Clifford AVANTGUARD 5 Manuel utilisateur

installation guide

www.directed.com

Bitwriter™, Code Hopping™, Directed®, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn Routine™,

Nite-Lite®, Nuisance Prevention Circuitry®, NPC®, Revenger®, Silent Mode™, Soft Chirp®, Stinger®, Valet®,

Vehicle Recovery System®, VRS®, and Warn Away® are all Trademarks or Registered Trademarks of Directed

Electronics, Inc., Vista, California.

IIMMPPOORRTTAANNTT!!Please note that this manual was intended for US consumers

and therefore includes American phrases or words.

warning! safety first . . . . . . . . . . .5

before beginning the

installation . . . . . . . . . . . . . . . . .6

what is included . . . . . . . . . . . . . .7

transmitter configurations . . . . . .7

transmitter functions . . . . . . . . . .8

standard configuration . . . . . . . . .8

H1 primary harness wire

connection guide . . . . . . . . . . . . . .9

primary harness wiring diagram .9

primary harness wiring guide . .10

H2 secondary harness wire

connection guide . . . . . . . . . . . . .13

secondary harness

wiring diagram . . . . . . . . . . . .13

secondary harness

wiring guide . . . . . . . . . . . . . .13

immobilizer harness wire

connection guide . . . . . . . . . . . . .14

immobilizer harness wiring . . .14

ultrasecure immobilizer . . . . . .15

immobilizer jumper setting . . .15

intellistart installation . . . . . . . . .16

obtaining constant 12V . . . . . .16

finding the 12V switched

ignition wire . . . . . . . . . . . . . .16

finding the starter wire . . . . . .17

finding a (+) brake light wire . .18

finding the accessory/heater

wire . . . . . . . . . . . . . . . . . . . . .18

finding the rpm input wire . . .18

How to find a tachometer wire

with your multimeter: . . . . . . .19

finding the wait-to-start bulb

wire for diesels . . . . . . . . . . . .19

H3 harness wire

connection guide . . . . . . . . . . . . .20

harness wiring diagram . . . . . .20

harness wiring guide . . . . . . . .20

H4 heavy gauge harness

wire connection guide . . . . . . . .22

heavy gauge harness

wiring diagram . . . . . . . . . . . .22

heavy gauge harness

wiring guide . . . . . . . . . . . . . .22

door lock connection guide . . . .24

door lock harness wiring guide 24

identifying the door lock

system . . . . . . . . . . . . . . . . . . .24

at the switch . . . . . . . . . . . . . .25

type A: positive-triggered,

relay-driven system . . . . . . . . .25

type B: negative-triggered,

relay-driven system . . . . . . . . .26

type C: reversing polarity

system . . . . . . . . . . . . . . . . . . .27

type D: after-market actuators .29

type E: electronically-activated

vacuum systems . . . . . . . . . . . .30

type F: one-wire system . . . . . .31

type G: positive (+) multiplex . .32

type H: negative (-) multiplex . .34

515C Self-Powered SmartSiren . .36

siren installation instructions . .36

peripheral plug-in harnesses . . .37

super bright blue led,

2-pin white plug . . . . . . . . . . .37

plain-view 2 valet . . . . . . . . . .37

mounting the receiver/antenna 38

arming/disarming diagnostics . . .39

arming . . . . . . . . . . . . . . . . . . .39

disarming . . . . . . . . . . . . . . . .39

system status chirps . . . . . . . . . . .39

remote siren silencing . . . . . . . . .39

multiple event total recall . . . . .40

table of zones . . . . . . . . . . . . . . .40

system features programming . .41

cliffnet wizard pro installation

software programming . . . . . .41

manual programming

instructions . . . . . . . . . . . . . . .41

contents

www.directed.com

user selectable features . . . . . .42

user selectable features

descriptions - column one . . . .43

user selectable features

descriptions - column two . . . .44

user selectable features descrip-

tions - column three . . . . . . . .45

installer selectable features . . .47

installer selectable features

descriptions - column one . . . .48

installer selectable features

descriptions - column two . . . .49

installer selectable features

descriptions - column three . . .50

programming notes . . . . . . . . .51

fact II - false alarm control

technology . . . . . . . . . . . . . . . . . .53

smart power up II . . . . . . . . . . . .54

remote control sensor disable . .54

auto-immobilization feature . . .54

auto-immobilization sequence .54

one-time valet feature . . . . . .55

blackjax feature . . . . . . . . . . . . . .55

blackjax activation sequence . .55

blackjax deactivation sequence 56

bypass blackjax temporarily

(if on in program grid) . . . . . . .56

blackjax off warning indicator .56

sensors . . . . . . . . . . . . . . . . . . . . .56

tilt/motion sensor . . . . . . . . . . .56

remote adjustable

proximity sensor . . . . . . . . . . .58

remote adjustable omnisensor .60

troubleshooting . . . . . . . . . . . . . .62

wiring reference section . . . . . . .63

control module

connector locations . . . . . . . . .63

H1 connector . . . . . . . . . . . . . .64

H4 connector . . . . . . . . . . . . . .67

H3 connector . . . . . . . . . . . . . .67

notes . . . . . . . . . . . . . . . . . . . . . . .69

warning! safety first

The following safety warnings must be observed at all times:

zDue to the complexity of this system, installation of this product must only be per-

formed by an authorized Clifford dealer.

zWhen properly installed, this system can start the vehicle via a command signal

from the remote control transmitter. Therefore, never operate the system in an

area that does not have adequate ventilation. The following precautions are the

sole responsibility of the user; however, authorized Clifford dealers should make

the following recommendations to all users of this system:

1. Never operate the system in an enclosed or partially enclosed area without

ventilation (such as a garage).

2. When parking in an enclosed or partially enclosed area or when having

the vehicle serviced, the remote start system must be disabled using the

installed toggle switch.

3. It is the user's sole responsibility to properly handle and keep out of reach

from children all remote control transmitters to assure that the system does

not unintentionally remote start the vehicle.

4. THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR

ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS

LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR

PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES

REMAIN CLOSED.

zUse of this product in a manner contrary to its intended mode of operation may

result in property damage, personal injury, or death. Except when performing

the Safety Check outlined in this installation guide, (1) Never remotely start the

vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the

keys in the ignition. The user will be responsible for having the neutral safety fea-

ture of the vehicle periodically checked, wherein the vehicle must not remotely

start while the car is in gear. This testing should be performed by an authorized

Clifford dealer in accordance with the Safety Check outlined in this product

installation guide. If the vehicle starts in gear, cease remote start operation imme-

diately and consult with the user to fix the problem immediately.

zAfter the remote start module has been installed, test the remote start module in

accordance with the Safety Check outlined in this installation guide. If the vehi-

cle starts when performing the Neutral Safety Shutdown Circuit test, the remote

start unit has not been properly installed. The remote start module must be

removed or properly reinstalled so that the vehicle does not start in gear. All

installations must be performed by an authorized Clifford dealer.

www.directed.com

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN

GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING

THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN

PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE

OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START

MODULE. CLIFFORD WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTAL-

LATION OR REINSTALLATION COSTS.

before beginning the installation

zPlease read this entire installation guide before beginning the installation. The

installation of this remote start system requires interfacing with many of the vehi-

cle’s systems. Many new vehicles use low-voltage or multiplexed systems that can

be damaged by low resistance testing devices, such as test lights and logic

probes (computer safe test lights). Test all circuits with a high quality digital multi-

meter before making connections.

zDo not disconnect the battery if the vehicle has an anti-theft-coded radio. If

equipped with an air bag, avoid disconnecting the battery if possible. Many

airbag systems will display a diagnostic code through their warning lights after

they lose power. Disconnecting the battery requires this code to be erased, which

can require a trip to the dealer.

zRemove the domelight fuse. This prevents accidentally draining the battery.

zRoll down a window to avoid being locked out of the car.

after the installation

zTest all functions. Refer to the "Using Your System" section of the Owner's Guide

when testing.

zComplete the vehicle Safety Check outlined in this manual prior to reassembly.

WWAARRNNIINNGG!!This system is intended for automatic

transmission, fuel-injected vehicles only. Installation in a

standard transmission vehicle maybe dangerous and is

contrary to its intended use.

what is included

transmitter configurations

www.directed.com

transmitter functions

This system uses computer-based code learning to learn the transmitter buttons. This

makes it possible to assign any transmitter button to any system function. The trans-

mitter initially comes programmed with standard configuration, but may also be cus-

tomized by an authorized dealer. The buttons in all of the instructions in this manual

correspond to a standard configuration transmitter.

standard configuration

Button

The arming, disarming, and panic function are controlled by this button.

Button

The trunk release or accessory output A is controlled by this button.

Button

Silent arm and disarm is controlled by this button.

Button

Remote start is controlled by this button.

Button, then Button

Accessory B output is controlled by these buttons.

Button, then Button

These buttons activate SmartWindows.

Button, then Button

Accessory C output is controlled by these buttons.

Button twice, then Button

These buttons active remote valet.

Button twice, then Button

These buttons disable the sensors.

Button twice, then Button

These buttons enter safe start mode for manual transmission vehicles and activate

Autostart mode.

Button three times, then Button

These buttons adjust the dual-zone omnisensor.

Button three times, then Button

These buttons adjust the dual-zone radar sensor.

