COBAN GROUP G509 Manuel utilisateur
G509 Relay GPS Tracker
User Manual
Preface
Thank you for purchasing the tracker. This manual shows how to operate the
device smoothly and correctly. Make sure to read this manual carefully
before using this product. Please note that specification and information are
subject to changes without prior notice in this manual.
Any change will be integrated in the latest release. The manufacturer assumes
no responsibility for any errors or omissions in this document.
◆Quick using
1）Open device case, proper insert GSM card, connect external power
supply.
2）Put device outside, around 30s three lights will keep lighting on stands
for device can work normally.
3）Dialing device number, it will hang up and reply tracking message with
valid Longitude and latitude.
4）If need track online system, send 2 SMS connects to platform as
below:
SMS1:#IP#123456#220.231.203.248#7700#
SMS2: #apn#123456#APN of operator#APN user name#APN password#
5）Login platform to track in real time(please contact supplier).
1.
Specifications
Content
Specs.
Dim.
33 *31*31 mm
Weight
35g
Network
GSM/GPRS
Band
850/900/1800/1900 Mhz
GPS chip
MTK
GSM module
MTK2503
GPS sensitivity
-159dBm
GPS accuracy
5m
Time To First Fix
Cold status 45s
Warm status 35s
Hot status 1s
Work voltage
9V-80V
Storage Temp.
-40°C to +85°C
Operation Temp.
-20°C to +55°C
Humidity
5%--95%
◆Installation attentions
NOTE: device front side towards the sky.
When install in car, if the windscreen glued by metal thermal insulation
layer or heating layer, it will reduce the GPS receive signal and lead to
GPS work disorder.
Device light description
Light
Represents
yellow
GSM signal normal
blue
GPS signal normal
Red
Power
1.Installation instructions
1.1 Preparation
1.1.1 Open the package to check the device model number is correct, be
with full accessories, or else please contact your supplier.
Choose SIM card, need insert a GSM SIM card into the device, please refer
to the suggestion of your supplier for SIM card choice.
Notice:
Please insert SIM card before turning the device power switch to on;
The SIM card need open the GPRS function;
Please make sure SIM card with full balance.
2.
Device wiring requirements
Open the upper cover and insert the sim card (support NANO card), the
notch is towards the lower left corner
Close the cover and insert it with the broken oil line (the wiring method is as
shown in the picture on the right, be careful not to insert the wrong line)
◆Attentions
◆Device light
1）No yellow light: failed to read SIM card, need reinstall SIM card. 2）Blue
light flash: no GPS signal, make sure device started outside. 3）
Three lights off:
lights entered sleep mode, make a call or move device can wake up.
◆Device failed located
1）
Failed located: message replied with all 0, make sure device started outside
not in room.
2）Can’t reach the call: make sure SIM card has balance and installed
Properly and opened the switch.
◆Device can’t track on platform
1) Check three lights are stable on.
2) Make sure device can work and reply valid tracking long&Lat in SMS.
3) Send SMS #check#123456# , it will reply you device setting
status to check IP,Port,APN etc.
3.User Settings
1.Initialization (initialize the settings)
Text command
Parameter
Example
Command
#super#
#super#
Command Feedback
super ok
2.Single Locating : Two ways
1.Dialing tracking
make a call to device number, it will hang up and reply a real-time tracking
message.
2.SMS tracking
Send SMS command,it will reply your location.
Text command
Parameter
Example
Command
#smslink#password#
#smslink#123456#
Command Feedback
Google link + Speed + Time + Date + IMEI
3.Authorized number (All alarm messages will be sent to authorized number only)
Text command
Parameter
Example
Add Authorized number
#admin#123456#phone number#
#admin#123456#18575518750#
Command Feedback
admin ok
Del Authorized number
#noadmin#123456#phone number#
#noadmin#123456#13409877890#
Command Feedback
noadmin ok（If notified not admin number,send #super# please）
4.Set password
Text command
Parameter
Example
Command
#password#old password#new
passwod#
#password#123456#666888#
Command Feedback
Password ok
5.Set data to upload interval
Text command
Parameter
Example
Command
#at#123456#10~600#
#at#123456#10#
Command Feedback
at ok
Command description
The data upload interval can be set as you need, 10~600 represents seconds
of data uploading interval, default as 10 seconds for real time tracking.
6.Device reboot
Text command
Parameter
Example
Command
#reboot#password#
#reboot#123456#
Command Feedback
reboot ok
Command description
The device will restart within 30 seconds
7.Set all alarm mode
Text command
Parameter
Description
Command
#KC#123456#0#
To close alarm function
Command
#KC#123456#1#
Alarm will reply only SMS
Command
#KC#123456#2#
Alarm will reply only call back
Command
#KC#123456#3#
Alarm will reply via SMS and call
8.Timezone Setting
Text command
Parameter
Example
Command
#timezone#password#direction#time
zone value in hours#time zone in
minutes#
In UTC-6 example:
#timezone#123456#W#6#00#
In UTC+5.30
#timezone#123456#E#5#30#
Command Feedback
timezone ok
9.Check vehicle state
Text command
Parameter
Example
Command
#check#password#
#check#123456#
Command Feedback
IMEI + Authorized number +Alarm mode + IP + GPS status + Data upload interval
status + APN + Time zone + ACC status
10.Geo-fence
Text command
Parameter
Example
Command
#stockade#password#meter#
#stockade#123456#300#
Command Feedback
stockade ok
Command description
send SMS: “#stockade#123456#300#”, “300” represents 300 meters.In
case of breach, it will send SMS “stockade alarm + IMEI + Coordinates” to
the authorized number.
11.Overspeed alarm
Text command
Parameter
Example
Command
#speed#password#speed number in
3 digits#
#speed#123456#060#
Command Feedback
speed ok
Command description
Sample means When the car moves exceeding 60 km/h, the unit will send
SMS alert “speed alarm +imei+ Coordinates ” to the authorized number.
12.Vibration alarm
Text command
Parameter
Description
Command
#vibrate#123456#1#
1 means Slight vibration level
Command
#vibrate#123456#2#
2 means medium vibration level
Command
#vibrate#123456#3#
3 means high sensitive level
Command description
When the tracker detect the vibration,it will send “vibrate alarm + IMEI
+Google map link” to authorized phone number.
13.Cut oil or electricity (Optional with relay)
Text command
Parameter
Example
Command
#stopoil#password#
#stopoil#123456#
Command Feedback
stop oil ok
Command
#supplyoil#123456#
#supplyoil#123456#
Command Feedback
supply oil ok
Table des matières
Autres manuels COBAN GROUP GPS
COBAN GROUP
COBAN GROUP 12000MAH Manuel utilisateur
COBAN GROUP
COBAN GROUP GPS103B Manuel utilisateur
COBAN GROUP
COBAN GROUP TK309 Manuel utilisateur
COBAN GROUP
COBAN GROUP KDL908 Manuel utilisateur
COBAN GROUP
COBAN GROUP TK-STAR Manuel utilisateur
COBAN GROUP
COBAN GROUP tk303 Manuel utilisateur
COBAN GROUP
COBAN GROUP TK103A Manuel utilisateur
COBAN GROUP
COBAN GROUP KDL909 Manuel utilisateur
COBAN GROUP
COBAN GROUP G05 Manuel utilisateur
