Comica LinkFlexAD5 Manuel utilisateur
User Manual
Feature-packed Audio Interface
Foreword
Main Features
Thanks for purchasing Comica feature-packed audio interface LinkFlex AD5
Notice
When working with other products which have high sensitivity, it is recommended to adjust the gain of AD5 to the minimum before turning
it on. Users can then adjust the gain step by step to avoid sound peak or audio feedback.
Before connecting/disconnecting the microphone/instrument, please turn o the 48V phantom power/Inst switch to avoid damaging the
devices.
Please read this user manual thoroughly before using the product, and keep it for future reference.
Please do not expose the product to rain or moisture, and avoid having water or other liquids spilled on it.
Please do not use or store the product near any heat sources such as radiators, stoves, or other heat-producing appliances.
This product is a high-precision product, please prevent it form dropping or colliding.
. 48kHz/24bit Audio Recording, Integrated Dual XLR/6.35mm Interfaces
Design
. Support Recording/Streaming Mode Switch and Direct Monitor
. Support 48V Phantom Power Mics and Hi-Z Instruments Input
. Dual USB-C Interfaces for Connecting Two Computers or Mobile Devices
. Multiple I/O Interfaces to Connect Phones, Tablets, and Computers
. Up to 65dB Gain Range for Wider Mic Compatibility
. Class-leading AD/DA Conversion to Deliver the Most Detailed Sound
. Individual Mic Preamps, Guitar Amps, Monitor Volume and Output Gain
Control
. Digital Signal Processing and Three EQ and Reverb Modes for
Unlimited Creativity
. Featured with Loopback for Sampling, Streaming and
Podcasting
. Support One-key Denoise and Mute, Easy to Use
. High-definition LCD Screen for Flexible and Intuitive Operation
. Built-in Rechargeable Lithium Battery, Operating Time Up to 6
Hours
1
Packing List
Main Part:
Accessories:
2 in 1 Audio Cable
X2
User Manual Warranty Card3.5mm TRRS-TRRS Audio Cable
LinkFlex AD5
User Manual
Feature-packedAudio Interface
2
Components Introduction
Top Panel:
1. LCD Screen
To show the device status intuitively. Please refer to the following “Screen
Display” for more information.
2. MIX Knob
To adjust the volume level of output audios; the volume indicators will
change according to the volume level.
3. Volume Indicator
Indicating the volume level of the output audios.
4. Recording/Streaming Mode Switch Button
Short press to switch between Recording mode and Streaming mode.
AD5 outputs stereo audio in recording mode, IN1 stands for the left
channel, and IN2 the right channel; AD5 outputs mono audio in streaming
mode.
5. Mute Touch Button
Touch to turn on/o Mute.
6. Denoise Touch Button
Touch to turn on/switch/turn o denoise. Please switch to denoise 1 mode
when using dynamic mics; Please switch to denoise 2 mode when using
condenser mics.
7. REB/EQ Touch Button
Long press to switch to EQ or Reverb; short press to choose EQ/REB
modes.
①②
④
⑤
⑥
⑦
③
3
Front Panel:
1. Input Port IN1/2
6.35 TRS instruments and XLR micrphones can be connected to AD5
through the input ports IN1/2. In Recording Mode, IN1 stands for the left
channel and IN2 the right channel.
2. Gain Control Knob 1/2
Adjust the preamp gain for input signals at IN1/2 respectively.
3. 48V Phantom Power Switch 1/2
Turn on/o 48V Phantom Power. When you turn this switch on, phantom
power will be supplied to the XLR jack connected to the IN1/2 ports. Please
turn it on when using a phantom powered microphone.
1. When connecting/disconnecting microphones to AD5, please set the
gain of AD5 to the minimum before turning on/o 48V Phantom power
to avoid damaging the devices.
2. When connecting devices not requiring 48V phantom power to IN1/2
port, please make sure to turn o 48V phantom power.
① ②
③ ④ ③ ④ ⑥⑤ ⑦ ⑧
① ②
4
4. Inst Switch 1/2
Turn on/o the input impedance. Please turn the inst switch on when connecting Hi-Z instruments such as an electric guitar/bass to achieve better input eects.
1. It's recommended to set the gain of AD5 to the minimum before turning on/o Inst switch to avoid feedback problems and damage to the devices.
2. When connecting devices not requiring high inpedance to IN1/2 port, please make sure to turn o Inst switch.
3. To protect your speaker system, leave the monitor speakers turned o when turning the Inst switch on/o.
5. 3.5mm Monitoring Port 1
Plug in 3.5mm TRS/TRRS headphones to monitor.
6. Monitoring Mode Switch
Switch monitoring mode. In direct monitoring mono mode, the monitoring audio is mono; In direct monitoring stereo mode, the monitoring audio is stereo (IN1
stands for the left channel and IN2 the right channel); In direct monitoring mode, AD5 will route the audio signals from IN1/2 directly to the monitor outputs and
headphones with zero latency. In input monitoring mode, audio signals from IN1/2 will be routed to the DAW software and then to the monitor outputs and
headphones with mixed audio, which will cause a delay in monitoring.
7. Loopback Switch
Loopback uses the 'virtual' inputs, which have no physical connectors on the audio interface itself but can directly route the digital signal streams back to DAW
software, it can capture all the audio signals from your computer(e.g., the audio signal output from a web browser) to input to the audio interface.
Short press to turn on/of Loopback. When Loopback is on, AD5 will output audio signals both from IN1/2 and USB-C ports; When Loopback is o, AD5 will output
audio signals from IN1/2 ports.
8. Monitoring Volume Control Knob
Adjust the volume level of the monitoring port1/2.
Loopback only aects the audio output of the USB-C port, not the 3.5mm port.
5
Back Panel: 1. Power/Language Switch Button
Long press to turn on/o; short press to switch the language of AD5
between Chinese and English.
2. USB-C Charging Port
Users can charge AD5 through the 2 in 1 cable.
3. USB Port 1/2
To connect phones/computers to input/output audio signals via the 2 in 1
audio cable. Phones/computers can route audio singals to AD5 and AD5
can achieve the digital output of audio signals from both phones/computers
and IN1/2.
4. 3.5mm Port 1/2
To connect phones to input/output audio signals via the 3.5mm
TRRS-TRRS audio cable. Phones can route audio signals to AD5 and AD5
can achieve analog output of the audio signals from phones and IN1/2.
5. 3.5mm Monitoring Port 2
Plug in 3.5mm TRS/TRRS headphones to monitor.
6. Line Output Port
Connect to the monitor speakers, L means the left channel and R the right
channel.
7. Reset Hole
If the device cannot be charged or is unable to function, insert the reset
pin into the reset hole to reset it.
① ② ③ ④ ⑤ ⑥ ⑦
6
Screen Display:
Off Off 1 2
Direct Monitor
Mono
Direct Monitor
Stereo
Input Monitor
Left Channel
Right Channel
Monitoring Audio Dynamic Bar
Normal Working
Muting
Inst 148V Phantom Power 1 Inst 248V Phantom Power 2
（Applicable to the status of other features）
On
O
Input Audio Dynamic Bar
Power Status
7
Installation and Usage
Devices Connection
Users can connect the corresponding devices to the audio interface referring to the following pictures：
8
Table des matières
Manuels Équipement d'enregistrement populaires d'autres marques
Strymon
Strymon NIGHTSKY Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuel utilisateur
Tews Technologies
Tews Technologies TPMC465 Manuel utilisateur
Honeywell
Honeywell Excel 50 Manuel utilisateur
SeaLevel
SeaLevel COMM+8.LPCI Manuel utilisateur
Arturia
Arturia AUDIOFUSE STUDIO Manuel utilisateur
