Climecon TUISKU Manuel utilisateur

The mounting instructions are the same for the following product series:

TUISKU-VU and TUISKU-PU

TUISKU-AF

TUISKU-O

TUISKU-IS

The connection instructions of TUISKU-AF is in separate connection manual

TUISKU

ﬂush-mounted

snow covers

Installation manual

climecon.

0322

TUISKU ﬂush mounting

It is advisable to build a chamber with a drainage similar toFigure 1 or 2 behind the TUISKU snow covers to

prevent moisture from getting into the ducts in exceptionally demanding conditions.

Figure 1 is common in multielement TUISKU installations and Figure 2 when there is a one-piece TUISKU

installation and a back seam.

Kammio TUISKUn takana

rauhoittaa ilmavirran nopeuden,

mikä edesauttaa mahdollisen

läpi päässeen kevyen pakkaslu-

men laskeutumisen kammion

pohjalle ilman, että se kulkeutuu

pidemmälle kanavistossa.

Kaivo + saattolämmitys / lumen sulatus

Max. 0,7 m/s

< 2 m/s

Vedenpoisto + lumensulatus

Aukko ~15 mm asennusvaran verran suurempi

Tarkastusluukku

max. 0,7 m/s

TUISKU elements are designed to

perform at high face velocities but

the maximum recommended face

velocity is 0.7 m/s.

1

2

The chamber behind TUISKU calms

-

litates the possible settling of light

frosty snow at the bottom of the

chamber without passing further

through the ductwork.

Water drainage hole + heat tracing / snow melting



Inspection hole

Drainage + snow melting

climecon.fi

1-piece

TUISKU ﬂush mounting

Seal the edge behind the TUISKU frame so that TUISKU can be installed tightly.

 

Mount TUISKU to a load-bearing wall with screws.

We recommend the following methods or equivalent to mount TUISKU to a wall:



• Concrete: Concrete screw Fisher FBS 6x40/5 mm US or equivalent



• Steel: EJOT JT2-6-6.3x25mm zinc-plated drill point

1

2

3

climecon.fi

3-piece elements in parallel

TUISKU ﬂush mounting

Seal the edge behind the TUISKU frame so that TUISKU can be installed tightly.

 

We recommend the following methods or equivalent to mount TUISKU to a wall:



• Concrete: Concrete screw Fisher FBS 6x40/5 mm US or equivalent



• Steel: EJOT JT2-6-6.3x25mm zinc-plated drill point

Mount the TUISKU elements together with zinc-plated drill point screws EJOT JT2-6-6.3x25mm.

1

2

3

1

2

3

1

2

3

climecon.fi

3-piece elements on top of one another

TUISKU ﬂush mounting

Seal the edge behind the TUISKU frame so that TUISKU can be installed tightly.

 

We recommend the following methods or equivalent to mount TUISKU to a wall:



• Concrete: Concrete screw Fisher FBS 6x40/5 mm US or equivalent



• Steel: EJOT JT2-6-6.3x25mm zinc-plated drill point

Mount the TUISKU elements together with zinc-plated drill point screws EJOT JT2-6-6.3x25mm.

11

22

33

1

2

3

1

2

3

climecon.fi

TUISKU ﬂush mounting

TUISKU-AK installation frame (accessory)

 



 

from hot galvanized structural steel S320GD+Z350 3.0 mm or equivalent..

We recommend the following methods or equivalent

to mount the TUISKU-AK installation frame to the opening:

• Wood: TX-20 4.5X40 zinc-plated countersunk head full thread chipboard screw

• Concrete: Concrete screw Fisher FBS 6x40/5 mm US or equivalent



• Steel: EJOT JT2-6-6.3x25mm zinc-plated drill point



to make installing the multielement TUISKU

pieces easier. The dimensions of the installation







the edges of the opening must be supported



NOTE! The TUISKU-AK installation frame

must not be a part of a load-bearing structure!

The load-bearing structure must be designed

and approved by a structural engineer.

When installing TUISKU elements without an



built in the opening for TUISKU with the struc-

tural engineer’s instructions.

1

2

2a 2b Sandwich

structure

Interior

Exterior

50 mm 50 mm

30 mm 30 mm

Width of the

element

Width of the

element

climecon.fi

Multielement TUISKU + TUISKU-AK installation frame

TUISKU ﬂush mounting

 

 



in the opening for TUISKU with the structural engineer’s instructions.





 

The bearing frame can be turned if needed.

NOTE! The TUISKU-AK installation frame must not be a part of the building’s load-bearing structures.

We recommend the following screw types or equivalent

to mount the support frame inside the opening or to the edges of the opening:

• Wood: TX-20 4.5X40 full thread chipboard screw csk.hd. Zn

• Concrete: Concrete screw Fisher FBS 6 x 40/5 mm US or equivalent



• Steel: EJOT JT2-6-6.3 x 25 mm zinc-plated drill point

The structure must always be approved by a structural engineer.

1

2

3a

3b

2

296 mm

3a 3b

152

100

105

56

Ø10

Ø8

climecon.fi

A

ASECTION A-A

B

A

ASECTION A-A

B

1

2

3

4

Multielement TUISKU + TUISKU-AK installation frame,

for example 4-piece

TUISKU ﬂush mounting

Seal the edge behind the TUISKU frame so that TUISKU can be installed tightly.

 

• The upper edges and the sides of the lower TUISKU elements are mounted from its rear end



• The lower edges and one side are mounted to the load-bearing wall structure.

 

correspondingly mounted to the installation frame and the load-bearing wall structure.

 

drill point screw EJOT JT2-6-6.3x25 mm

The TUISKU elements are mounted together from the sides and the top with zinc-plated

drill point screws EJOT JT2-6-6.3x25mm.

12

34

= double screws.

In vertical sections

2 screws side-by-side

and in horizontal

sections 2 screws on

top of one another.

1

2

3a

3b

climecon.fi

1

2

3

6

Multielement TUISKU + TUISKU-AK installation frame,

for example 6-piece

TUISKU ﬂush mounting

Seal the edge behind the TUISKU frame so that TUISKU can be installed tightly.

 

• The upper edges and the sides of the bottom corner TUISKU elements are mounted from



• The lower edges and one side are mounted to the load-bearing wall structure.

• The bottom edge of the middle TUISKU element is mounted to the load-bearing structure





correspondingly mounted to the installation frame and the load-bearing wall structure.

 

EJOT JT2-6-6.3x25mm.

The TUISKU elements are mounted together from the sides and the top with zinc-plated

drill point screws EJOT JT2-6-6.3x25mm.

123

4

= double screws.

In vertical sections 2 screws side-by-side and in

horizontal sections 2 screws on top of one another.

A

ASECTION A-A

B

A

ASECTION A-A

B

56

4

5

1

2

3a

3b

climecon.fi



Fasten the wires as shown in the picture.



Installation of TUISKU-IS snow and rain cover with

removable grille

1

2

3

Vaijeri

We recommend the following methods or equivalent to mount TUISKU to a wall:



• Concrete: Concrete screw Fisher FBS 6x40/5 mm US or equivalent



• Steel: EJOT JT2-6-6.3x25mm zinc-plated drill point

Vaijeri

climecon.fi

Climecon TUISKU Manuel utilisateur

Manuels Ventilateur populaires d'autres marques