CliMATE MCM230 Manuel utilisateur

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

PRODUCT MANUAL

MCM230

PORTABLE AIR CONDITIONER

PRODUCT MANUAL MCM230 PORTABLE AIR CONDITIONER

Page 2

WARNINGS

These instructions should be read by:

The specifying engineer.

The installation engineer.

The user.

The service engineer.

• Failure to follow these instructions may result in risk of personal injury or damage to the

equipment.

• Damage due to a failure to follow these instructions will invalidate the warranty.

• The appliance must be serviced by qualied engineers in compliance with local regulations.

• The appliance must be switched o󰀨 and disconnected from the power supply before any work

is carried out.

• There are no user controls inside the appliance casing.

• Do not place anything on top of the appliance.

• An air gap of at least 300mm should be allowed at the front and rear of the unit to ensure a

clear airow.

• Do not disconnect the appliance from the supply under load.

• For internal use only. Do not use out of doors.

• Extension cables should be correctly rated for the load,fully unwound and never run through

water or over sharp edges.

• Always transport and store in an upright position.

• Maximum operating temperature 35°C.

• Minimum operating temperature 21°C.

SPECIFICATIONS:

The MCM230 is a Mono-block portable air conditioning unit. It is connected to a 13 Amp. 230Vac. 50Hz power supply

and comes tted with a fused uk moulded plug.

It is recommended that the supply to the machine should be protected by a 30mA RCD

PRODUCT MANUAL MCM230 PORTABLE AIR CONDITIONER

Page 3

SET UP AND OPERATION:

• The unit is designed to operate between 21°C and 35°C. Operation outside of these temperatures could cause

compressor failure and will invalidate the warranty. If the temperature in the room is above 35 C it is recommend-

ed that all the doors and windows are opened and the unit run on Fan only to reduce the temperature.

• Site the unit on a rm level surface and apply the castor brakes. Do not operate the machine without engaging

the castor brakes.

• Attach the 400mm exhaust duct and route to a suitable discharge point. Keep the duct as short and straight as

possible. Do not operate the unit if the hose is kinked or puntured. Do not exceed the supplied length of exhaust

duct.

• Should air need to directed to a particular area t the air discharge hoses to the front outlets and extend to the

desired discharge points. Do not exceed 1.25M per hose.

• Check that the water drain tank is correctly located in it's housing and the exible drain hose is inserted into the

tank.

• Connect the unit to a 230Vac 50Hz power supply and check that the 'Power On' lamp is illuminated.

• Turn the 'Fan On' switch to 'I' to start the fans.

• Turn the 'Cooling On' switch to 'I' to start the compressor. It should be noted that the compressor will not start if

the fans are not running or the ambient temperature is below 21°C. The compressor is tted with a start delay

timer and will not run for 3 minutes from activation of the cooling switch. This device is designed to protect the

compressor from repeated start/stop cycles.

• Allow a minimum of 10 minutes for the unit to start cooling.

• During the cooling process the unit will produce condensate (water) which will drain into the water drain tank.

Once this tank lls to a set level it will switch the compressor and fans o󰀨 and illuminate the 'Tank Full' lamp.

• Before removing the water drain tank, and to avoid any potentially damaging water spillage, switch the fans and

cooling o󰀨 and allow 5 minutes for any accumulated moisture within the machine to drain into the tank.

• To empty the tank carefully remove it from the machine using the grab handle on the top by lifting and sliding it

forwards. Do not loosen or remove the large screw cap on the front of the tank. Once the tank is emptied replace

it in the housing ensuring it is correctly located and that the exible drain hose is inserted into the tank.

• The machine can now be restarted.

• Ensure the water drain tank is empty prior to transportation.

• Do not remove the water drain tank while the machine is operating.

PRODUCT MANUAL MCM230 PORTABLE AIR CONDITIONER

Page 4

OPERATION AND CONTROLS:

Discharge

hoses

Water drain

tank

Locking castors

Exhaust

discharge

Fans on

rocker

switch

Cooling on

rocker switch

Tank full

lamp

Power on

lamp

OPTIONAL THERMOSTAT:

The MCM230 may come with an optional thermostat. To achieve maximum cooling capacity rotate the thermostat

fully anti-clockwise.

PRODUCT MANUAL MCM230 PORTABLE AIR CONDITIONER

Page 5

MAINTENANCE:

1. Check and clean the evaporator and condenser heat exchanger coils. Build up of dust and dirt can severly e󰀨ect

the performance of the machine. Remove the front and rear panels and clean with compressed air.

2. Periodically check the water tank drain mechanism is operating correctly and the drain hose is present and in

good condition.

3. Regularly inspect the mains cable and plug for signs of damage or wear. Do not operate the machine with a

damaged mains cable.

4. Check that the castors are running freely and that the breaking mechanisms are working correctly.

TROUBLESHOOTING GUIDE:

PROBLEM POSSIBLE CAUSE SOLUTION

Machine fails to operate Power Failure

Check power on lamp is illuminated.

Check unit is connected to the power supply.

Check plug fuse for failure and correct 13A

rating

Check Building circuit is not overloaded.

Poor cooling performance.

‘Tank Full’ lamp illuminated Empty water tank.

Cooling not selected Switch cooling on

If tted, Thermostat knob not turned fully anti-

clockwise

Turn knob fully anti-clockwise.

