Code Alarm F60 Manuel utilisateur

F60lF65

Remote Vehicle Control System

Car

Start,

Security

and

Convenience

System

IMPORTANT NOTE: The operation

the F60/F65

described in this

manual

is applicable

most

vehicles. However,

due

to the engine type

and

configuration

some

vehicles

(Le.

diesel

engines),

some functions

AND/OR SAFETY PRECAUTIONS

may

not

apply.

Please see your

installing

dealer

for more information.

101101-4

9/01

101101-4

FSD-5S.p6S

9/13101,12:14

2 Table

Contents

Features and Benefits

the

F60/F65 ..................................... 4

UsingYour RemoteTransmitter .............................................. 5

Arming the Security System

Pre-arm Mode

Disarming the Security System

Attempted Intrusion Identification

Disabling

the

IT_sTM

InteriorTheft

Sensor ............................... 6

Two-Stage Door Unlock

Activating the Trunk Release Feature

Turning

the Vehicle Headlights

Using the Car Finder Feature

Personal Protection Alarm (Panic)

Remote StartI Stop Feature

Using Valet Mode

UsingYour Remote Starter ......................................................7

Starting

Your

Vehicle

your

vehicle stalls

does

not

start

Remote Start Safety Features

Entering the Vehicle While it is Running via Remote Start

Pre-Heating or Pre-Cooling the Interior of the Vehicle

Using the "Quick-stop" Feature

Automatic

Convenience

Options

............................................ 7

When Your Security System

Triggered ...............................8

The InteriorStatus

Indicator

.................................................... 8

System Maintenance................................................................ 9

Changing the Remote Control Battery

Adding Remote Controls to Your System

Deleting

Lost

Stolen

Remote Controls

from

Your

System

BasicTroubleshooting ............................................................ 10

Emergency Disarm Procedure ..........................................

Emergency Disarm Button Location

System Layout ........................................................................ 12

Programming Selectable

Options

......................................... 13

Code Alarm Warranty Plan.....................................................

Code AlarmTheft Protection Plan ......................................... 18

1011014

F60-6S.p65 2 9/13fOl, 12:14

Features

and

Benefits

the F60lF65

'"J

Two

Easy-to-Use Weather-Resistant Remote Controls

The remote controls included with the F60/F65 utilize durable,

moisture resistant cases and sealed rubber buttons for reliability

and long life. Rolling code technology prevents the transmitter signals

from being duplicated. The button functions are clearly labeled to make

the F60/F65 simple to operate.

All

Entrances Protected

Opening any door or entrance protected

the security system

triggers the vehicle's horn and flashes the vehicle parking lights.

''R

Starter Disable

The F60/F65 protects your vehicle from theft by disabling the starter

when the system is armed.

?sllT-sTM

InteriorTheft Sensor

This patented sensor uses infra-red technology to reliably detect

vehicle impact associated with attempted intrusion. The

IT·sTM

sensor guards against vehicle body damage, and theft of the

vehicle's eqUipment (such as airbags) and personal belongings.

,}] Remote Keyless Entry

The F60/F65 conveniently locks and unlocks vehicle doors and

opens the trunk or hatch by remote

control"

ii1!

Personal Protection Features

Remote Panic Alarm, Illuminated Entry, and Car Finder are among

array of features that enhance personal safety"-

':41

InteriorStatus Indicator

The bright-red warning light is

effective visual deterrent to a

WOUld-be

thief.

lJ~

Remote Start

The F60/F65 allows you to warm

your vehicle

and preheat

pre-cool the interior with the press of a button

the remote control.

~ PowerRange™ Antenna

This long-range antenna allows you to operate the F60/F65 from

distances of up to

'I,

mile.

---

Remote-start your vehicle from the

safety of your home, apartment or office building.

• IIvehicle

equipped

with

power

door

locks

and

they

are

connected

the

aiarmsystem

your

installer.

May

require

additional

connections,

components,

andfer

charges.

See

your

installerfordetails

•••

Range

results

may

vary

due

atmospheric

conditions

and/or

the

presence

strong

radio

frequency

signals.

Specifications

may

change

without

prior

notice.

101101·4

F60-6S.p6S

9/13/01,12:14

4 Using Your Remote Transmitter

Press to ARM

the·

Security System and

Lock the Doors

Press for Car Finder

Press and Hold for

Panic Alarm

Arming

the SecuritySystem

Press

DISARM

sIlCtliity

System

and

Unlock

Doors

Press

lWlCE

for

Two-Stage

Door

Unlock*

Press

and

HoldtoOpenTrunk

Press START to start

the vehicle

arm the system, exit the vehicle, close all doors, then

press'

the

ARM button. The horn will "chirp" twice' and the parking lights will

flash twice, indicating the system is armed. The doors will also lock at

this time (if equipped and connected). The status indicator (red

warning light on the dash) will blink steadily, once per second.

Pre-arm Mode

If the horn chirps and the parking lights flash only once, this indicates

that the vehicle courtesy light is on, or that an entrance is not closed

securely. Check to see that doors, hood, and trunk are properly

closed. Once all entrances are secured (and the courtesy light

off),

the system will chirp I flash again.The system is now fully armed.

(If the entrance is not secured within 4 minutes, the system will arm

and ignore the unsecured entrance until it is closed.)

Disarming the Security System

disarm the system, press the DISARM button. The horn will chirp

and the parking lights will flash once, and the doors will unlock.

The courtesy light will turn

for 1 minute, or until the vehicle is started.

Attempted

IntrusionIdentification

If the horn chirps four times when disarming, this indicates that the

system was triggered in your absence. The status indicator will also

flash

rapidly.

Perform the following operation to determine the protected

zone that triggered the system:

After disarming, press the

emergency override button.

The horn will chirp to indicate

the cause of the alarm trigger:

• Throughoulthismanual, 'press' refersto pressing

chirp

JT~STM

Interior Theft Sensor

chirps

Door

,3,

;chirps

Hood

chirps

Trunk/Optional Sensors

5 chirps Ignition was turned on

forless

than

1second; 'press and hold'refers to pressing formore than t second.

I If

you

have

chosen

the

Silent

Arming

Option,

the

hom

will

not

sound

when

arrninQ

disarming

untilthe

appropriate

bullen

pressed

U$OCond time. .

101101·4 FSQ-S5.p65 4 9/13101. 12:14 PM

Using Your Remote Transmitter (cant.)

Disabling

the

IT-sTM

Interior

Theft

Sensor

It may be necessary at times to disable the

IT_sTM

InteriorTheft Sensor,

especially when parking

areas (like parking garages) where

extreme vibration may cause false alarms. Press

the

ARM

button

and

then press the FIND/PANIC

button

within two seconds

pressing

ARM to disable the interior theft sensor. The horn will chirp three times

to indicate that the sensor is disabled. The sensor will become

enabled again the next time the system is armed normally.

Two-Stage

Door

Unlock

If this feature is enabled

your system, pressing DISARM one time

will unlock only the driver's door. Press DISARM again within 1 minute

to unlock all doors.

Activating

theTrunkReleaseFeature

Press and hold TRUNK to open the vehicle trunk or hatch (if equipped

and connected). If this button is used to operate another accessory,

the accessory will stay active for as long as the button is held.

Usingthe

Car

Finder

Feature

Press FIND

the remote control to locate your vehicle. The horn will

emit five short chirps.

PersonalProtection

Alarm

(Panic)

Press and hold the PANIC button to activate the vehicle horn and

parking lights for 30 seconds. (If the vehicle horn is connected, the

horn will "pulse" for 30 seconds.) Press any remote control button to

turn off the Panic alarm.

Remote

Start/Stop

Feature

Press and hold· the START button

the remote control. If

all

safety

parameters are correct, the engine will start within 5 seconds (diesel

engines will take longer.) Press and hold· the START button again to

turn the vehicle off. (Turn to page 6 for more

remote start features.)

