Climecon ECO-W Manuel utilisateur

climecon.fi

Installation manual ECO-W

1. Components of the ECO-W

air heater

1. Body, duct connection, heating element,

electronics section and connections for supply

voltage (230 V) and controller cabling.

2. Grille

3. Grille fastening screw (2 pcs)

4. Bottom fastening screw (for the wall, 2 pcs)

Figure 2.1

2. Installation of the ECO-W air heater

1. Drill the necessary holes in the wall for cables and fastening screws by using

the template provided with the unit (see stencil in Appendix 1).

2. The minimum distance of the terminal device from the ceiling is 100 mm (see Figure 2.1).

Install the terminal device at a minimum height of 1.8 m.

Ensure that children cannot get their hands on the device.

3. 

4. Insert the bottom section duct connector into the inlet air duct, and attach the body to the wall with screws (4)

(2 pcs, max Ø 5 mm).

5. Connect the supply cable (MMJ) through a double-pole switch, and the control unit’s data cable

to the connectors in the electronics section of the terminal device, as shown in Figure 2.2.

6. Ensure that the connections are correct. Place the grille back onto the body and

ensure that it is properly attached with the fastening screws.

7. Mark the power switch clearly.

Figure 2.2

Figure 1.1

230VAC

CONTROL

Modbus

TERMINATION

OFF-ON

DIP1-8:

Modbus-ID

OFF/ON

D- D+ V

B A

CONTROL BUS

09.20

ECO-W distance from wall

Min. 10 mm

climecon.fi

Installation manual ECO-W

3. Connection

1. 

N and L in the electronics section of the terminal device, as shown in Figures 3.2 and 3.3.

2. Connect the ground to the terminal device’s separate ground connector, as shown in Figures 3.2 and 3.3.

3. Connect the ECO series terminal device to the controller with the data cable, as shown in Figures 3.2 and 3.3.

4. Activate the terminator by moving the termination jumper to the ON position



5. DIP switch operation:

• One thermostat controls one terminal device: there is no need to change the position of the DIP switches.

 

 

move the DIP switch No 8 to the ON position.

NOTE! Electrical connections may only be made by a professional electrician.

WARNING! The supply air device carries a voltage of 230V.

U = 230V In = 1.7A

The connect signal D-/D+ is RTU.

For the BMS connection settings, see Appendix 1. ECO ModBus map.

The recommended data cable between the controller and the air heater is e.g., NOMAK 2x2x0.5+0.5

230VAC

CONTROL

Modbus

TERMINATION

OFF-ON

DIP1-8:

Modbus-ID

230VAC

CONTROL

Modbus

TERMINATION

OFF-ON

OFF/ON

DIP1-8:

Modbus-ID

D- D+ V

B A

CONTROL BUS

OFF ON

Bus

termination

by jumper

OFF ON

Bus

termination

by jumper

CONTROL Modbus-ID

ID: 1-4

1 =

2 =

3 =

4 =

Figure 3.1

climecon.fi

Installation manual ECO-W

The basic ECO connection, in which one ECO air heater

is controlled with a single ECO-T room control unit.

230VAC

CONTROL

Modbus

TERMINATION

OFF-ON

DIP1-8:

Modbus-ID

OFF/ON

D- D+ V

B A

CONTROL BUS

ECO-T

D- D+ V

N L

Control BUS

B A

230 VAC

Room

ECO air heater

One ECO-T

control unit can

control 1–4ECO

air heaters



are controlled with a single ECO-T room control unit.

230VAC

CONTROL

Modbus

TERMINATION

OFF-ON

DIP1-8:

Modbus-ID

230VAC

CONTROL

Modbus

TERMINATION

OFF-ON

OFF/ON

DIP1-8:

Modbus-ID

D- D+ V

B A

CONTROL BUS

OFF ON

Bus

termination

by jumper

OFF ON

Bus

termination

by jumper

CONTROL Modbus-ID

ID: 1-4

1 =

2 =

3 =

4 =

ECO-T

D- D+ V

N L

Control BUS

B A

230 VAC

Room

ECO air heater

D- D+ V

N L

ECO air heater

One ECO-T

control unit can

control 1–4ECO

air heaters



a separate ECO-T control unit.