H1 primary harness wire connection guide

primary harness wiring diagram

___

___ EMPTY Not Used

ORANGE Ground When Armed (500mA)

RED/WHITE (-) Accessory Output A (200mA)

BLACK/WHITE Dome Light Supervision Output 30

WHITE Light Flash Output

WHITE/RED Light Flash Input

BROWN Speaker Output 2

RED (+) 12V Constant

GREEN (-) Door Trigger Input - Zone 4

VIOLET (+) Door Trigger Input - Zone 4

BLUE (-) Trunk Trigger Input - Zone 5

WHITE/BLUE (-) Accessory B Output (200mA)

GREEN/WHITE (-) Normally Closed Input - Zone 6

EMPTY Not Used

GRAY (-) Hood Trigger Input Zone 6

BROWN Speaker Output 1

BLACK Ground

H1/1

H1/2

H1/3

H1/4

H1/5

H1/6

H1/7

H1/8

H1/9

H1/10

H1/11

H1/12

H1/13

H1/14

H1/15

H1/16

H1/17

H1/18

www.directed.com

primary harness wiring guide

This guide describes in detail the connection of each wire. Also included are possible appli-

cations of each wire. This system was designed with the ultimate in flexibility and security

in mind. Many of the wires have more than one possible function. Please read the instruc-

tions carefully to ensure a thorough understanding of this unit and how it operates.

h1/1 black ground

Connect the BLACK wire to a clean, paint-free sheet metal location (driver’s kick panel)

using a factory bolt that does NOT have any vehicle component grounds attached to

it. A screw should only be used in conjunction with a two-sided lock washer. Under

dash brackets and door sheet metal are not acceptable ground points. It is recom-

mended that all security components be grounded at the same location.

h1/2 and h1/11 brown speaker outputs

Connect the BROWN output wires to the BROWN wires of an optional 518C Neo Siren.

h1/3 gray (-) hood input zone 6

Connect this wire to the hood pin. If the hood is open when the alarm is armed, this

wire will trigger the siren. Use either this wire (preferred) or the wire from the

Intellistart module, but not both.

Autres manuels pour AVANTGUARD 5

Table des matières

Autres manuels Clifford Alarme de voiture

Clifford

Clifford Cyber 5 Manuel utilisateur

Clifford

Clifford 590.4X Manuel utilisateur

Clifford

Clifford IntelliGuard 7000 Manuel utilisateur

Clifford

Clifford Virtual Key 2UK Manuel utilisateur

Clifford

Clifford G4 System Series Manuel utilisateur

Clifford

Clifford 4806X Manuel utilisateur

Clifford

Clifford Matrix 1 Manuel utilisateur

Clifford

Clifford 10.5X Manuel utilisateur

Clifford

Clifford IntelliGuard Millennia Manuel utilisateur

Clifford

Clifford 20 Manuel utilisateur

Clifford

Clifford System II Manuel utilisateur

Clifford

Clifford AvantGuard 5.1 Manuel utilisateur

Clifford

Clifford intelliguard 700 Manuel utilisateur

Clifford

Clifford BlackJax 5 Manuel utilisateur

Clifford

Clifford 562C Manuel utilisateur

Clifford

Clifford AvantGuard 2 Manuel utilisateur

Clifford

Clifford IntelliPage IntelliPage System Car Alarm Manuel utilisateur

Clifford

Clifford SE 2020 Special Edition Manuel utilisateur

Clifford

Clifford Concept 450 Manuel utilisateur

Clifford

Clifford 980074 SERIES 11CX Manuel utilisateur

Clifford

Clifford Ultramax XL2500 Manuel utilisateur

Clifford

Clifford Polaris II Manuel utilisateur

Clifford

Clifford 510.4X Manuel utilisateur

Clifford

Clifford Advantage Manuel utilisateur

Manuels Alarme de voiture populaires d'autres marques

Ultra Start

Ultra Start 2500M SERIES Manuel utilisateur

Ultra Start

Ultra Start 650 Series Manuel utilisateur

Audiovox

Audiovox Prestige Platinum+ APS-511C Manuel utilisateur

Sparkrite

Sparkrite SRA8 Manuel utilisateur

Viper

Viper 4708V Manuel utilisateur

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manuel

Falcon

Falcon Predator XL3 Guide de l'utilisateur

Audiovox

Audiovox Auto Security XR91 Mode d'emploi

CrimeStopper

CrimeStopper CS-8717 Guide de démarrage rapide

Ultra Start

Ultra Start 450 SERIES Manuel utilisateur

Scytek electronic

Scytek electronic Vectra X3 Manuel utilisateur

Excalibur

Excalibur AL-1860-EDPB Manuel utilisateur

Gemini

Gemini 7057 Manuel utilisateur

FlashLogic

FlashLogic FLRSBA PRESTIGE Manuel utilisateur

Magicar

Magicar FAI-440 Manuel utilisateur

Viper

Viper 560XV Manuel utilisateur

SECO-LARM

SECO-LARM 300C Manuel utilisateur

Python

Python 660XP Manuel utilisateur