Cobalt Digital Inc 9002 Manuel utilisateur
Cobalt Digital Inc.
9002
HD/SD SDI
Distribution Amplifier
Owner’s Manual
9002-OM
Version: 1.0
Page 2 of 18 9002 Owner’s Manual •
••
•(V 1.0)
9002 •
••
•HD/SD SDI Reclocking Distribution Amplifier Owner’s Manual
•Cobalt Part Number: 9002-OM
•Document Version: 1.0
•Printed in the United States.
•Last Author: KGM
•Printing Date: 08/19/08 9:02 AM
The information contained in this Owner’s Manual is subject to change without notice or obligation.
Copyright
© 2008 Cobalt Digital Inc. All rights reserved.
Contents of this publication may not be reproduced in any form without the written permission of
Cobalt Digital Inc. Reproduction or reverse engineering of copyrighted software is prohibited.
Notice
The material in this manual is furnished for informational use only. It is subject to change without
notice and should not be construed as a commitment by Cobalt Digital Inc. Cobalt Digital Inc assumes
no responsibility or liability for errors or inaccuracies that may appear in this manual.
Trademarks
•is a registered trademark of Ross Video Limited.
•is a registered trademark of Cobalt Digital Inc.
•All other product names and any registered and unregistered trademarks mentioned in this
manual are used for identification purposes only and remain the exclusive property of
their respective owners.
9002 Owner’s Manual •
••
•(V 1.0) Page 3 of 18
Important Regulatory and Safety Notices
Before using this product and any associated equipment, refer to the “Important Safety Instructions”
listed below so as to avoid personnel injury and to prevent product damage.
Products may require specific equipment, and /or installation procedures be carried out to satisfy
certain regulatory compliance requirements. Notices have been included in this publication to call
attention to these specific requirements.
Symbol Meanings
This symbol on the equipment refers you to important operating and maintenance
(servicing) instructions within the Product Manual Documentation. Failure to heed
this information may present a major risk of damage or injury to persons or
equipment.
Warning
The symbol with the word “Warning” within the equipment manual indicates a
potentially hazardous situation, which if not avoided, could result in death or serious
injury.
Caution
The symbol with the word “Caution” within the equipment manual indicates a
potentially hazardous situation, which if not avoided, may result in minor or
moderate injury. It may also be used to alert against unsafe practices.
Notice
The symbol with the word “Notice” within the equipment manual indicates a
situation, which if not avoided, may result in major or minor equipment damage or a
situation which could place the equipment in a non-compliant operating state.
ESD
Susceptibility
This symbol is used to alert the user that an electrical or electronic device or
assembly is susceptible to damage from an ESD event.
Important Safety Instructions
Caution
This product is intended to be a component product of the openGearTM frame. Refer
to the openGearTM frame Owner’s Manual for important safety instructions regarding
the proper installation and safe operation of the frame as well as it’s component
products.
Warning
Certain parts of this equipment namely the power supply area still present a safety
hazard, with the power switch in the OFF position. To avoid electrical shock,
disconnect all A/C power cords from the chassis' rear appliance connectors before
servicing this area.
Warning
Service barriers within this product are intended to protect the operator and service
personnel from hazardous voltages. For continued safety, replace all barriers after
any servicing.
This product contains safety critical parts, which if incorrectly replaced may present
a risk of fire or electrical shock. Components contained within the product’s power
supplies and power supply area, are not intended to be customer serviced and should
be returned to the factory for repair.
To reduce the risk of fire, replacement fuses must be the same type and rating.
Only use attachments/accessories specified by the manufacturer.
Page 4 of 18 9002 Owner’s Manual •
••
•(V 1.0)
Environmental Information
The equipment that you purchased required the extraction and use of natural resources for its
production. It may contain hazardous substances that could impact health and the environment.
To avoid the potential release of those substances into the environment and to diminish the need for the
extraction of natural resources, Cobalt Digital encourages you to use the appropriate take-back systems.
These systems will reuse or recycle most of the materials from your end-of-life equipment in an
environmentally friendly and health conscious manner.
The crossed-out wheeled bin symbol invites you to use these systems.
If you need more information on the collection, reuse, and recycling systems, please contact your local
or regional waste administration.
You can also contact Cobalt Digital for more information on the environmental performances of our
products.
9002 Owner’s Manual •
••
•(V 1.0) Page 5 of 18
Contents
Introduction 6
In This Chapter...........................................................................................................................6
A Word of Thanks......................................................................................................................6
Overview....................................................................................................................................6
Functional Block Diagram .........................................................................................................7
Supported Serial Rates...............................................................................................................8
Documentation Terms................................................................................................................8
Installation and Setup 9
In This Chapter...........................................................................................................................9
Static Discharge .........................................................................................................................9
Unpacking..................................................................................................................................9
Rear Module Installation (Optional) ........................................................................................10
Board Installation.....................................................................................................................11
Cable Connections....................................................................................................................11
Card Control and Status ...........................................................................................................12
Card Status.................................................................................................................12
Switches.....................................................................................................................12
Remote Control 13
In This Chapter.........................................................................................................................13
DashBoard Control System Software.......................................................................................13
Service Information 15
In This Chapter.........................................................................................................................15
Troubleshooting Checklist .......................................................................................................15
Warranty and Repair Policy.....................................................................................................16
Ordering Information 17
9002 and Related Products.......................................................................................................17
Contact Us 18
Contact Cobalt Digital Inc........................................................................................................18
Visit us at the Cobalt Digital Inc. website................................................................................18
Page 6 of 18 9002 Owner’s Manual •
••
•(V 1.0)
Introduction
In This Chapter
This chapter includes the following sections:
•A Word of Thanks
•Overview
•Functional Block Diagram
•Supported Audio and Video Formats
•Documentation Terms
A Word of Thanks
Congratulations on choosing the openGearTM 9002 HD/SD Distribution Amplifier. The 9002 is part of
a full line of modular conversion gear for broadcast TV environments. The Cobalt Digital openGearTM
line includes video decoders and encoders, audio embeders and de-embeders, distribution amplifiers,
format converters, and much more. Cobalt openGearTM modular conversion gear will meet your signal
conversion and distribution needs now and well into the future.
Should you have questions pertaining to the installation or operation of your 9002, please contact us at
the numbers listed on the back cover of this manual. We are happy to help with any questions regarding
this or any other openGearTM card.
Overview
The 9002 is a high quality HD/SD Distribution Amplifier. It is capable of equalizing and reclocking an
SDI signal in HD or SD.
The 9002 can equalize an incoming SDI signal using up to 300m of cable at 270 Mbps and up to 120m
of cable at 1.485 Gbps.
9002 Owner’s Manual •
••
•(V 1.0) Page 7 of 18
Functional Block Diagram
SDI IN EQ
DA
DA
DA
DA
SDI OUT
SDI OUT
SDI OUT
SDI OUT
SDI OUT
SDI OUT
SDI OUT
SDI OUT
9002 Block Diagram
DA
SDI OUT
SDI OUT
Page 8 of 18 9002 Owner’s Manual •
••
•(V 1.0)
Supported Serial Rates
The 9002 will reclock 270 Mbps, 1.485 Gbps, and 3 Gbps signals. Signals of other rates will be
equalized and distributed to the outputs, and the reclocker will be bypassed.
Documentation Terms
The following terms are used throughout this guide:
•“Frame” refers to the 8310 frame that houses the 9002 card.
•“Operator” and “User” both refer to the person who uses the 9002.
•“Board” and “Card” all refer to the 9002 card itself, including all components and
switches.
•“System” and “Video system” refers to the mix of interconnected production and
terminal equipment in which the 9002 operates.
9002 Owner’s Manual •
••
•(V 1.0) Page 9 of 18
Installation and Setup
In This Chapter
This chapter includes the following sections:
•Static Discharge
•Unpacking
•Rear Module Installation (Optional)
•Board Installation
•BNC Connections
•Menu Structure
•Factory Defaults
Static Discharge
Whenever handling the card and other related equipment, please observe all static discharge
precautions as described in the following note:
ESD
Susceptibility
Static discharge can cause serious damage to sensitive
semiconductor devices. Avoid handling circuit boards in high
static environments such as carpeted areas, and when wearing
synthetic fiber clothing. Always exercise proper grounding
precautions when working on circuit boards and related
equipment.
Unpacking
Unpack each card you received from the shipping container, and check the contents against the packing
list to ensure that all items are included. If any items are missing or damaged, contact your sales
representative or Cobalt Digital directly.
Page 10 of 18 9002 Owner’s Manual •
••
•(V 1.0)
Rear Module Installation (Optional)
If you are installing the card in a 8310-C-BNC or 8310-BNC frame (one with a 100 BNC rear module
installed across the entire back plane), skip this section.
If you are installing the card into a slot with no rear module, you should have ordered and received a
RM-9002-A Rear Module with your card. You will need to install it in your 8310 frame before you can
connect cables.
Use the following steps to install the RM-9002-A in an 8310 openGearTM frame:
1. Refer to the openGearTM 8310 frame Owner’s Manual, to ensure that the frame is
properly installed according to instructions.
2. On the rear of the 8310, locate the card frame slot.
3. As shown in Figure 2, seat the bottom of the RM-9002-A in the seating slot at the
base of the frame’s back plane.
Figure 2. Rear Module Installation
4. Align the top hole of the RM-9002-A with the screw hole on the top edge of the 8310
back plane.
5. Using a Phillips driver and the supplied screw, fasten the RM-9002-A panel to the
8310 back plane. Do not over tighten.
This completes the procedure for installing the RM-9002-A in an 8310 openGearTM frame.
Table des matières
Autres manuels Cobalt Digital Inc Amplificateur
Cobalt Digital Inc
Cobalt Digital Inc 9910-DA-AV Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc 9232 Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc openGear 9241 Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc 9911DA-8-BPX Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc BlueBox BBG-DA-12G-1x6 Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc 9004 Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc 9910DA-WC Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc 9910DA-AV-EQ Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc 9242 Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc 9001 Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc 9915DA Series Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc 9006 Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc 9003 Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc 5002 Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc openGear 9252 Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc 9910DA-4Q-3G-RCK Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc 5001 Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc 9253 Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc 9910DA Series Manuel utilisateur
Cobalt Digital Inc
Cobalt Digital Inc 9006 Manuel utilisateur