Move the DIP switch No 8 to the ON position.

The heating resistor’s maximum surface



230VAC

CONTROL

Modbus

TERMINATION

OFF-ON

DIP1-8:

Modbus-ID

230 VAC

huone-

säädin

L-in L-out

Figure 3.2

Figure 3.3

Figure 3.4

climecon.fi

Installation manual ECO-W

4. Connecting the heating of several rooms to the bus

1. 

The ECO connection in which the heating of several rooms has been

linked through the bus. In the example, Room No 1 has two

heaters and Room No 2 has one heater.

D- D+ V

N L

Control BUS

230 VAC

Room 1

Master Slave

ECO-T

D- D+ V

B A

ECO air heater

D- D+ V

N L

ECO air heater

One ECO-T

control unit

can control

1–4ECO air

heaters

One ECO-T

control unit

can control

1–4ECO air

heaters

ECO-T

D- D+ V

N L

Control BUS

B A

230 VAC

Room 2

ECO air heater

The ECO connection in which the heating of several rooms has been linked

through the bus.

D- D+ V

B A

CONTROL BUS

BUS

Term.

OFF

D- D+ V

B A

CONTROL BUS

BUS

Term.

ECO air heater

BUS:

Modbus-ID: 1..9

BUS:

Master

D- D+ V

B A

CONTROL BUS

BUS

Term.

Modbus settings

Modbus ID

Stop bits

Baudrate

Master

38400

Modbus settings

Modbus ID

Stop bits

Baudrate

38400

Modbus settings

Modbus ID

Stop bits

Baudrate

38400

NOTE! Electrical connections may only be made by a professional electrician.

WARNING! The supply air device carries a voltage of 230V.

U = 230V In = 1.7A

The connect signal D-/D+ is RTU.

For the BMS connection settings, see Appendix 1. ECO ModBus map.

The recommended data cable between the controller and the air heater is e.g., NOMAK 2x2x0.5+0.5

Figure 4.1

Figure 4.2

climecon.fi

The ECO connection in which the heating of several rooms has been linked through the bus and the data transfer between the

rooms is done via a BMS (Building Management System) device.

D- D+ V

N L

Control BUS

230 VAC

Room 1

SlaveECO-T

D- D+ V

B A

ECO air heater

D- D+ V

N L

ECO air heater

One ECO-T

control unit can

control 1–4ECO

air heaters

One ECO-T

control unit can

control 1–4ECO

air heaters

ECO-T

D- D+ V

N L

Control BUS

B A

230 VAC

Room 2

ECO air heater

BMS

Slave

Master

Figure 4.3

climecon.fi

Installation manual ECO-T, controller

21.0

230VAC

CONTROL

Modbus

TERMINATION

OFF-ON

DIP1-8:

Modbus-ID

OFF/ON

D- D+ V

B A

CONTROL BUS

Figure 1.1

Figure 2.1

Figure 3.1

3. Start-up guide

1. Connect the supply voltage to the system,

which will activate the touch screen’s main view

(Figure 3.1).

2.  



3. Set the language, date and time.

4. You can change the language by navigating to the

Language section in the Display settings menu.

 .

5. The date and time can be set in

the Date & Time section.

6. To return to the main view, press again

 

7. The temperature can be adjusted in the main

view with the plus and minus symbols.

8. More detailed instructions on the system

functions are provided in a separate manual.

2. Controller installation:

1. Run the ECO-T controller unit’s data cable

from the ECO air heater to the junction box,

as shown in Figure 2.1.

2. Detach the touch screen (4) from the locking

piece (3).

3. Detach the locking piece from the bottom (1),

for example with a small screwdriver.

4. Fasten the bottom (1) to the junction box.

5. Install the cover plate (2).

6. Install the locking piece (3).

7. Connect the wires to the touch screen

connectors, as shown in Figure 2.1.

8. Push the touch screen (4) into the locking piece

(3) until you hear a click.

1. Components of the ECO-T controller

1. Bottom

2. Cover plate

3. Locking piece

4. Touch screen

More comprehensive instructions

for adjusting and scheduling room

temperature can be found via the

QR code or at climecon.ﬁ/eco

climecon.fi

Installation manual ECO-W

NOTE! Electrical connections may only be made by a professional electrician.

Always disconnect the device from the supply voltage before maintenance!

OFF

230 VAC

Data

climecon.fi

Maintenance manual ECO-W

NOTE! Maintenance may only be performed by a professional ventilation installer.

Warning! The device carries a voltage of 230V!

Disconnect from the supply voltage before maintenance.

OFF

climecon.fi

1.ECO ModBus map ; Appendix 1. ECO ModBus map

Holding

registers (4x) Unit/Value Description

1Status

2Application state 0=normal (home), 1=away

3Not used

4 Temperature setpoint  

211 Date.year Not able to set via modbus

212 Date.month Not able to set via modbus

213 Date.day Not able to set via modbus

214 Clock.hours Not able to set via modbus

215 Clock.minutes Not able to set via modbus

216 Clock.seconds Not able to set via modbus

2000 Week timer master

  

2001 Week program1

 







2002 Not used Must be 1

2003 Week program 1

- Comfort start time



NOTE ! Must be dividable by 15

2004 Week program 1

- Comfort end time



NOTE ! Must be dividable by 15

2005 Week program 1

- Comfort temperature  

NOTE ! Must be dividable by 5 (0,5°C)

2006 Week program 1 -

Economy temperature  

NOTE ! Must be dividable by 5 (0,5°C)

 





2008 Not used Must be 1

2009 Week program 2 - Com-

fort start time



NOTE ! Must be dividable by 15

2010 Week program 2 - Com-

fort end time



NOTE ! Must be dividable by 15

2011 Week program 2 - Com-

fort temperature  

NOTE ! Must be dividable by 5 (0,5°C)

2012 Week program 2 -

Economy temperature  

NOTE ! Must be dividable by 5 (0,5°C)

2013 







climecon.fi

ECO series ModBus register map

Holding

registers (4x) Unit/Value Description

2014 Not used Must be 1

2015 Week program 3

- Comfort start time



NOTE ! Must be dividable by 15

2016 Week program 3

- Comfort end time



NOTE ! Must be dividable by 15

 Week program 3

- Comfort temperature  

NOTE ! Must be dividable by 5 (0,5°C)

2018 Week program 3

- Economy temperature  

NOTE ! Must be dividable by 5 (0,5°C)

2019 Week program 4

 





2020 Not used Must be 1

2021 Week program 4

- Comfort start time



NOTE ! Must be dividable by 15

2022 Week program 4

- Comfort end time



NOTE ! Must be dividable by 15

2023 Week program 4

- Comfort temperature  

NOTE ! Must be dividable by 5 (0,5°C)

2024 Week program 4

- Economy temperature  

NOTE ! Must be dividable by 5 (0,5°C)

2025 





2026 Not used Must be 1

 Week program 5

- Comfort start time



NOTE ! Must be dividable by 15

2028 Week program 5

- Comfort end time



NOTE ! Must be dividable by 15

2029 Week program 5

- Comfort temperature  

NOTE ! Must be dividable by 5 (0,5°C)

2030 Week program 5

- Economy temperature  

NOTE ! Must be dividable by 5 (0,5°C)

35001 Parameter system

version Read only

35002 Not used (NULL) Read only

35003 Not used (NULL) Read only

35004  Read only

35005 Parameter request

revision Read only

Table des matières

Autres manuels Climecon Chauffage

Climecon

Climecon ECO2 Manuel utilisateur

Climecon

Climecon Climecon ECO4 Manuel utilisateur

Climecon

Climecon ECO1 Manuel utilisateur

Climecon

Climecon ECO4 Manuel utilisateur

Climecon

Climecon ECO-C Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur