Clinton Electronics Connect PVM Manuel utilisateur
Software Version 1.31.1
Clinton reserves the right, without notification, to make changes in product design & specification.
Connect PVM
User Manual
For models with Built-in
IP or EX-SDI cameras
Table Of Contents
ABOUT
REBOOT
DATE / TIME
FACTORY RESET
LOCATION
UPDATE
SUPPORT
CAMERA SETTINGS
LED SETTINGS
EXIT
NETWORK
Wifi Network
Proxy
Captive Portal
SETUP
Connection Diagram
Remote Control Info
Initial Setup
07
16
08
16
09
17
18
19
20
21
10
11
12
14
01
03
04
1
Based on Software Version 1.31.1. Content subject to change without notice. Check www.clintonelectronics.com for the most current manual.
DC24V
3. ALARM OUT
4. GND
1. ALARM1
3. ALARM OUT
4. GND
2. GND
NETWORK
IP
CAMERA
ON
OFF
To NVR
External
Power
Supply
To DHCP
Network
Connection
NETWORK
VIDEO RECORDER
PoE
CONNECTION DIAGRAM / IP Camera models
4
35
6
7
1. Power Input *required
This is not a PoE device! Main device power requires
a DC24V power supply or 110VAC connection (110VAC
available on select models). Power supply not included,
sold separately.
2. Wifi Antenna *optional
External antenna only oered on 32” and larger models.
Attach antenna if device is to be connected via Wifi.
3. IP Camera Output *optional
Built-in IP camera output only. Connect to NVR or other
network device.
4. Power On/O Switch
After connecting power to device, put the switch to the
ON position. Pressing the Power button on the remote
will not turn On/O the device, it will only turn o the
LCD.
5. Alarm I/O Connections *optional
If desired, make +/- connections from external alarm
output, such as EAS pedestal, to desired Alarm In.
Connections vary by model.
6. Network Connection *required
This connection must either be hardwired or connected
via Wifi for the device to function properly. Cat5e or
higher network cable is recommended. Connect to
DHCP network. There is no communication between
the NETWORK and IP CAMERA ports. If the IP Camera
feed is to be viewed/recorded by an external device,
the additional IP CAMERA port must also be used.
7. VESA 75/100 Mounting hole patterns
1
2
*Actual connections may vary from the image shown.
ATTENTION: This is NOT a PoE Device! Power must come from DC24V or 110VAC power source!
2Based on Software Version 1.31.1. Content subject to change without notice. Check www.clintonelectronics.com for the most current manual.
ON
OFF
DC24V
3. ALARM OUT
4. GND
1. ALARM1
2. GND
NETWORK
ANALOG
OUTPUT
EX-SDI
OUTPUT
External
Power
Supply
To DVR
EX-SDI / HD-SDI
DVR
PoE
To DHCP
Network
Connection
CONNECTION DIAGRAM / EX-SDI Camera models
5
4
3
6
7
8
1
2
*Actual connections may vary from the image shown.
1. Power Input *required
This is not a PoE device! Main device power requires
a DC24V power supply or 110VAC connection (110VAC
available on select models). Power supply not included,
sold separately.
2. Wifi Antenna *optional
External antenna only oered on 32” and larger models.
Attach antenna if device is to be connected via Wifi.
3. Power On/O Switch
After connecting power to device, put the switch to the
ON position. Pressing the Power button on the remote
will not turn On/O the device, it will only turn o the
LCD.
4. Analog Video Output *optional
Connect to Analog DVR or other device.
5. EX-SDI / HD-SDI Video Output *optional
Connect to EX-SDI or HD-SDI compatible DVR or other
device.
6. Alarm I/O Connections *optional
If desired, make +/- connections from external alarm
output, such as EAS pedestal, to desired Alarm In.
Connections vary by model.
7. Network Connection *required
This connection must either be hardwired or connected
via Wifi for the device to function properly. Cat5e or
higher network cable is recommended. Connect to
DHCP network.
8. VESA 75/100 Mounting hole patterns
ATTENTION: This is NOT a PoE Device! Power must come from DC24V or 110VAC power source!
3
Based on Software Version 1.31.1. Content subject to change without notice. Check www.clintonelectronics.com for the most current manual.
REMOTE CONTROL INFO
1. MENU
Press the MENU button to open the Main Menu.
2. EXIT
Press the EXIT button to close the Main Menu or to
go back to the previous menu screen.
3. LEFT / RIGHT / UP / DOWN
Use these directional buttons to navigate the menu
options.
4. ENTER
Press the ENTER button to confirm a menu selection.
5. POWER
Pressing the POWER button will turn o the LCD.
This does not power o the device. While the screen
is o the camera will still have power and output
video to connected devices.
6. MUTE
Press the MUTE button to disable or enable audio on
this device.
7. VOL + / VOL -
Press VOL + to increase the volume level or press
VOL - to decrease the volume level.
