clivus multrum HIGH PROFILE Manuel utilisateur
CLIVUS MULTRUM
HIGH PROFILE
INSTALLATION & OPERATION MANUAL
IMCM-204-2024-01-30
©Ecoflo Wastewater Management Pty Ltd
TABLE OF CONTENTS
ITEMS REQUIRED (NOT INCLUDED) 1
TOOLS REQUIRED 1
CM HIGH PROFILE SCHEMATICS 2
INSTALLATION 3
STEP 1: POSITION THE PEDESTAL 3
STEP 2: POSITION THE WASTE CHUTE 4
STEP 3: INSTALL THE WASTE CHUTE 5
OPTIONAL EXTRA WASTE CHUTE LENGTHS 6
OPTIONAL: Heater Pad 6
STEP 4: INSTALL THE WHEELS 6
STEP 5: INSTALL THE IN-SERVICE CHAMBER 7
STEP 6: CONNECT THE VENT PIPE AND FAN 8
STEP 7: CONNECT THE FLEXIBLE VENT PIPE AND LIQUID DRAIN HOSE 9
POWERING YOUR FAN 10
LEACHATE DRAIN 11
COMPOST ACCELERATORS 12
STARTING WITH AN EMPTY CHAMBER 13
OPERATION 14
MAINTENANCE 15
ROTATING THE CHAMBERS 16
TROUBLESHOOTING 18
PRODUCT & COMPONENT WARRANTY 20
MAINTENANCE SCHEDULE 21
©Ecoflo Wastewater Management Pty Ltd
IMCM-204-2024-01.30 1
ITEMS REQUIRED (NOT INCLUDED)
Please check the packing slip to ensure everything has been delivered. If anything is
missing, please notify Ecoflo within 72 hrs of receipt.
You will need the following items to complete your installation.
Vent items
• Wall brackets to fix the vent pipe to the building
• A length of 100mm DWV vent pipe to connect to the air exhaust (length depends on
specific installation)
• Dektite if DWV vent pipe will penetrate the roof
Leachate drain items (please check with your local authority)
• Ø100mm Agricultural pipe
• 1.5m x 0.5m Synthetic or Hessian geotextile mat
• 50mm PVC pipe to connect the hose to the agricultural pipe
• 0.30m³ 20mm Aggregate
A vent kit and drain kit are available to purchase separately from Ecoflo.
TOOLS REQUIRED
PVC
CEMENT
SILICONE
Marker Tape Measure Shovel Hand Saw
JigsawPlumb BobPVC CementCaulk Gun
Power Drill Philips Drill Bit Masonry and Brad
Point Drill Bits Hole Saw
Drill Bit
©Ecoflo Wastewater Management Pty LtdIMCM-204-2024-01-30 2
CM HIGH PROFILE SCHEMATICS
If you are planning to excavate an area under the house for the
compost chambers, please ensure the area is well-drained and any
retaining walls are built to the satisfaction of the local authority.
Pedestal
Chute
Min. 750mm
Fan in housing
L.I.T Reducer
Vent pipe
50mm
Vent cowl
Brackets*
100mm DWV pipe*
45° bend
Dektite
(not included)
600mm
600mm
100mm Vent cowl
Camlock fittings
Excess liquid drain hose Leachate drain
In-service
chamber
Out-of-service
chamber
Optional Vent
Installation
©Ecoflo Wastewater Management Pty Ltd
IMCM-204-2024-01.30 3
INSTALLATION
STEP 1: POSITION THE PEDESTAL
Locate the approximate area where you want the pedestal to go before cutting the hole.
The usual position for pedestals is centred between side walls.
NOTE: Due to the pedestals being man made, the distance to the centre may vary from 245
to 255mm. Please check before cutting the hole.
©Ecoflo Wastewater Management Pty LtdIMCM-204-2024-01-30 4
If there is a joist in the way, either
reposition the waste hole OR install
trimmer joists to each end of the cut joist,
and fix all connections with galvanized
framing anchors with 4 nails each leg
(refer to diagram below).
View from under floor
2Following the pedestal floor template, draw a 240mm diameter circle. Cut out the hole with
a jigsaw.
STEP 2: POSITION THE WASTE CHUTE
A 240mm hole must be cut in the toilet room floor to accommodate the waste chute.
1
Go to the underfloor area and look for
the hole you have drilled. Check to see if
there is a floor joist, water pipe or electrical
wiring under the area you are going to cut.
Following the provided pedestal floor template, mark the location of the centre hole 245-
255mm (9.64” -10”) from the back wall. Drill a small hole.
Back wallSide wall
©Ecoflo Wastewater Management Pty Ltd
IMCM-204-2024-01.30 5
STEP 3: INSTALL THE WASTE CHUTE
First ensure the pad or ground level on which the ‘In-service’ chamber will reside is at its final
level beneath the toilet room.
Insert the chute into the hole
12
5
3
Place the chamber (without the
lid) next to the chute. Mark the
height of the chamber onto the
chute.
To install the pedestal, follow the
instructions provided with the
pedestal template.
Cut off the excess chute length
20mm below the mark.
20mm
4Place the chute into hole of the
floor and seal with silicone.
Side wall Back wall
©Ecoflo Wastewater Management Pty LtdIMCM-204-2024-01-30 6
OPTIONAL: Heater Pad
To assist composting in colder
climates, we recommend the purchase
of an optional heater pad which is
permanently fixed inside the chamber.
The Pad will be factory installed. The
Heater Pad runs on 12 Volt Power (refer to
the supplementary manual).
NOTE: The Heater Pad should not be
submerged. Check your ‘Excess Fluid
Outlet’ for blockages regularly.
Push the wheels onto the ends of the axle
until you hear them click.
Place the axle in position under the
chamber.
STEP 4: INSTALL THE WHEELS
OPTIONAL EXTRA WASTE CHUTE LENGTHS
If the underfloor height exceeds 1200mm (floor-to-floor), you will require additional lengths
of chute, fixed together with small stainless steel self-tapping screws below the flange of the
additional waste chute.
As the chute joints are tappered, the top waste chute must be inserted through the toilet
room floor first with additional waste chutes added from below.
©Ecoflo Wastewater Management Pty Ltd
IMCM-204-2024-01.30 7
STEP 5: INSTALL THE IN-SERVICE CHAMBER
Add 50mm of bulking agent to the
chamber.
Hook the chamber bungee loops
around the lid like below.
Slide the lid up the waste chute.
Tip: Install bungee loops under the
floor and knobs on the lid to help hold
it up.
Place the chamber underneath. Lower
the lid onto the chamber, lining it up
with the mixers.
1
4
2
3
©Ecoflo Wastewater Management Pty LtdIMCM-204-2024-01-30 8
STEP 6: CONNECT THE VENT PIPE AND FAN
The fan is IP68 rated so will not be effected by moisture.
100mm DWV vent kit:
• ø100mm DWV Pipes
• ø100mm DWV Slip Joiners
• ø100mm Stand Off Brackets
• Dektite
Extra chamber connection kit:
• Y junction
• Flexible vent pipe
• Pipe connectors
• Male camlock
• Sullage hose
• T-piece
Pedestal
Chute
Min. 750mm
Fan in housing
L.I.T Reducer
Vent pipe
50mm
Vent cowl
Brackets*
100mm DWV pipe*
45° bend
Dektite
(not included)
600mm
600mm
100mm Vent cowl
Camlock fittings
Excess liquid drain hose Leachate drain
In-service
chamber
Out-of-service
chamber
Pedestal
Chute
Min. 750mm
Fan in housing
Y Juntion*
L.I.T Reducer
Vent pipe
T-Piece*
Brackets*
100mm DWV pipe*
45° bend
Dektite
(not included)
600mm
600mm
Vent cowl
Camlock fittings
Excess liquid drain hose
In-service
chamber
Out-of-service
chamber
Leachate drain
OptiOnal Extras
These optional kits are available to purchase from Ecoflo Wastewater Management.
Do not glue the fan
housing to the DWV
fittings.
It is recommended
that the fan runs
24 hours a day
to continuously
circulate air through
the compost heap.
Air is drawn down
the toilet pedestal,
through the compost
chamber and out the
vent pipe.
Optional Installation
Autres manuels pour HIGH PROFILE
1
Table des matières
Autres manuels clivus multrum Toilettes
clivus multrum
clivus multrum HIGH PROFILE Manuel utilisateur
clivus multrum
clivus multrum CM8 Manuel utilisateur
clivus multrum
clivus multrum CM8 Manuel utilisateur
clivus multrum
clivus multrum CM2 Manuel utilisateur
clivus multrum
clivus multrum CM8 Manuel utilisateur
clivus multrum
clivus multrum CM40 Manuel utilisateur
clivus multrum
clivus multrum CM14 Manuel utilisateur
clivus multrum
clivus multrum CM14 Manuel utilisateur
clivus multrum
clivus multrum CM HP Manuel utilisateur
clivus multrum
clivus multrum CM40 Manuel utilisateur
Manuels Toilettes populaires d'autres marques
Better Bathrooms
Better Bathrooms BUN/BeBa 27555/78725 Manuel utilisateur
American Standard
American Standard CONCEPT Cube TF-2704 Manuel utilisateur
BIOLAN
BIOLAN ECO Manuel de la liste des pièces
Thetford
Thetford C260 Series Manuel utilisateur
KELISS
KELISS T162A Series Manuel utilisateur
Kohler
Kohler K-22241K Instructions de montage
