Color imagination LEDPAR 915IP Manuel utilisateur

User Manual

KEEP THIS MANUAL FOR FUTURE NEEDS

SI-014

tc100°C

LED 0.2m ta40°C

IP65

LEDPAR

915IP

.01.

If the device has been exposed to temperature changes due to environmental changes,

do not switch it on immediately. The arising condensation could damage the device.

Leave the device switched off until it has reached room temperature.

This device falls under protection-class I. Therefore it is essential that the device be

earthed.

The electric connection must carry out by qualified person.

The device shall only be used with rate voltage and frequency.

Make sure that the available voltage is not higher than stated at the end of this manual.

Make sure the power cord is never crimped or damaged by sharp edges. If this would

be the case, replacement of the cable must be done by an authorized dealer.

Always disconnect from the mains, when the device is not in use or before cleaning it.

Only handle the power cord by the plug. Never pull out the plug by tugging the power

cord.

During initial start-up some smoke or smell may arise. This is a normal process and

does not necessarily mean that the device is defective, it should decrease gradually.

Please don't project the beam onto combustible substances.

Fixtures cannot be installed on combustible substances, keep more than 50cm

distance with wall for smooth air flow, so there should be no shelter for fans and

ventilation for heat radiation.

If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively

replaced by the manufacturer or his service agent or a similar qualified person in order

to avoid a hazard.

This device has left the factory in perfect condition. In order to maintain this

condition and to ensure a safe operation, it is absolutely necessary for the user to

follow the safety instructions and warning notes written in this user manual.

CAU T I O N

Becareful with your operations.With a dangerous voltage you cansuffer a

dangerous electric shock when touching wires!

IMPORTANT

Damages caused by the disregard of this user manual are not subject to warranty.

The dealer will not accept liability for any resulting defects or problems.

SAFETY INSTRUCTIONS

Thank you for choosing our LEDPAR 915IP . For your own safety,

please read this manual before installing the device. This manual covers the

important information on installation and applications. Please install and operate

the fixture with following instructions. Meanwhile, please keep this manual well for

future needs.

LEDPAR 915IP is made of a new type of high temperature

strength of cast aluminum casing with nice outlook. The fixture is designed and

manufactured strictly following CE standards, complying with international standard

DMX512 protocol. It’s available independently controlled and linkable with each

other for operation. And it is applicable for large-scale live performances, theater,

studio, nightclubs and discos.

The LEDPAR 915IP adopts 9PCS 15W 5-IN-1 LEDs (RGBAW) which features high

brightness and stability. Please carefully unpack it when you receive the fixture and

check whether it is damaged during the transportation. And please check whether

the following items are included inside the box:

Color Imagination’s

.02.

①

③

UNPACKING

LEDPAR 915IP

Power Cable

Signal Cable

Safety Cable

User Manual

1PC

①

②

③

④

⑤

Euro Standard

UK Standard

USA Standard

OPTIONAL

②

③

⑤

Specifications

Input Voltage:

LED Quantities:

Control Signal:

Control Channel:

Power Consumption:

Dimensions:

Packing Dimensions:

Net Weight:

Gross Weight:

Features

FEATURES & SPECIFICATIONS

• 9PCS 15W 5-IN-1 LEDs (RGBAW)

• 50,000 hours life span and low power consumption

• 25° projection beam angle

• Aluminum die-casting structure design with optimum cooling system

• Infinite RGBAW color mixing system and rainbow effect

• 16.7million additive RGBAW colors whit full saturation control

• 5/7/8 DMX channels

• DMX512, Master-Slave, Sound Activated and auto operation

• Built-in programs that could be called up via a DMX controller

• High speed LED strobe effect and pulse strobe effect

• 0-100% electronic dimming and blackout for all LEDs

• LED display

• IP rated power IN/OUT

• IP rated 3-pin XLR connectors IN/OUT

• IP65 protection rating

• Overheat protection

• -20°-40°C environment temperature

• TO.8A fuse

• Dual mounting brackets for ground or hanging application

AC90-260V 50/60Hz

9PCS 15W 5-IN-1 LEDs (RGBAW)

DMX512, master-slave and sound activated or auto operation

5/7/8 DMX channels USITT DMX-512

145W

285(D)*235(W)*300(H)mm

315(D)*265(W)*330(H)mm

4kg

4.8kg

.03.

.04.

PHOTOMETRIC DATA

300

235

285

25°Beam Angle LUX 0.0929=FC×

Photometric Beam Angle Data

134/1442

471/5074

67/717

134/1443

488/5249

954/10272

1m (3.3ft) 3m (9.8ft) 5m (16.4ft)0m (0ft)

FC/(LUX)

RGBWA

7m (23.0ft)

25°

23/250

89/954

11/125

26/279

76/819

188/2020

9/100

35/382

4/48

10/105

30/323

78/842

5/53

18/198

2/25

5/55

15/171

39/423

.05.

Cautions: For added protection mount the fixtures in areas outside walking paths,

seating areas, or in areas were the fixture might be reached by unauthorized personnel.

Before mounting the fixture to any surface, make sure that the installation area can

hold a minimum point load of 10 times the device’s weight.

Fixture installation must always be secured with a secondary safety attachment, such

as an appropriate safety cable.

Never stand directly below the device when mounting, removing, or servicing the fixture.

· The LEDPAR 915IP is an LED wash light for on-site decoration purpose.

· Don’t turn on the fixture if it’s been through severe temperature difference like

after transportation because it might damage the light due to the environment

changes. So make sure to operate the fixture until it is in normal temperature.

· This light should be keep away from strong shaking during any transportation or

movement.

· Don’t pull up the light by only the head, or it might cause damages to the

mechanical parts.

· Don’t expose the fixture in overheat, moisture or environment with too much dust

when installing it. And don’t lay any power cables on the floor. Or it might cause

electronic shock to the people.

· Make sure the installation place is in good safety condition before installing the

fixture.

· Make sure to put the safety chain and check whether the screws are screwed

properly when installing the fixture.

· Make sure the lens are in good condition. It’s recommended to replace the units if

there are any damages or severe scratch.

· Make sure the fixture is operated by qualified personnel who knows the fixture

before using.

· Keep the original packages if any second shipment is needed.

· Don’t try to change the fixtures without any instruction by the manufacturer or

the appointed repairing agencies.

· It is not in warranty range if there are any malfunctions from not following the

user manual to operate or any illegal operation, like shock short circuit, electronic

shock, lamp broke, etc.

OPERATION INSTRUCTIONS

INSTALLATIONS

.06.

Truss installing

Satety Clamp Safety Cable

from a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture

is kept at least 0.5m (1.5 ft) away from any flammable materials (decoration etc.).

Always use and install the supplied safety cable as a safety measure to prevent

accidental damage and/or injury in the event the clamp fails.

Mounting points: Overhead mounting requires extensive experience, including

amongst others calculating working load limits, a fine knowledge of the installation

material being used, and periodic safety inspection of all installation material and the

fixture. If you lack these qualifications, do not attempt the installation yourself.

Improper installation can result in bodily injury.

Be sure to complete all rigging and installation procedures before connecting the

main power cord to the appropriate wall outlet.

Clamp Mounting: The LEDPAR 915IP provides a unique mounting bracket assembly,

and the safety cable rigging point in one unit (see the illustration below). When

mounting this fixture to truss be sure to secure an appropriately rated clamp to the

handle using a M10 screw fitted through the center hole of the handle. As an added

safety measure be sure to attached at least one properly rated safety cable to the

fixture using on of the safety cable rigging point.

Floor projection Water proof

Regardless of the rigging option you choose for your , always be sure

to secure your fixture with a safety cable. The fixture provides a built-in rigging point

for a safety cable on the hanging bracket as illustrated above. Be sure to only use the

designated rigging point for the safety cable and never secure a safety cable to a

carrying handle.

LEDPAR 915IP

Connect the provided XLR cable to the female 3-pin XLR output of your controller and

the other side to the male 3-pin XLR input of the par can. You can chain multiplePar

can together through serial linking. The cable needed should be two core, screened

cable with XLR input and output connectors. Please refer to the diagram below.

DMX-512 connection with DMX terminator

DMX-512 CONTROL CONNECTIONS

POWER IN

DMX IN

POWER OUT

LED Display

UP DOWN

ENTER

DMX IN DMX OUT

POWER IN

.07.

DMX Output

3-Pin XLR Socket

DMX Input

3-Pin XLR Socket

1:Ground

2:Data(-)

3:Data(+)

1 2

COMMON

DMX+

DMX-

DMX512 IN

3-PIN XLR

DMX512 OUT

3-PIN XLR

2 1

For installations where the DMX cable has to run a long

distance or is in an electrically noisy environment, such as

in a discotheque, it is recommended to use a DMX

terminator. This helps in preventing corruption of the

digital control signal by electrical noise. The DMX

terminator is simply an XLR plug with a 120 Ω resistor

connected between pins 2 and 3,which is then plugged

into the output XLR socket of the last fixture in the chain.

Please see illustrations below.

120 Ω

MENU OPERATIONS

Address setting

Channel mode

Slave mode

Sound mode

Jump mode

Strobe mode

Fade mode

Auto mode

Static color

Strobe mode

Red dimmer

Green dimmer

Blue dimmer

White dimmer

Amber dimmer

Display normal

Inversion

C H N D 5 c

S L A U

S 0 U M

C 0 L 0 C 0 0 0 C 2 5 5

7 C

F A D E F A 0 1 F A 1 5

J U M P J U 0 1 J U 2 0

A U T 0

M A N U R E R 0 0 0 R 2 5 5

M 0

yES

D I S P

G R E E

B L U E

B 0 0 0 B 2 5 5

G 0 0 0 G 2 5 5

m 0 y E S

8 c

S D 1 S D 8

f l 0 f l 4

f l 0 f l 50 1

u R E E

y L U E y 0 0 0 y 2 5 5

u 0 0 0 u 2 5 5

.08.

PIN3

PIN2

DMX CHANNELS

.09.

0-100% Red Dimmer

0-100% Green Dimmer

0-100% Blue Dimmer

0-100% White Dimmer

0-100% Amber Dimmer

DescriptionChannel Function Value

0-255

Red

Green

Blue

White

Amber

5CH Mode

0-100% Linear dimmer for section 1

0-100% Linear dimmer for section 2

0-100% Linear dimmer for section 3

0-100% Linear dimmer for section 4

0-100% Linear master dimmer

Dimmer mode

Strobe effect from slow to fast

No function

Pulse strobe effect from slow to fast

No function

Gradual fading strobe effect from dark to bright

No function

Gradual fading strobe effect from bright to dark

0-100% Linear master dimmer

DescriptionChannel Function Value

0-255

0-006

007-065

066-069

070-128

129-132

133-191

192-195

196-255

0-255

Red

Green

Blue

White

Amber

Strobe

Dimmer

7CH Mode

0-100% Linear dimmer for section 1

0-100% Linear dimmer for section 2

0-100% Linear dimmer for section 3

0-100% Linear dimmer for section 4

0-100% Linear master dimmer

Dimmer mode

Strobe effect from slow to fast

No function

Pulse strobe effect from slow to fast

No function

Gradual fading strobe effect from dark to bright

No function

Gradual fading strobe effect from bright to dark

DescriptionChannel Function Value

0-255

0-006

007-065

066-069

070-128

129-132

133-191

192-195

196-255

Red

Green

Blue

White

Amber

Dimmer

Mode

/Strobe

Mode

CH8

(0-59)

8CH Mode

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Color imagination Matériel de DJ

Color imagination

Color imagination MINISPOT 50 SI-098 Manuel utilisateur

Color imagination

Color imagination LED-PAR36X3W-RGB SI-018D Manuel utilisateur

Color imagination

Color imagination LEDPAR 64 Manuel utilisateur

Color imagination

Color imagination SI-027 Manuel utilisateur

Color imagination

Color imagination SI-166 Manuel utilisateur

Color imagination

Color imagination LEDPAR 36AS 7*10W 4IN1 SI-016 Manuel utilisateur

Color imagination

Color imagination SI-045 Manuel utilisateur

Color imagination

Color imagination SI-018R Manuel utilisateur

Color imagination

Color imagination LEDARC 543 Manuel utilisateur

Color imagination

Color imagination SI-018L Manuel utilisateur

Manuels Matériel de DJ populaires d'autres marques

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuel du propriétaire

Chauvet

Chauvet OVATION E-930VW Manuel utilisateur

Zumtobel

Zumtobel APHRODITE Home Manuel utilisateur

Snow Masters

Snow Masters Zig Oscillator Manuel utilisateur

EuroLite

EuroLite 50530554 Manuel utilisateur

Beamz

Beamz BUV243 Manuel utilisateur

thomann

thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur

Eagletone

Eagletone 6 Eyes Flower Manuel utilisateur

EuroLite

EuroLite FLD-1508 Manuel utilisateur

Technical Pro

Technical Pro LG8xSEA Manuel utilisateur

JB Systems

JB Systems Lounge Laser DMX Manuel utilisateur

Lightmaxx

Lightmaxx Vega Halo 90 Manuel utilisateur

Elation

Elation FUZE WASH Z350 Manuel utilisateur

Maverick

Maverick MK3 WASH Manuel utilisateur

Infinity

Infinity TF-260C7 Fresnel Manuel utilisateur

Chauvet

Chauvet EVE E-50Z Manuel utilisateur

Eliminator Lighting

Eliminator Lighting E 138 Manuel utilisateur

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur