3.
3.
3.
3. Operation
Operation
Operation
Operation Instructions
Instructions
Instructions
Instructions
-The LINEAR BEAM PIXEL is for beam effect for on-site decoration purpose .
-Don ’ t turn on the fixture if it
’
s been through severe temperature difference like after
transportation because it might damage the light due to the environment changes. So make sure
to operate the fixture until it is in normal temperature .
- This light should be keep away from strong shaking during any transportation or movement.
-Don ’ t pull up the light by only the hea d, or it might cause damages to the mechanical parts.
- Don ’ t expose the fixture in overhea t, moisture or environment with too much dust when installing
it. And don ’ t lay any power cables on the floor. Or it might cause electronic shock to the people.
- Make sure the installation place is in good safety condition before installing the fixture.
-Make sure to put the safety chain and check whether the screws are screwed properly when
installing the fixture.
- Make sure the lens are in good condition. It
’
s recommended to replace the units if there are any
damages or severe scratch.
- Make sure the fixture is operated by qualified personnel who knows the fixture before using.
- Keep the original packages if any second shipment is needed.
- Don ’ t try to change the fixtures without any instruction by the manufacturer or the appointed
repairing agencies.
-It is not in warranty range if there are any malfunctions from not following the user manual to
operate or any illegal operation, like shock short circuit, electronic shock, lamp broke, etc.
4.
4.
4.
4. Mounting
Mounting
Mounting
Mounting and
and
and
and Installation
Installation
Installation
Installation
Cautions:
Cautions:
Cautions:
Cautions: For added protection mount the fixtures in areas outside walking paths, seating areas, or in
areas were the fixture might be reached by
unauthorized person nel .
Before mounting the fixture to any surface, make sure that the installation area can hold a minimum
point load of 10 times the device
’
s weight.
Fixture installation must always be secured with a secondary safety attachment, such as an appropriate
safety cable.
Never stand directly below the device when mounting, removing, or servicing the fixture.
8.DMX
8.DMX
8.DMX
8.DMX Channels
Channels
Channels
Channels
Channel
Channel
Channel
Channel
Function
Function
Function
Function Values
Values
Values
Values Description
Description
Description
Description
MOD1 MOD 2
1 1 Dimmer 0-255 Dimmer 0%...100%
2 2 Shutter
0-009 No Function
010-249 Strobe effect slow to fast
250-255 No Function
3 3 TILT 0-255 T
ILT
m ovement
4 TILT Fine 0-255 Fine control of Tilt movement
5 4 Speed 0-255 M ax to min speed for TILT
6 5 Special
0-019 No Function
020-029 No Function
030-039 No Function
040-079 No Function
080-099 Motor reset
100-119 Internal program 1
120-139 Internal program 2
140-159 Internal program 3
160-179 Internal program 4
180-199 Internal program 5
200-219 Internal program 6
220-239 Internal program 7
240-255 Internal program 8
7 6 Pixel 1 0-255 P ixel 1 saturation control (0-100%)
8 7 Pixel 2 0-255 P ixel 1 saturation control (0-100%)
9 8 Pixel 3 0-255 P ixel 1 saturation control (0-100%)
10 9 Pixel 4 0-255 P ixel 1 saturation control (0-100%)
11 10 Pixel 5 0-255 P ixel 1 saturation control (0-100%)
12 11 Pixel 6 0-255 P ixel 1 saturation control (0-100%)
13 12 Pixel 7 0-255 P ixel 1 saturation control (0-100%)