101101-4 FS0-6S.p65 5 9/13101,12:14 PM

6 Using Your Remote Transmitter

(cont.)

Using

Valet

Mode

If the Passive Arming feature is enabled

your system, Valet mode

temporarily prevents the alarm system from arming automatically.

This is useful when fueling

servicing your vehicle.

enter

Valet

Mode:

With the vehicle ignition on, press the ARM button. The red dashboard

warning light (status indicator) will turn

for one second, then turn

off. This indicates that the system is

Valet mode. Once the ignition is

turned off, the status indicator will emit a quick double-flash pattern.

Note:

Valet mode, all keyless entry, convenience and remote start

features operate normally.

exit

Valet

Mode:

With the vehicle ignition on, press the DISARM button. The red

dashboard warning light (status indicator) will turn on for one second,

then turn off. This indicates that the system has exited Valet mode.

Hint:

prevent your security system from automatically arming while

unloading or refueling your vehicle, without placing the system in

Valet mode, simply press the disarm button

your remote control

transmitter after turning the ignition key off. Doing so places your

system into a temporary or onetime Valet mode. Next time you exit

your vehicle the system will arm in the normal manner.

Using Your Remote Starter

Starting

Your

Vehicle

The remote start function is activated by pressing and holding the

START button on the remote control. The system will check the vehicle

to ensure that it is safe to start, and if all safety parameters are correct,

the engine will start within 5 seconds (diesel engines will take longer.)

Press and hold START again to turn the vehicle off.

yourvehicle stalls

does

not

start...

If the vehicle stalls or does not start, the F60/F65 will pause 5

seconds, then try 3 more times to start the vehicle (a total of four

attempts). The system pauses 5 seconds between each start attempt. If

the vehicle does not start after the fourth attempt, the F60/F65 will

abort the start process.

Your vehicle can be started by remote control whether the alarm is

armed or disarmed. When the alarm is armed, the impact sensor turns

off when the vehicle is started

prevent the engine vibration from

setting off the alarm.

101101-4 F6Q-6S.p65 6

9/13'01,12:14

Using

Your

Remote

Starter

(cont'd)

RemoteStartSafetyFeatures

For safety and security reasons, the F60lF65 will shut off the vehicle

during remote start if any of the following occur:

• The vehicle hood is opened

• The brake is pressed before the vehicle ignition is turned

with the key

• The engine reaches 3 times its normal idle'

• The alarm is triggered

As a safety precaution, the vehicle will shut off if left unattended for 12

or 25 minutes, depending

the time preset by your installer.

Entering the Vehicle While It

Running via Remote

Start

Press DISARM to unlock the door(s) and turn off the alarm

system (if it is not already off).

Enter the vehicle.

not press the brake pedal.

Insert the key into the ignition and turn to the ON position.

Press the brake pedal. The remote starter disengages and the

vehicle will operate normally.

Pre-Heating

Pre-Cooling the Interior

the Vehicle

Before exiting the vehicle, set the temperature controls to the desired

setting and operation. After the

F601F6~

starts the vehicle, the heater

air-conditioning

will

activate

and

heat

cool

the

interior

your

setting.

Using the "Quick-stop"Feature

If you want to make a short stop and leave your vehicle running (to

keep

the interior warm

cool, for instance), the quick stop feature allows

you to do this while keeping your vehicle secure and your keys with you.

engage quick stop:

While vehicle is running, place the transmission

PARK.

With your foot off the brake pedal, press and hold the START

button

the remote control. The parking lights will turn

on,

indicating that the vehicle is now running via remote start.

Remove the keys from the ignition and exit the vehicle. Press

ARM to arm the alarm system if desired.

Nole:

Do not leave children or animals unattended

the vehicle

when using the quick stop feature.

•

The

tach

wire

must

connected

and

the

system

must

tach

monitor

mode.

101101·4

F6()"65.p65

7 9113101,12:14 PM

8 Automatic Convenience Options

The F60/F65 performs a variety

automatic functions to enhance

security and comfort. Some of these features are programmable at the

time

installation. Please see your installer

for

further details.

IlluminatedEntry

When the alarm system is disanmed, the vehicle courtesy lights will tum

on for 1 minute, or until the vehicle is started or the system is re-armed.

AutomaticArming

The

F60/F65 will arm automatically 1 minute after the ignition is

turned off. This feature can be temporarily disabled

placing the

system into Valet mode.

Ignition Lock

If all doors are closed and the vehicle is started with the

key,

the doors

will automatically lock.

Ignition Unlock

The doors will automatically unlock after the ignition is turned

off.

When Your Security System

Triggered

The F60/F65 will trigger if one

the following events occurs while the

system is armed:

• Any protected entrance is opened

• The vehicle ignition is turned on

• The vehicle is jolted hard enough to signal the impact detector

Once the alarm is triggered, the hom (or horn) sounds and the vehicle

parking lights flash for 30 seconds. The system will then

re-anm,

awaning

the

next intrusion attempt.

stop the horn while keeping the alarm armed

and

doors locked, press the ARM button while the system is triggered.

The

Interior Status Indicator

The Status Indicator is a high-intensity red light mounted in a visible

location

the vehicle dashboard. This red light gives a visual indication

of the alarm system's state

operation. Note the chart below:

the

Status Indicator is... ....then

the

Security System

Oft

Flashing Slowly

Flashing Very Quickly

Flashing Intermittently

(2,

,flashes, off, 2 flashes)

" " .

On (not flashing)

101101-4 F6()'65.p65 •

is disarmed

armed

was triggered in your absence

(see Attempted Intrusion ID -page

is in Valet mode

Pre-arm mode

9/13101,12:14

~~~~~M~a~in~t~e~n~a~n~c;e~~~~~~~~~~~~~'9

Changingthe Remote ControlBattery

The 12-voltalkaline battery supplied in yourremote

transmitter should last approximately one year,

depending

usage. When the battery begins to

weaken, you will notice a decrease

range, or

the distance from your vehicle that your remote

transmitter will operate. Follow the instructions

below to change the remote transmitter battery.

Open

Back

Remote

TlP,:psmitter

1. Using a coin pry off the back of the transmitter Itne

transmitter snaps together} and expose the battery.

Remove the old battery and replace with GP-23A or

equivalent.

sure to observe the

(+)

and

(-)

signs

the battery

compartment.

Replace the case backing, then test the remote transmitter.

It is not necessary to re-program the remote transmitter after

changing the battery.

AddingRemote Controls toYour System

The F60/F65 has the ability to operate from

to eight

(S)

remote

controls. Follow these instructions to add a remote control to your

system.

Make sure the system

disarmed and the ignition is off.

Open the driver'S door.

Turn vehicle ignition on.

Press and hold emergency override button.

After 15seconds, the horn will sound three (3) times. This

indicates that the unit has entered the remote control

programming mode.

Release the button.

Press the ARM button (button

on the remote control to be

programmed.

The horn will sound once, indicating that the system has

"learned" that remote control.

Repeat step 6 for any additional remote controls.

Turn the vehicle ignition off to exit the programming mode.

Test

all remote controls to ensure that they work properly.

101101-4

F6Q-65.p65

9 9113101,12:14 PM

System Maintenance (cant.)

Deleting

Lost

Stolen Remote

Controls

from

Your System

If one

your remote controls is lost or stolen, follow these instructions

IMMEDIATELY to remove the control code from your system.

Have all remaining remote controls available.

Enter the control programming mode by following steps 1 - 5

Adding

Remote Controls

Your

System

(page 8).

3a.

you

have

only

one

remaining

remote

control,

pressthe

ARM button on that remote control

eight

(8)

times,

pausing

at least 1 second between each press. Make sure that the

horn chirps each time you press the ARM button.

3b.

you

have

two

remaining

remote

controls,

press the ARM

button on each remote control

four

(4)

times,

pausing at

least 1 second in between each press. Make sure that the

horn chirps each time you press the ARM button.

3c.

you

have

three

remaining

remote

controls,

press the

ARM button on the two remote controls

three

(3)

times,

then

press the ARM button on the remaining remote control

twice.

Pause at least 1 seconds in between each press. Make sure

that the horn chirps each time you press the ARM button.

4. Turn the vehicle ignition off to exit the programming mode.

When you are finished, the lost or stolen remote control will

no longer operate your system.

Basic

Troubleshooting

This section outlines some

the basic issues you may experience

while becoming used to the F60/F65. If you have a problem that is not

covered by this section, please consult your installer.

Symptom Problem Solution

Weak or dead battery

Remote control does Change battery

not work Remote control not Program remote

programmed control (page

Door or other Close entrance

entrance is open

System will not arm Courtesy light is on Turn courtesy light off

System is in Valet Turn off Valet mode

mode (page 6)

Hood is open Close hood

System will not start Brake is pressed Release brake

101101·4 F6Q.65.p65 10

9113101,12:14

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Code Alarm Démarreur à distance

Code Alarm

Code Alarm CA 6150 Manuel utilisateur

Code Alarm

Code Alarm CA-430 Manuel utilisateur

Code Alarm

Code Alarm CA-550 Manuel utilisateur

Code Alarm

Code Alarm CA 4051 Manuel utilisateur

Code Alarm

Code Alarm PROFESSIONAL SERIES Manuel utilisateur

Code Alarm

Code Alarm CA 5150 Manuel utilisateur

Code Alarm

Code Alarm ca 4552 Manuel utilisateur

Code Alarm

Code Alarm ca5554 Professional series Manuel utilisateur

Code Alarm

Code Alarm ca6554 Manuel utilisateur

Code Alarm

Code Alarm CA 5051 Manuel utilisateur

Code Alarm

Code Alarm CA-520A Manuel utilisateur

Code Alarm

Code Alarm CA 5150 Manuel utilisateur

Code Alarm

Code Alarm PC 4300 Manuel utilisateur

Code Alarm

Code Alarm professional series PROCOMP Manuel utilisateur

Code Alarm

Code Alarm CA-630 Manuel utilisateur

Code Alarm

Code Alarm CA 5053 Manuel utilisateur

Code Alarm

Code Alarm CA-520 Manuel utilisateur

Code Alarm

Code Alarm PROFESSIONAL CASECRS Manuel utilisateur

Code Alarm

Code Alarm PROFESSIONAL SERIES Manuel utilisateur

Code Alarm

Code Alarm ca6154 Professional Series Manuel utilisateur

Code Alarm

Code Alarm ca5553sst Manuel utilisateur

Code Alarm

Code Alarm ca5154 professional Series Manuel utilisateur

Code Alarm

Code Alarm CSI-100 Manuel utilisateur

Code Alarm

Code Alarm CA 411 Manuel utilisateur

Manuels Démarreur à distance populaires d'autres marques

AstroStart

AstroStart 803U Manuel utilisateur

Durite

Durite 0-649-20 Manuel

EINHELL

EINHELL BT-PS 1000 Manuel

Linear

Linear ACCESS AK-21 Caractéristiques techniques

Soundstream

Soundstream TARANTULA RS.2 Manuel utilisateur

Jaycar Electronics

Jaycar Electronics MB3752 Manuel utilisateur

Ultra Start

Ultra Start 72 Series Manuel utilisateur

ADS

ADS FLASHLOGIC FLRSVW1 Manuel utilisateur

Selecta

Selecta JS012 Manuel utilisateur

Black Widow Security

Black Widow Security BW RAS 400 Manuel utilisateur

Vector

Vector Power City DK080706 Supplément

Ozito

Ozito OJS-800 Manuel utilisateur

Profi-Partner

Profi-Partner 46387 Manuel utilisateur

EZ STARTER

EZ STARTER EZ-45 Manuel utilisateur

Viper

Viper 4204 Manuel utilisateur

Essex Electronics

Essex Electronics KE-1701 Manuel utilisateur

EINHELL

EINHELL EGS 3600 Manuel

Rooboost

Rooboost RB-1750WP Manuel utilisateur