● Open end or Box Wrenches: 9/16”, ¾”

● Hammer or Mallet

● Ratchet Handle & Sockets: 9/16”, ¾”

● Marker Pen

● Drill: Cordless or electric, or impact driver

Component Playgrounds is concerned about the safety of your vision. It

is important that you choose to protect your vision by wearing proper

safety glasses during each and every phase of this construction

process.

PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING

The HL55-10 can be installed as a one day project. The normal time

required to install the HL55-10 is about 3-6 hours for a two man crew. This

time requirement will vary dependent upon the composition of the soil and

the speed of the installers. Mix and pour the concrete as the last step.

*Before digging, please obey local laws by notifying your local

underground utilities marking organization*

Installation Instructions

1. Select an area in your yard that is reasonably level and meets the space

requirements for your equipment. Ground Space: 9’ x 28’ Play Space: 13’ x

39’.

2. Using the measurements from the top view diagram, measure and mark

the position of the Swing Hangers and Ladders on both 9’ Top Rails. Place

the Horizontal Ladder on to the ground in the desired location with Top

Rails in the correct position on the ground. (Measure and adjust the

Horizontal Ladder on the ground as necessary to provide for the proper

play space.)

3. Move 9’ Top Rails and set aside.

4. With the Horizontal Ladder in its proper position, mark the locations for

the holes where the two Upright Ladders will stand.

5. Move the Horizontal Ladder and dig the holes (see #1A hole sizes for

cementing).

6. Lay each Upright Ladder on the ground near the hole where it will

eventually stand. Make a mark 15” from the top of the 8’ Upright Ladder

onto each Ladder Rail. Make a mark 39” from the top of the 10’ Upright

Ladder onto each Ladder Rail.

7. Move the Adjustable Sleeves to these marks and position them to

receive the Horizontal Ladder. On the 10’ Upright Ladder, this is

accomplished by turning them to point at a 90 degree angle towards what

will become the inside of the structure. (The rungs and the Third Leg Bolt

will be attached to what will become the outside of the structure.)

8. On the 8’ Upright Ladder (the Slide will attach to this Ladder), repeat the

process similarly as on the other Ladder. However, the Adjustable Sleeves

should point toward, and the rungs are welded on what will become the

inside of the structure. This will make it easier to climb up the Ladder to the

Slide. Secure set screws.

9. Place the Upright Ladders onto their sides with the bottom of the pipe

just over the hole where it will eventually stand. Attach the Horizontal

Ladder to the Adjustable Sleeves of the Upright Ladders and secure the set

screws (see #3 Horizontal Ladder to Upright Ladder assembly). Hint: Do

not push Horizontal Ladder tight against the Upright Ladders. Leave a 1⁄2” -

1” gap between the Upright Ladder rails and the Horizontal Ladder. This

will allow for easier adjustment of the Horizontal Ladder in the future.

10. Using two strong adults, stand the assembled Horizontal Ladder set

into the holes.

11. Install plugs into the ends of the Top Rails.

12. Slide Top Rails into Top Sleeve of the Upright Ladders (see #2 Ladder

to Top Rail assembly). Secure set screws.

13. Slide 3rd leg sleeve onto the top rail that is sleeved into the 10’ ladder.

14. Measure 5 1⁄2’ - 6’ away from the 10’ Upright Ladder to mark and dig

the hole for the Third Leg (see #1B hole sizes for cementing).

15. Before installing the third leg, locate the third leg. Insert 3⁄8” x 31⁄2” Hex

Bolt and loosely thread 3⁄8” Nut into the bottom hole. Nut will not thread all

the way on and bolt will be loose. (This is to act as an anchor in the

concrete and does not need to be tight.)

16. Install Third Leg by dropping the end into the hole and sliding the top

into the 3rd leg sleeve. Use the 3/8” x 2 3/4” hex bolt and 3/8” nyloc nut.

Then secure 3rd leg with set screw on under side. (see diagram #4) When

properly positioned, secure the set screws in the top of the 3rd leg sleeve.

17. Assemble and attach Swing Hangers to Top Rail (see swing hanger

assembly sheet).

18. Attach swing chains, seats, trapeze bar and rings.

19. Attach the Slide onto the 8’ Ladder (see Slide Assembly instruction

sheet).

20. Measure the height of the Top Rails to insure proper swing height.

21. Level the swing set.

22. Mix concrete according to package directions and pour the appropriate

quantities into each hole.

23. Allow cement to cure for 3-5 days and enjoy your Component

Playground.

#1 Holes Sizes for Cementing in the Set

#2 Ladder to Top Rail Assembly

#3 Horizontal Ladder to Upright Ladder Assembly

#4 Third Leg Sleeve

1. Loosen and remove the two nyloc jam nuts.

2. Reassemble on to swing top rail. The hex bolt can be positioned as it is

pictured or flipped around so the hex holt is on the bottom. Tighten securely so

that the hanger is firmly attached in place and cannot slide or swivel along top

rail.

3. Attach carabineer with chain through the ring.

Note: We recommend you check the pendulum in the swing hangers at

least every 6 months for normal wear.

Rocket Slide Mounting Instructions

Read Before Use

Congratulations! You have just purchased one of the finest pieces of playground equipment available.

Your family will enjoy many hours of fun with this fine equipment. Playground equipment can be most

enjoyable, but there are some dangers if not used properly. You should be aware of the following:

Equipment should be installed in a level area, free from obstructions, with enough space to allow for

adequate clearance in all directions when equipment is in maximum use.

Keep objects away from equipment that could interfere with persons using it or that could be hazardous.

Misuse or abuse of this playground equipment is dangerous and can cause serious injury.

This equipment should be inspected before each use and any worn, defective or missing parts should be

replaced.

Children should play on equipment only with adult supervision and should be duly warned of the potential

hazards in this type of equipment when used improperly. Children should be instructed as to proper

caution to take in its use.

Equipment should NOT be used when it is wet or icy.

Equipment should only be used in a well-lit area.

Do NOT use equipment when tired, under stress or emotionally upset.

Do NOT overcrowd.

Do NOT use equipment when under the influence of alcohol or drugs.

Do NOT attempt somersaults or gymnastic stunts on or using this equipment.

Know your own limitations and exercise caution at all times.

Do not jump off of equipment when dismounting. It is a dangerous practice to jump on or off equipment.

Do not attempt to use equipment for something other than the use for which it was designed and

intended, or in a manner other than that for which it was designed and intended.

While every attempt is made by Component Playgrounds to ensure the highest degree of

safety in all of our equipment, we cannot guarantee freedom from injury. The user

assumes all risk of injury due to use. All merchandise is sold on this condition, which no

representative of the company can waive or change.

Maintenance of your playground

We hope that you and your family will enjoy many hours of great family fun while using your

Component Playgrounds Products. We appreciate your business. Our goal is to provide safe,

durable and fun products using the best materials available. Your product should be mostly

maintenance free. However, you should consider the following suggestions with regard to the

up keep of your new swing set.

1. Chains and Connectors: The chains are coated with the highest quality bright zinc

coating and the highest quality polymer coatings available. However, over time the

zinc coating may become discolored or eventually have surface rust appear. The

polymer coating may also become discolored with time and may eventually crack. This

depends mostly upon environmental conditions and normally will not affect the

durability and safety of the product. However, these items should be inspected

regularly for excessive wear and should be replaced as necessary.

2. Swing Hangers: These items are coated with a high quality galvanizing. However,

swing hangers may become discolored or may eventually rust. Should this happen, a

touch up using a cold galvanizing compound followed by a coat of silver aluminum spray

paint will make them look new again. These items can be purchased in aerosol cans

(“spray paint”) at most hardware stores and at Component Playgrounds. The brass

bushings inside of the swing hanger are impregnated with lubricant and will not

generally require any further lubrication. However, these should be periodically

inspected for wear and replaced as necessary. Note: Twisting the chains while swinging

will put extra wear on the swing hanger parts. If your children enjoy this practice, please

inspect the swing hangers more frequently.

3. Tire Swing Knuckles (for sets with a tire swing): The tire swing knuckle arrives at

Component Playgrounds pre-lubricated from the manufacturer. However, it is good

practice to inspect the knuckle and be sure that there is adequate lubrication before it

is used for the first time. After that, the tire knuckles should be lubricated at least twice

annually to prevent excessive wear and the eventual failure of the tire swing knuckle.

4. Welds: The heat from the welding process will damage the galvanizing that is on the

pipe when it arrives to us from the manufacturer. This damage to the galvanizing is

restricted to the actual weld. When your equipment is built, Component Playgrounds

will repair this damage using a cold galvanizing compound spray along with a top coat

of silver aluminum. This is a time tested and durable process. However, when you are

inspecting your playground equipment, if you notice that some surface rust has

appeared on the welds, simply apply a fresh coat of the cold galvanizing compound

and the silver aluminum top coat to keep your structure looking new. (These spray

products

can be purchased in aerosol cans (“spray paint”) at most hardware stores and

at Component Playgrounds.)

5. Plastic Lumber Platforms: If you have purchased a structure which includes a

platform, the plastic lumber does not need to be finished or stained. It is 100%

maintenance free. However, you may need to occasionally hose it down to remove

dirt and other debris that may collect after many hours of use by happy children.

6. Vinyl Canopies: If you have purchased a structure which includes a vinyl canopy, this

product should be inspected occasionally for wear and will need to be replaced as

necessary. Depending upon your environmental conditions, the normal life

expectancy of the vinyl canopy is 3 – 5 years.

7. Swing Seats: These should be inspected at least twice annually and should be replaced

as necessary.

8. Slides: Slides should never be lifted at the bottom. Lifting the slide at the bottom will

almost always cause the slide to crack at the top where it has been attached to

the platform or bracket. Cracks and wear such as is caused by this practice are

easily identifiable and will not be covered under the product warranty.

Slides should be inspected at least annually to ensure that the sliding surface is in

good condition. Also inspect the side rails to be sure that the plastic has not been cut

or gouged in any manner which would present the risk of injury while sliding.

9. Fasteners: All fasteners should be periodically inspected to make certain that they are

tight and secure. Re-secure as

necessary.

*For Safety please inspect all moving parts on a regular basis. (At Least Yearly)

Especially paying attention to wear within the swing hanger.

Table des matières

Autres manuels Component Playgrounds Équipements de jeux et d'aires de jeux

Component Playgrounds

Component Playgrounds CH35 Manuel utilisateur

Component Playgrounds

Component Playgrounds PH30 Swing Set Manuel utilisateur

Component Playgrounds

Component Playgrounds SS47-10 Manuel utilisateur

Component Playgrounds

Component Playgrounds AR40-10 Manuel utilisateur

Component Playgrounds

Component Playgrounds CP-PS36-8 Manuel utilisateur

Component Playgrounds

Component Playgrounds AR20-10 Manuel utilisateur

Component Playgrounds

Component Playgrounds PH52 Manuel utilisateur

Component Playgrounds

Component Playgrounds Super Swing w/ Tire Manuel utilisateur

Component Playgrounds

Component Playgrounds ST30 Manuel utilisateur

Component Playgrounds

Component Playgrounds A-Frame Junior Manuel utilisateur

Component Playgrounds

Component Playgrounds HL50-10 Manuel utilisateur

Component Playgrounds

Component Playgrounds PH35-10 Manuel utilisateur

Component Playgrounds

Component Playgrounds Super Swing w/ Slide Manuel utilisateur

Component Playgrounds

Component Playgrounds Super Swing w/ Slide and Buoy Ball Manuel utilisateur

Component Playgrounds

Component Playgrounds SS38-10 Manuel utilisateur

Component Playgrounds

Component Playgrounds AR20 Manuel utilisateur

Component Playgrounds

Component Playgrounds ST20 Manuel utilisateur

Component Playgrounds

Component Playgrounds PH45 Manuel utilisateur

Component Playgrounds

Component Playgrounds HL50 Manuel utilisateur

Component Playgrounds

Component Playgrounds HL55 Manuel utilisateur

Component Playgrounds

Component Playgrounds Swing Set PH35-10 Manuel utilisateur

Component Playgrounds

Component Playgrounds MT40 Manuel utilisateur

Manuels Équipements de jeux et d'aires de jeux populaires d'autres marques

Ledon

Ledon 302040 Manuel utilisateur

FUNormous

FUNormous Disney Junior MICKEY MOUSE Manuel utilisateur

b4Adventure

b4Adventure Slackers TREEZONE ADVENTURE THREE HOUSE Manuel utilisateur

PoolMaster

PoolMaster 72775 Manuel utilisateur

Palmako

Palmako 4743142009857 Manuel de l'installateur

BOERPLAY

BOERPLAY PSTE000.019 Manuel utilisateur

MGA Entertainment

MGA Entertainment Little Tikes Dunk'n Toss Bouncer Guide de l'utilisateur

stilum

stilum Erika Manuel utilisateur

Costway

Costway NP10816 Manuel utilisateur

Trigano

Trigano VABI Manuel utilisateur

Outward

Outward OUT116 Manuel utilisateur

GALOPIN

GALOPIN ARC02 Manuel utilisateur

stilum

stilum levis Caractéristiques techniques

Ledon

Ledon BASIC Bai LB012 Manuel utilisateur

BOERPLAY

BOERPLAY PSTE115.002 Manuel utilisateur

Europlay

Europlay S306 Manuel de programmation

SportsPlay Equipment

SportsPlay Equipment 361-509H Manuel utilisateur

Ledon

Ledon 302250 Manuel utilisateur