Compaq 1850R - ProLiant - 128 MB RAM Guide de démarrage rapide

Technical Guide

April 1999

ECG062/0299

Prepared by High Availability Group

Compaq Computer Corporation

Contents

Introduction................................3

Communication points of

failure..........................................4

Supported Non-Fault

Tolerant Architectures ...............5

Supported Fault Tolerant

Architecture................................6

Teaming Configuration for

Higher Availability......................8

Hardware and Software

Requirements...........................8

Teaming Configuration of

Ethernet Interconnects for

Compaq Fast Ethernet NC

Series NIC cards.........................9

Option 1. NIC Fault

Tolerance (NFT)

Configuration............................9

Option 2. Adaptive Load

Balancing (ALB)

Configuration............................9

Steps for Configuring NICs

Utilizing Teaming....................10

Verifying Client LAN and

Cluster Interconnect IP

Addresses ................................16

Supported Ethernet Interconnects for

Compaq Parallel Database Clusters

using Oracle Parallel Server

Abstract:

This Technical Guide reviews the supported Ethernet client LAN and

cluster interconnect options for the Compaq Parallel Database

Clusters for Oracle Parallel Server. Both redundant and non-

redundant configurations are discussed. Hardware and software

requirements along with limitations are detailed. The recommended

cluster interconnect architecture is a fully redundant, and therefore

highly available configuration.

Supported Ethernet Interconnects for Compaq Parallel Database Clusters using Oracle Parallel Server 2

ECG062/0299

Notice

The information in this publication is subject to change without notice and is provided “AS IS” WITHOUT

WARRANTY OF ANY KIND. THE ENTIRE RISK ARISING OUT OF THE USE OF THIS

INFORMATION REMAINS WITH RECIPIENT. IN NO EVENT SHALL COMPAQ BE LIABLE FOR

ANY DIRECT, CONSEQUENTIAL, INCIDENTAL, SPECIAL, PUNITIVE OR OTHER DAMAGES

WHATSOEVER (INCLUDING WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS

PROFITS, BUSINESS INTERRUPTION OR LOSS OF BUSINESS INFORMATION), EVEN IF

COMPAQ HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

The limited warranties for Compaq products are exclusively set forth in the documentation accompanying

such products. Nothing herein should be construed as constituting a further or additional warranty.

This publication does not constitute an endorsement of the product or products that were tested. The

configuration or configurations tested or described may or may not be the only available solution. This test

is not a determination or product quality or correctness, nor does it ensure compliance with any federal

state or local requirements.

Product names mentioned herein may be trademarks and/or registered trademarks of their respective

companies.

Compaq, Contura, Deskpro, Fastart, Compaq Insight Manager, LTE, PageMarq, Systempro, Systempro/LT,

ProLiant, TwinTray, ROMPaq, LicensePaq, QVision, SLT, ProLinea, SmartStart, NetFlex, DirectPlus,

QuickFind, RemotePaq, BackPaq, TechPaq, SpeedPaq, QuickBack, PaqFax, Presario, SilentCool,

CompaqCare (design), Aero, SmartStation, MiniStation, and PaqRap, registered United States Patent and

Trademark Office.

Netelligent, Armada, Cruiser, Concerto, QuickChoice, ProSignia, Systempro/XL, Net1, LTE Elite,

Vocalyst, PageMate, SoftPaq, FirstPaq, SolutionPaq, EasyPoint, EZ Help, MaxLight, MultiLock,

QuickBlank, QuickLock, UltraView, Innovate logo, Wonder Tools logo in black/white and color, and

Compaq PC Card Solution logo are trademarks and/or service marks of Compaq Computer Corporation.

Microsoft, Windows, Windows NT, Windows NT Server and Workstation, Microsoft SQL Server for

Windows NT are trademarks and/or registered trademarks of Microsoft Corporation.

NetWare and Novell are registered trademarks and intraNetWare, NDS, and Novell Directory Services are

trademarks of Novell, Inc.

Pentium is a registered trademark of Intel Corporation.

Oracle8 is a trademark and Oracle is a registered trademark of Oracle Corporation.

First Edition (April 1999)

Document Number ECG062/0299

Supported Ethernet Interconnects for Compaq Parallel Database Clusters using Oracle Parallel Server 3

ECG062/0299

Introduction

This Technical Guide is intended to be a supplement to the Order and Configuration Guides,

Administrator Guides, and Certification Matrix for the Compaq Parallel Database Clusters for

Oracle Parallel Server (OPS). This Guide reviews the supported Ethernet architectures for the

client LAN and cluster interconnect (sometimes known as SAN) in an OPS environment. It does

not provide detailed cluster network configuration information, nor does it address the ServerNet

interconnect options available. Please refer to your Order and Configuration Guide and

Administrator Guide for the configuration and implementation of these architectures.

The client LAN and cluster interconnect used in a Compaq Parallel Database Cluster environment

can be a combination of redundant or non-redundant architectures. This document begins with a

brief discussion of the non-redundant architecture for both the client LAN and cluster

interconnect. Limitations and requirements are outlined.

Two options are detailed for implementation of fully redundant client LAN and cluster

interconnect connections - NIC Fault Tolerant (NFT) and Adaptive Load Balancing (ALB). The

ALB option is recommended for the best performance and availability of your cluster. Both

configurations are fully tested and supported. These architectures will be defined for hardware,

software and configuration requirements. These are the recommended configurations for the

Compaq Parallel Database Clusters for OPS.

Supported Ethernet Interconnects for Compaq Parallel Database Clusters using Oracle Parallel Server 4

ECG062/0299

Communication points of failure

Several components make up the physical network of the client LAN and cluster interconnect

communication paths. The failure of any one of these components renders the entire path

inoperable. Unless redundancy has been designed into the communication paths, a component

failure can cause a complete disruption of access to certain cluster resources.

The following four hardware items are the primary points of possible failure.

•A port on a dual-ported network controller (LAN or cluster interconnect)

•An entire network controller (LAN, cluster interconnect or a combination of both)

•A network cable

•A port on a switch

•A switch

An integration of hardware and software technologies can create redundancy to maintain a robust

cluster, thus supplying defenses against points of failure in the architecture. This increases both

the resiliency of cluster communications, and the overall availability of cluster applications and

data.To protect against any communication disruption, Compaq highly recommends you

implement the fully redundant communications paths specified in this document. The following

are the redundancy characteristics of both the cluster interconnect and the client LAN connections

in the fully redundant configurations recommended in the following sections.

The cluster interconnect remains available if:

a network controller port used for the primary interconnect path fails.

a network controller used for the primary interconnect path fails.

the network cable(s) used for the primary interconnect path fails.

the port(s)on the switch used for the primary interconnect path fails.

the switch used for the primary interconnect path fails.

Point(s) of Failure: None, if all client connections to the cluster interconnect switch are

redundant.

The client LAN remains available if:

a network controller port used for the primary client LAN path fails.

a network controller used for the primary client LAN path fails.

the network cable(s) used for the primary client LAN path fails.

the port(s) on the switch used for the primary client LAN path fails.

the switch used for the primary interconnect path fails.

Point(s) of Failure: None, if all client connections to the client LAN switch are redundant.

Supported Ethernet Interconnects for Compaq Parallel Database Clusters using Oracle Parallel Server 5

ECG062/0299

Supported Non-Fault Tolerant Architectures

A non-fault tolerant architecture means that your cluster will have at least one point of failure in

the communications network. Certain non-fault tolerant Ethernet architectures are supported.

For two node configurations, the use of a simple crossover cable is one of the supported options.

See Figure 1 for an illustration of this option.

NOTE: Redundant crossover cables are NOT supported.

A single path connection through a hub or switch is also a supported two node non-fault tolerant

configuration.

For more than two node configurations, a switch is required. (It doesn’t necessarily need to be

fully redundant to be supported.)

CROSS-OVER CABLE

SAN

SERVER-2

Port-1

NIC NIC

LAN

ENET SWITCH/HUB

To public LAN (Clients)

SERVER-1

Figure 1. Example of a non-fault tolerant, 2-node configuration

using a cross-over cable

Port-2 Port-2

Port-1

Supported Ethernet Interconnects for Compaq Parallel Database Clusters using Oracle Parallel Server 6

ECG062/0299

Supported Fault Tolerant Architecture

A fault tolerant architecture consists of combining Microsoft NT and Compaq software with

Compaq Fast Ethernet Network Interface Controllers (NICs) in the Compaq NC Series, to create

redundancy. With this configuration, two NICs can be configured for a fault tolerant network

with a path for primary and a path for secondary or backup communication on separate NICs

(either dual or single port), for each node. This path/port teaming feature is enabled with a

Compaq utility in the Microsoft Windows NT 4.0 network control panel.

Several configurations are supported for the cluster interconnect and the client LAN. In this

document, only the most robust configuration that will provide both the highest availability and

performance is recommended (See Figure 2). (This document will address redundancy in both the

LAN and cluster interconnect. It is not required that both networks be fully redundant to be

supported, any combination will work as well.)

The following configuration can be achieved using either two dual-port NICs or four single-port

NICs or a combination of the two in each server. Two switches for the cluster interconnect and

two hubs or switches for the client LAN connections are shown here. This configuration is the

recommended architecture for optimal fault.

ENET SWITCH-2

ENET SWITCH-1

TEAM-A TEAM-A

SAN

SERVER-N

N::::::::::::::::::::::::::::::::::

Port-1 Port-1

Port-2 Port-2

NIC NIC NIC NIC

TEAM-B LAN TEAM-B

ENET SWITCH/HUB-1

ENET SWITCH/HUB-2

To public LAN (Clients)

SERVER-1

Figure 2. Fault Tolerant Configuration

Supported Ethernet Interconnects for Compaq Parallel Database Clusters using Oracle Parallel Server 7

ECG062/0299

Implementing this configuration in the NT environment is achieved through the use of an NT

networking feature known as “port teaming”. Port teaming is defined as combining or merging of

ports to create a standby or active alternate communication path. Follow the instructions below to

create a fully redundant and highly available communications network:

Step 1. Connect the top port (Port-1) of one NIC in each server to the first cluster interconnect

switch (Enet Switch-1).

Step 2. Connect the top port (Port-1) of the other NIC in each server to the second cluster

interconnect switch (Enet Switch-2).

Step 3. Connect the bottom port (Port-2) of one NIC in each server to the first public client LAN

switch (Enet Switch/Hub-1).

Step 4. Connect the bottom port (Port-2) of the other NIC in each server to the second public

client LAN switch (Enet Switch/Hub-2).

Refer to the “Steps for configuring NICs utilizing teaming” portion of this document for the

step-by-step teaming instructions.

•Assign the top ports of both NICs in each server to one team (“TEAM-A” see Figure 2.)

•Assign the bottom ports of both NICs in each server to one team (“TEAM-B” see Figure 2.)

NOTE: For the teaming option, the Adaptive Load Balancing (ALB) is strongly recommend — it increases

the transmission throughput by supporting up to four NIC teams, with two or four NICs per team.

Supported Ethernet Interconnects for Compaq Parallel Database Clusters using Oracle Parallel Server 8

ECG062/0299

Teaming Configuration for Higher Availability

Hardware and Software Requirements

•Hardware

To create a fault tolerant configuration of the cluster, the redundancy option of Compaq’s Fast

Ethernet dual-redundant NC series NIC cards is required. To use this function, two dual-port or

four single-port (or a combination of both) NICs are required for each server in the cluster.

For the cluster interconnect connection, two network switches are required. Two hubs may be

used in a two node configuration. For better performance, the hubs should be replaced by

switches when a third node is added.

•Software

Oracle Software

Contact Oracle Corp. for all Oracle software.

Compaq Software

Contact Compaq Corp. for Compaq Parallel Database Cluster software and the latest drivers of

the Compaq Fast Ethernet NC series NIC cards.

Microsoft SP4 for Windows NT 4.0

To implement the dual redundant option of the Fast Ethernet NIC cards, Microsoft SP4 for

Windows NT 4.0 is highly recommended. Install SP4 prior to utilizing the NIC teaming option.

Contact Microsoft for this software.

After you team your NICs, you must ensure that the binding order of the ports are correct. This is

explained later in the guide.

Note: If you are required to use SP3 (which is not recommended), please contact Lino Costantino

@ Compaq Corp. at (408) 285-6983 or [email protected].

Supported Ethernet Interconnects for Compaq Parallel Database Clusters using Oracle Parallel Server 9

ECG062/0299

Teaming Configuration of Ethernet Interconnects for

Compaq Fast Ethernet NC Series NIC cards

To achieve higher availability in a cluster, the enhanced dual redundant features of Compaqs Fast

Ethernet NICs are required.

The dual redundancy option of the Fast Ethernet NICs are achieved by assigning individual

NICs/ports to a team. Microsoft Windows NT 4.0 Service Pack 4 (SP4) is required for

implementing NIC teaming properly. This “teaming” configures the ports as primary and

secondary (or backup) ports with a common IP address. After building a team, identify the type of

team (NFT or ALB).

For the best teaming option, the Adaptive Load Balancing (ALB) is strongly recommended —

ALB increases transmission throughput by supporting up to four NIC teams, with two or four

NICs per team. NICs configured for ALB also provide the benefit of NIC fault tolerance (NFT).

Option 1. NIC Fault Tolerance (NFT) Configuration

NIC Fault Tolerance provides the safety of an additional backup link between the server and hub

or switch. In the event of hub or switch port, cable, or NIC failure, you can maintain

uninterrupted network performance.

NIC fault tolerance is implemented with a primary NIC and a backup, or secondary NIC. During

normal operation, the backup NIC will have its transmission disabled. If the link to the primary

NIC fails, the link to the secondary NIC automatically takes over.

•Setting Up NIC Fault Tolerance

To use NIC Fault Tolerance (NFT), you must have two or more Compaq Fast Ethernet NC series

NICs installed in your server. The default settings of the team properties are recommended.

Option 2. Adaptive Load Balancing (ALB) Configuration

The ALB (Adaptive Load Balancing) option is recommended for the best performance and

availability of your cluster.

Adaptive Load Balancing (ALB) is a simple and efficient way to increase your server’s

transmission throughput. With ALB, as you add NICs to your server, you can group them in

teams to provide up to 400 mbps with a maximum of four Compaq Fast Ethernet NICs. The ALB

software continuously analyzes transmission loading on each NIC and balances loading as

needed.

•Setting Up Adaptive Load Balancing

To use Adaptive Load Balancing (ALB), you must have two, three, or four Compaq Fast Ethernet

NC series NICs installed in your server, all linked to the same network switch. To configure

ALB, all the NICs in the team must operate at 10/100 Mb/s or 1 Gb/s. The default settings of the

team properties are recommended.

Note: For maximum benefit, ALB should not be used under NetBEUI and some IPX

environments. For a list of specific environments, see the your Administrator Guides.

Supported Ethernet Interconnects for Compaq Parallel Database Clusters using Oracle Parallel Server 10

ECG062/0299

Steps for Configuring NICs Utilizing Teaming

1. Click the Start menu and go to Control Panel under the Settings menu.

2. Double click the Network control panel. Click on the Adapters tab. All of the installed

NICs should be listed. Select a NIC and click on Properties.

Autres manuels pour 1850R - ProLiant - 128 MB RAM

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Compaq Ordinateur de bureau

Compaq

Compaq Presario SR1400 - Desktop PC Manuel utilisateur

Compaq

Compaq Deskpro 386 - Desktop PC Manuel

Compaq

Compaq 8000 - Elite Convertible Minitower PC Manuel de référence

Compaq

Compaq dx1000 - Microtower PC Manuel utilisateur

Compaq

Compaq 6005 - Pro Microtower PC Guide de configuration

Compaq

Compaq Evo D310 Micro-Desktop Manuel du produit

Compaq

Compaq 239158-999 - Mini Tower - Power Supply 250... Mode d’emploi

Compaq

Compaq Presario 6200 - Desktop PC Instructions d'installation

Compaq

Compaq 127507-008 - Deskpro EP - 64 MB RAM Manuel utilisateur

Compaq

Compaq Professional AP500 Manuel

Compaq

Compaq BL10e - HP ProLiant - 512 MB RAM Manuel de référence

Compaq

Compaq Presario SR5700 - Desktop PC Comment utiliser

Compaq

Compaq 112726-001 - ProLiant - 6500 Manuel utilisateur

Compaq

Compaq Deskpro 2000 Manuel utilisateur

Compaq

Compaq dc5750 - Microtower PC Manuel utilisateur

Compaq

Compaq Presario SR1400 - Desktop PC Instructions d'installation

Compaq

Compaq DA-64CAA-DA - AlphaServer - ES40 Model 2 Manuel utilisateur

Compaq

Compaq 179740-001 - ProLiant - 3000 Manuel utilisateur

Compaq

Compaq dc5850 - Microtower PC Manuel utilisateur

Compaq

Compaq Presario 8000 - Desktop PC Manuel utilisateur

Compaq

Compaq SR5450F - Presario - 2 GB RAM Comment utiliser

Compaq

Compaq Presario SG3200 - Desktop PC Comment utiliser

Compaq

Compaq Deskpro 4000N - Desktop PC Manuel utilisateur

Compaq

Compaq Presario SR5000 - Desktop PC Comment utiliser

Manuels Ordinateur de bureau populaires d'autres marques

HP m9060n - Pavilion - Elite Fiche technique

Asus

Asus E210 Series Manuel utilisateur

Dell

Dell Inspiron 600m Manuel utilisateur

Dell

Dell Inspiron 3662 Manuel utilisateur

TotalFlow

TotalFlow uFLO Manuel utilisateur

HP Presario SV7000 - Desktop PC Manuel utilisateur

HP ProDesk 400 G5 Manuel

Logitech

Logitech MK320 Manuel utilisateur

Dell

Dell XPS 730 H2C Manuel utilisateur

Sony

Sony Vaio Series Manuel utilisateur

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuel utilisateur

Alto

Alto MD 250 Manuel utilisateur

Lenovo

Lenovo ThinkCentre Edge 72 Manuel

Lenovo

Lenovo ThinkStation D20 Manuel

Arbor Technology

Arbor Technology FPC-7800 Series Manuel utilisateur

Sony

Sony VAIO VGX-TP1 Series Manuel utilisateur

Asus

Asus Eee Box B204 Manuel utilisateur

Dell

Dell Optiplex 9010 All In One Manuel utilisateur