Compliance West HT-2000 Manuel utilisateur
Fast Charge Option
(IEC 335)
MegaPulse Surge Testers
Instruction Manual
COMPLIANCE
WESTUSA
Dear Customer:
Congratulations! Compliance West USA thanks you for
purchasing the Fast Charge option for our MegaPulse family of
surge testers. Connection of this option will allow the MegaPulse
to charge within the minimum time constraints as dictated by
relevant Standards pertaining to the MegaPulse you have
purchased.
In order to use this option safely, we urge you to carefully review
this manual before connection to your MegaPulse tester. Both
line voltage and high voltage secondary circuits could be
contacted if this option is improperly connected, and contact with
either of these circuits pose the risk of serious injury or death.
Compliance West USA stands by your instrument with a full one-
year warranty and free lifetime technical support. If the need
arises, please don't hesitate to call on us.
Thank you for your trust and confidence.
Rev. 1.0 May 12, 2005 i
Table of Contents
MegaPulse Fast Charge Option (IEC 335).................................................................................................1
General Information.....................................................................................................................1
Description.................................................................................................................................................3
Installation..................................................................................................................................................7
Testing for Proper Operation .......................................................................................................7
Removal of the Fast Charge Option.............................................................................................7
Technical Assistance..................................................................................................................................9
Table of Figures
Figure 1 Fast Charge Option (IEC 335) Front Panel...................................................................................... 4
Figure 2 MegaPulse Fast Charge Option Connector...................................................................................... 5
Figure 3 MegaPulse Option Connector Cover ............................................................................................... 6
Table of Tables
Table 1 Fast Charge Option (IEC 335) Front Panel....................................................................................... 4
Table 2 MegaPulse Fast Charge Option Connector ....................................................................................... 5
ii
iii
Section 1
MegaPulse Fast Charge Option (IEC 335)
General Information
The MegaPulse Fast Charge Option allows the host MegaPulse tester to charge quickly enough to
satisfy minimum repetition times for tests within particular Standards. In this case, IEC 335 requires
multiple surges to be applied to the EUT with a minimum pause time of 3 seconds between pulses, and the
Fast Charge Option designed to allow recharging to the full capabilities of the tester within that time.
There are no adjustments or controls on the Fast Charge Option (IEC 335). If the option is
connected to the MegaPulse tester, the Fast Charge Option is operational.
Operation of the MegaPulse is the same whether the Fast Charge Option (IEC 335) is connected
or disconnected. Set the voltage knob for the voltage desired, press Charge, then press Trigger. See the
MegaPulse Tester manual for more information on its operation.
Connection of the Fast Charge Option (IEC 335) is simple and straightforward, but for operator
safety during installation, the Installation Instructions in Section 3 must be followed. It is imperative that
ALL connections between the Fast Charge Option (IEC 335) and the MegaPulse tester be made, and the
Connection Cover secured, before the MegaPulse is connected to line voltage. If the Fast Charge Option
(IEC 335) is disconnected, please disconnect the MegaPulse from line voltage first.
Once connected, the Fast Charge Option does not pose the risk of shock. However, both line
voltage and high voltage secondary circuits exist in the connections between the two enclosures. Exercise
care with these wires and inspect them for damage periodically.
This manual contains a general description of the option (above), installation and removal
instructions, and support information. For further information regarding operation of the MegaPulse
Tester, please see the MegaPulse Tester Manual.
1
Section 2
Description
The Fast Charge Option (IEC 335) contains an
auxiliary AC power supply which allows the
MegaPulse it is connected to to charge within 3
seconds as required for the minimum rest time
between repetitive cycles.
MegaPulse operation is identical whether the
Fast Charge Option (IEC 335) is connected or
not. Charge times to 12kV are approximately 12
seconds without the Option, and approximately
2-1/2 seconds with the Option installed.
Connection points on the Fast Charge Option
(IEC 335) front panel are noted in Figure 1 and
Table 1. All cables are supplied with the
Option, and cable use is also documented in
Table 1.
MegaPulse testers are supplied with a covered
connection terminal enclosure on its rear panel.
A photo of this enclosure and connection points
on the MegaPulse rear panel are noted in Figure
2 and Table 2.
After connection or disconnection of the Fast
Charge Option (IEC 335), the Connector Cover
on the rear panel of the MegaPulse must be
replaced using the four provided screws before
the MegaPulse is energized. Fig. 3 shows the
cover correctly installed.
3
4
Figure 1 Fast Charge Option (IEC 335) Front Panel
ITEM NAME FUNCTION AND CONNECTION MEANS
1 Low Voltage Connection A Line Voltage A connection from MegaPulse: Separate BLACK lead
2 Low Voltage Connection B Line Voltage B connection from MegaPulse: Separate RED lead
3 Ground Lug Ground Connection point (from MegaPulse ground): Green wire terminated in closed loop connectors
4 High Voltage Connection 1 High Voltage connection 1 to MegaPulse: Pigtail from Fast Charge Option (IEC 335)
5 High Voltage Connection 2 High Voltage connection 2 to MegaPulse: Pigtail from Fast Charge Option (IEC 335)
Table 1 Fast Charge Option (IEC 335) Front Panel
Figure 2 MegaPulse Fast Charge Option Connector
ITEM NAME FUNCTION AND CONNECTION MEANS
1 High Voltage Connection 1 High Voltage 1 connection from Option: Pigtail 1 from Option
2 High Voltage Connection 2 High Voltage 2 connection from Option: Pigtail 2 from Option
3 GROUND Grounding connection point: Connect green wire from Option ground here
4 Low Voltage Connection A Line Voltage A connection: Use separate BLACK lead
5 Low Voltage Connection B Line Voltage B connection: Use separate RED lead
Table 2 MegaPulse Fast Charge Option Connector
5
Figure 3 MegaPulse Option Connector Cover
6
Table des matières
Autres manuels Compliance West Équipement de test
Compliance West
Compliance West MegaPulse Defib-5PF-002 Manuel utilisateur
Compliance West
Compliance West MegaPulse Capacitor A PF Series Manuel utilisateur
Compliance West
Compliance West HT-2000PR Manuel utilisateur
Compliance West
Compliance West HT-20KVPac Manuel utilisateur
Compliance West
Compliance West CDT-240 Manuel
Compliance West
Compliance West CDT-240 Manuel d'utilisation et d'entretien
Compliance West
Compliance West CDT-240 Manuel utilisateur
Compliance West
Compliance West MegaPulse Antenna Surge PF 65 Manuel utilisateur
Compliance West
Compliance West HT-10KVDC Manuel utilisateur
Compliance West
Compliance West HT-2800 Manuel utilisateur
Compliance West
Compliance West MegaPulse 360 Manuel utilisateur
Compliance West
Compliance West GFM-200A Manuel utilisateur
Compliance West
Compliance West MegaPulse D5-PF Manuel utilisateur
Compliance West
Compliance West MegaPulse 1.2x50/8x20-2PF-HR Manuel utilisateur
Compliance West
Compliance West HTT-1R Manuel utilisateur
Compliance West
Compliance West HTT-1S Manuel utilisateur
Compliance West
Compliance West MegaPulse 10x700-7PF Manuel utilisateur
Compliance West
Compliance West MegaPulse Manuel utilisateur
Compliance West
Compliance West HT-25KVP dc Manuel utilisateur
Compliance West
Compliance West HT-2800P Manuel utilisateur
Manuels Équipement de test populaires d'autres marques
SMART
SMART KANAAD SBT XTREME 3G Series Manuel utilisateur
Agilent Technologies
Agilent Technologies BERT Serial Manuel utilisateur
Agilent Technologies
Agilent Technologies N3280A Manuel utilisateur
Vernier
Vernier Go Direct Voltage Manuel utilisateur
Lifeloc
Lifeloc R.A.D.A.R. Manuel utilisateur
Fluke
Fluke T5-600 Instructions d'utilisation et d'installation