Allow 3 minutes for compressor to start and 10

minutes for cooling.

Coils dirty

Filters dirty. (where tted)

Exhaust hose too long or kinked.

Exhaust outlet restricted or blocked.

Clean coils. See Maintenance.

Clean lters. See Maintenance.

Ensure maximum duct length is not exceeded.

Ensure duct is run as straight as possible and is

venting correctly al it’s exit point.

Air inlet grills obstructed Remove obstruction.

Water leaking.

Clogged drain hose.

Water drain tank missing

Remove blockage.

Replace tank

Tank full and tank mechanism not working

correctly.

Check tank mechanism operates correctly.

Ensure ‘Tank Full’ lamp illuminates when

mechanism is actived.

Drain hose not correctly located in tank. Ensure drain hose is located inside the tank.

Compressor stops working. Input voltage too low.

Water drain tank full

Check line voltage.

Check water drain tank is not full

SHOULD YOU CONTINUE TO EXPERIENCE PROBLEMS PLEASE CONTACT THE SUPPLIER.

PRODUCT MANUAL MCM230 PORTABLE AIR CONDITIONER

Page 6

EXPLODED VIEW:

PRODUCT MANUAL MCM230 PORTABLE AIR CONDITIONER

Page 7

SPARE PARTS:

ITEM No PART No DESCRIPTION PRICE

1BW0201220 TOP REAR PANEL POA

2FA010124 CONDENSER FAN POA

3BW0201221 CENTRE PANEL POA

4BW0201222 REAR PANEL POA

5FR030211 CONDENSER COIL POA

6FR010122 COMPRESSOR POA

7EL020108 MAINS CABLE POA

8ME040305 TRUNK HANDLE POA

9BW0201223 RIGHT SIDE PANEL POA

10 ME010211 100mm FIXED CASTOR POA

11 BW0201224 BASE PANEL POA

12 ME010212 100mm SWIVEL CASTOR POA

13 BW0201225 LOWER FRONT PANEL POA

14 ME040137 CONDENSATE TANK POA

15 BW0201226 EVAPORATOR PANEL POA

16 FR030111 EVAPORATOR COIL POA

17 EL030145 SPEED CONTROLLER POA

18 BW0201230 GALVANISED DRIPTRAY POA

19 BW0201229 LEFT SIDE PANEL POA

20 FA010317 EVAPORATOR FAN POA

21 BW030201 1500 DUCT C/W PLASTIC COLLAR POA

22 ME040201 CABLE GLAND AND LOCKNUT POA

23 BW0201232 FRONT TOP PANEL POA

24 EL030111 55uf CAPACITOR POA

25 EL020423 MODULAR TERMINAL BLOCK POA

26 EL030704 INDICATOR LIGHT POA

27 EL030109 0/1 ROCKER SWITCH POA

28 EL020415 40A TERMINAL BLOCK POA

29 EL030101 MICROSWITCH POA

30 ME040526 SPRING POA

31 EL020423 MODULAR TERMINAL BLOCK POA

32 EL030403 DIGISTAT XR10 POA

33 BW0201233 ELECTRICS PLATE POA

34 EL030201 SLAVE RELAY POA

35 BW0201228 SWITCH PLATE POA

36 BW030110 EXHAUST DUCT. (NOT SHOWN) POA

37 BW030438 FASCIA LABEL (NOT SHOWN) POA

38 FR020101 3/8 COPPER PIPE (NOT SHOWN) POA

39 FR020301 20g FILTER DRIER (NOT SHOWN) POA

40 FR010302 3/8 INSULATION TUBE (NOT SHOWN) POA

PRODUCT MANUAL MCM230 PORTABLE AIR CONDITIONER

Page 8

Table des matières

Autres manuels cliMATE Climatiseur

cliMATE

cliMATE WPC-18000 Manuel utilisateur

cliMATE

cliMATE CM-8000E Manuel utilisateur

cliMATE

cliMATE WSC 168 Manuel utilisateur

Manuels Climatiseur populaires d'autres marques

Spheros

Spheros CC 355 Manuel utilisateur

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manuel utilisateur

Panasonic

Panasonic CS-E12HKEW Manuel utilisateur

nedis

nedis ACMB1WT7 Manuel utilisateur

Samsung

Samsung AR KV Series Mode d’emploi

Daikin

Daikin FCFV50A Manuel utilisateur

Fujitsu

Fujitsu Inverter ASBA30JFC Manuel utilisateur

Toshiba

Toshiba RAS-M10SMUV-E Manuel utilisateur

Daikin

Daikin FXLQ20MAVE Manuel utilisateur

Hitachi

Hitachi RAS-E24CAK Manuel utilisateur

CIAT

CIAT Magister 2 Series Mode d’emploi

Bestron

Bestron AAC6000 Manuel utilisateur

Hisense

Hisense 7K Manuel technique

Frigidaire

Frigidaire FFRE0533S1E0 Manuel utilisateur

Samsung

Samsung AS09HM3N Manuel utilisateur

Frigidaire

Frigidaire CRA073PU11 Manuel du propriétaire

Soleus Air

Soleus Air GB-PAC-08E4 Manuel utilisateur

McQuay

McQuay MCK020A Manuel utilisateur

cliMATE MCM230 Manuel utilisateur

Manuels Climatiseur populaires d'autres marques