3
4
1
2
ATTENTION: The included remote is required to access the Main Menu and make any adjustments to
menu options. Keep the remote in a safe place for future use.
5
6
7
• If the Remote is lost or misplaced a USB mouse can be used to navigate the Main Menu. Plug the mouse into
one of the USB ports on the rear of the device. Move the mouse cursor to the top left corner of the screen, then
click the left mouse button to open the Main Menu.
• When Advertising Content is shown: Pressing LEFT or RIGHT will navigate forwards or backwards through
advertising content playing on the screen.
• Press and hold the POWER button, then select Restart from the menu if the device is unresponsive.
HELPFUL TIPS:
4Based on Software Version 1.31.1. Content subject to change without notice. Check www.clintonelectronics.com for the most current manual.
INITIAL SETUP / Checklist
ATTENTION: Verify that the following information is completed before proceeding with the installation.
Do you have the Store Number and Device Group information?
If previously set up by the Clinton Connect admin, there may be additional information that is relevant to your
installation. This information includes the Store Number and/or Device Group. This information is not technically
required to complete the installation and can be changed at a later date.
Is the Connect PVM installed vertically?
Verify the Connect PVM is installed correctly. It should have a vertical
orientation (portrait mode) with the camera located at the bottom
of the device. If the device is installed horizontally both the camera
feed on connected DVR/NVR and the digital signage content will not
display correctly.
Will this be a wired or wireless internet (Wifi) connection?
The Connect PVM is a networked device that requires internet access
to function correctly. If this device can not access the internet, it can
not be completely setup and will not be able to receive advertising
updates. This device will accept either a wired or Wifi internet
connection. For best results a wired connection is recommended.
Do you have the Remote that was included with the PVM?
The included remote is required to complete the initial set up. Keep
the remote in a safe place to make any adjustments at a later date.
Do you have the QR Code?
The company specific QR Code is required to register the device to
the correct company. If the QR Code was not provided contact your
Clinton Connect admin.
Has the network been properly configured?
Depending on the level of network security, some URLs may need to be white-listed on the network. If the
required URLs are not added, the initial set up will fail. For a list of the required URLs consult the Networking
Requirements document which can be found on www.clintonconnect.com/support
5
Based on Software Version 1.31.1. Content subject to change without notice. Check www.clintonelectronics.com for the most current manual.
Step 1. Press the ENTER button on the included remote
to get started.
Step 3. After successful network connection, the
device will test it’s Internet Connection and ping
the Clinton Connect Server. Both tests must pass to
proceed with the setup.
INITIAL SETUP
Step 2. Choose a Wifi Network from the list, enter the
password, and select Join.
Step 4. Hold the QR code in front of the Connect PVM
camera to scan. If the code does not scan, you can also
enter it manually.
*Hardwired devices will automatically skip this step
ATTENTION: This device requires a network connection with access to the internet to complete the
initial setup.
6Based on Software Version 1.31.1. Content subject to change without notice. Check www.clintonelectronics.com for the most current manual.
INITIAL SETUP
Step 7. Begin typing the store number when prompted,
then choose your store number from the list. Store
numbers will only appear if they have been entered
previously on Clinton Connect.
Step 8. Select the appropriate device group from
the list to automatically download assigned content.
If there is no content, the device will display the full-
screen camera view until the next deployment to that
device or device group.
Step 6. Press the ENTER button on the remote to Snap
a Photo. This photo is used to help verify the device is
installed in the correct location.
Choose to Accept or Redo the photo.
Step 5. Once the QR Code has scanned, verify the
correct time and date by selecting YES. If the time is
not correct, select NO, then select the correct time
from the list.
7
Based on Software Version 1.31.1. Content subject to change without notice. Check www.clintonelectronics.com for the most current manual.
Press the MENU button on the remote to display the Main Menu, then select About. The About screen has basic
information about the device that may be useful during setup or in the event you need technical support.
13” Test Connect PVM
Welcome Ads
Ads 10.1.2019 13.29
Clinton Electronics
C6701E
Main Entrance
CE-P13-B
ABOUT
ATTENTION: Models with built-in IP cameras— IP Camera information WILL NOT be shown on this
screen. IP Camera information can only be viewed after making a connection to the IP Camera (output)
located on the back of the Connect PVM, then accessing camera via internet browser or other network
device/software.
8Based on Software Version 1.31.1. Content subject to change without notice. Check www.clintonelectronics.com for the most current manual.
DATE/TIME
It is important that the date and time information is set correctly during installation. If the date and time are not correctly
set, scheduled content will not display at the appropriate time.
Set Time Zone. If the Date & Time information is
incorrect, select this to pick a new Time Zone from a
list.
Use the UP or DOWN arrows on the remote to scroll
through the list. Press the ENTER button to select the
correct Time Zone.
Press the EXIT button to leave this screen.
Table des matières
