Code CR7000 Series Manuel utilisateur

MANUAL VERSION 1.0

RELEASE DATE: MARCH 2019

iPhone® is a registered trademark of Apple Inc.

Dragontrail™is a trademark of Asahi Glass, Limited.

Note from the Code Team

Thank you for purchasing the CR7018! Healthcare’s first purpose-built battery backup case is here.

Approved by infection control specialists, the CR7018 is fully enclosed and built with CodeShield®

plastics, known to withstand the harshest chemicals used in the industry. Made to protect and

extend the battery life of Apple’s iPhone®7 and 8, the CR7018 will keep your investment safe and

clinicians on the go. The DragonTrail™ glass screen provides another layer of quality for the highest

level of protection on the market. Easily swappable batteries keep your case running as long as you

are. Don’t wait for your device to charge again—unless that’s how you prefer to use it, of course.

Made for enterprises, the CR7018 product ecosystem provides a durable, protective case, flexible

charging methods, and a battery management solution so you can focus on what matters.

We hope you enjoy your enterprise mobility experience. Have any feedback? We’d love to hear from

you.

Your Code Product Team

product.strategy@codecorp.com

Table of Contents

Case and Accessories ............................................................................................................. 3

Product Kits ...................................................................................................................................3

Battery Charging Kits......................................................................................................................3

Cables............................................................................................................................................3

Accessories ....................................................................................................................................3

Services .........................................................................................................................................3

Product Assembly .................................................................................................................. 4

Unpacking and Installation .............................................................................................................4

Inserting iPhone ...................................................................................................................................................4

Inserting/Removing Batteries..............................................................................................................................7

Charger Assembly and Mounting ........................................................................................................................8

Battery Charging and Best Practices ..................................................................................................................12

Maintenance and Troubleshooting ...................................................................................... 13

Approved Disinfectants ................................................................................................................13

Routine Cleaning and Disinfection ................................................................................................13

Troubleshooting...........................................................................................................................13

Contact Code for Support .............................................................................................................14

Warranty ............................................................................................................................ 14

Legal Disclaimer .................................................................................................................. 14

Statement of Agency Compliance ........................................................................................ 15

Case and Accessories

The following tables summarize the parts included within the CR7018 product line. More product

details can be found on Code’s website.

Product Kits

Part Number Description

iPhone 7

CR7018-PKXXX-7 CR7018 (iPhone 7 Case, Light Gray, Palm), Battery

CR7018-PKXXU-7 CR7018 (iPhone 7 Case, Light Gray, Palm), Battery, 3-ft. Straight USB Cable

CR7018-PKX2X-7 CR7018 (iPhone 7 Case, Light Gray, Palm), Battery, Spare Battery

iPhone 8

CR7018-PKXXX-8 CR7018 (iPhone 8 Case, Light Gray, Palm), Battery

CR7018-PKXXU-8 CR7018 (iPhone 8 Case, Light Gray, Palm), Battery, 3-ft. Straight USB Cable

CR7018-PKX2X-8 CR7018 (iPhone 8 Case, Light Gray, Palm), Battery, Spare Battery

Battery Charging Kits

Part Number Description

CRA-A172 CR7018 5-Bay Charging Station and 3.3 Amp US Power Supply

CRA-A175 CR7018 10-Bay Charging Station and 3.3 Amp US Power Supply

CRA-A176 Code Reader Accessory for CR7018 - Charger Upgrade Package (Split

Cable Adapter, 5-Bay Battery Charging Station)

Cables

Part Number Description

CRA-C34 Straight cable for CR7018, USB to Micro USB, 3 ft (1 m)

CRA-C70 Split Cable Adapter

Accessories

Part Number Description

CRA-B718 CR7018 Battery

CRA-VM718 Vertical Mount Base for CRA-A172 and CRA-A175 Charging Stations

CRA-P71 3.3 Amp US Power Supply

CRA-P4 US Power Supply - 1 Amp USB Wall Adapter

Services

Part Number Description

SP-CR718-E107 Accessory for CR7018 - Replacement Top Plate for iPhone 7, 1 count

SP-CR718-E1074 Accessory for CR7018 - Replacement Top Plates for iPhone 7, 4 count

SP-CR718-E108 Accessory for CR7018 - Replacement Top Plate for iPhone 8, 1 count

SP-CR718-E1084 Accessory for CR7018 - Replacement Top Plates for iPhone 8, 4 count

*Other CR7018 service and warranty options can be found on Code’s website

Product Assembly

Unpacking and Installation

Read the following information before unpacking or assembling the CR7018 and its accessories.

Inserting iPhone

The CR7018 houses Apple’s iPhone 7 and 8 models. Please note that the top plate will vary

depending on the iPhone model.

The CR7018 case will arrive with the top and bottom carriage connected. With a thumb on

the right and left side of the speaker opening, push up approximately 5 millimeters to clear

the lightning connector.

iPhone 7 top plate

with fitted insert

iPhone 8 top plate

Pull the top plate toward you, away from the bottom carriage. Do NOT try to slide it all the

way up.

Before inserting the iPhone, thoroughly clean the iPhone screen and both sides of the glass

screen protector. Screen responsiveness will be hindered if the screens are dirty.

Insert the iPhone into the top plate; it will click into place.

Replace the top plate into the bottom carriage directly above the lightning connector, similar

to the removal process; the top plate will be inserted approximately 5 millimeters from the

edge of the bottom carriage. Push down on the top plate to secure the iPhone onto the

lightning connector and seal the case.

Do NOT try to slide it down from the top.

Your CR7018 case will come with two screws and a 1.3 mm hex key. For larger deployments,

it is recommended to procure a specialized tool

for quick assembly.

Insert the screws to secure phone and case.

The following URLs will direct you to

recommended tools for installing the provided

screws.

•Ultra-Grip Screwdriver

ohttps://www.mcmaster.com/7400A27

•8 Piece Hex Screwdriver Set

ohttps://www.mcmaster.com/57585A61

Inserting/Removing Batteries

Only Code’s CRA-B718 batteries are compatible with the CR7018 case. Insert a B718

battery into the cavity; it will click into place.

The fuel gauge LEDs will light up, indicating the battery’s state of charge. If the LEDs do not

light up, fully charge the battery before using.

To verify the battery is properly connected, a lightning bolt will be

located on iPhone’s battery, signifying a charge status and successful

battery installation. To remove the battery, push both battery

compartment latches inward until the battery pops out. Pull the battery

from the cavity.

Charger Assembly and Mounting

The CR7018 chargers are designed to charge the B718 batteries. Customers can purchase

5 or 10-bay chargers. Two 5-bay chargers are mechanically interlinked to create the 10-bay

charger. 5 and 10-bay chargers use the same power supply (CRA-P71), but have different

cables: the 5-bay charger has a single, linear cable where the 10-bay charger requires a

two-way splitter cable. Charging stations can be mounted on a vertical mount accessory or to

the wall, which can be seen in the sections below.

Note: Use only cables supplied by Code to ensure proper communication and adequate

charge rates. Only Code cables are guaranteed to work. Damage caused using third-party

cables will not be covered under warranty.

5-Bay Charger Installation

The 5-bay charging station will hold and charge 5 batteries from zero to full charge within 3

hours. The CRA-A172 charger kit comes with a 5-bay charger, cable and power supply.

Insert the cable into the female port on the bottom-side of the charger. Route the cable

through the grooves and connect it to the power supply.

LED charge indicators reside on both sides of each battery bay to quickly check the charge

status from any angle.

Note: There is a delay of up to thirty minutes between the battery gauge indicating it’s fully

charged and the charger LEDs switching from blinking to solid. LED indicator definitions are

presented in the “Inserting Batteries into the Charger”section.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Code Lecteur de codes-barres

Code

Code Reader 1200 Manuel d'installation et d'exploitation

Code

Code CR1200 Manuel utilisateur

Code

Code CR3 Manuel utilisateur

Code

Code CR1400 Manuel utilisateur

Code

Code CORTEXJPOS CR2300 Guide de configuration rapide

Code

Code CR7010 Series Manuel utilisateur

Code

Code CR2 Manuel utilisateur

Code

Code CR3 Manuel utilisateur

Code

Code CR1500 Mode d'emploi

Code

Code CORTEXJPOS CR2300 Manuel utilisateur

Code

Code Code Reader 822 Series Guide de configuration rapide

Code

Code CORTEXJPOS CR6000 Manuel utilisateur

Code

Code CORTEXJPOS CR5000 Manuel utilisateur

Code

Code CR1500 Manuel utilisateur

Code

Code CORTEXJPOS CR5000 Manuel utilisateur

Code

Code CR4405 Manuel utilisateur

Code

Code CR2 Manuel utilisateur

Code

Code CR1400 Manuel utilisateur

Code

Code CR1500 Manuel utilisateur

Code

Code CR1400 Manuel utilisateur

Code

Code CR4400 Manuel de l'opérateur

Code

Code CR900FD Manuel utilisateur

Code

Code CR4405 Manuel utilisateur

Code

Code 900FD Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur