Clic Cardinal WD-02.2 Manuel utilisateur

Rev. G

CARDINAL CLiC WD-02.2

GLASS CONTROLLER

INSTALLATION MANUAL

Page 2 of 15

Rev. G

PRECAUTIONS

IMPORTANT SAFETY INSTRUCTIONS

Read Instructions: Read all safety and operating instructions before using the device.

Retain Instructions: Keep safety and operating instructions for future reference.

Heed Warnings: Adhere to all warnings on the device and in the operating instructions.

Follow Instructions: Follow operating instructions and installation instructions. Failure to follow these instructions

may damage the product or void the product warranty.

Heat: Keep the device away from heat sources such as radiators, heat registers, stoves, etc.

Power Sources: Connect only to the power supply that was included with the device.

Power Cord Protection: Route power supply cords so that they are not likely to be stepped on or pinched by items

placed on or against them. Paying particular attention to the cords at plugs, receptacles, and at the point at which

they connect to the device.

Water and Moisture: Do not use the device near water; for example, near a sink, in a wet basement, near a

swimming pool, near an open window, in a damp mechanical room, etc.

Object and Liquid Entry: Do not allow objects to fall or liquids to be spilled into the enclosure through openings.

Indoor Use Only: The device should be installed and used indoors only. Do not use the device outdoors.

Servicing: There are no user serviceable parts inside of the device. Do not attempt to open the enclosure or

perform any service beyond that described in the operating instructions. Refer all other service needs to qualified

service personnel.

Damage Requiring Service: The device should be serviced by qualified service personnel when:

•Objects have fallen or liquid has been spilled into the device.

•The power supply cord or the plug has been damaged.

•The device does not appear to operate normally or exhibits a marked change in performance.

•The device has been dropped or the enclosure has been damaged.

WARNING!

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,DO NOT EXPOSE THE DEVICE TO RAIN OR MOISTURE.

SAVE THESE INSTRUCTIONS

Page 3 of 15

Rev. G

DISCLAIMER

FCC INFORMATION TO USERS

FCC Information to Users

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 Subpart B of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a commercial, industrial, or business installation. This equipment generates, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

•Reorient or relocate the receiving antenna

•Increase the separation between the equipment and receiver

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

•Consult the dealer or an experienced radio/TV technician for help

Warning: Changes or modifications not expressly approved by Cardinal IG Company could void the user’s authority

to operate the equipment.

Warning: This unit is tested to FCC Part 15 Subpart B and, as such, is not intended for use in a residential

environment. Any installation within a residential environment is considered outside of the intended use for this

device.

 
Page 4 of 15 
Rev. G 
CONTENTS 
TABLE OF CONTENTS 
Important Safety Instructions........................................................................................................................... 2 
FCC Information to Users..................................................................................................................................3 
Overview......................................................................................................................................................... 5 
Important Notes ..............................................................................................................................................5 
Compatability ..................................................................................................................................................5 
What’s In The Box? ..........................................................................................................................................5 
Unpacking and Inspection ................................................................................................................................6 
Controller Layout .............................................................................................................................................7 
Mounting ........................................................................................................................................................8 
Power..............................................................................................................................................................8 
Wire Connection Terminals ..............................................................................................................................9 
Site Wiring and Preparation ........................................................................................................................... 10 
System Layout Examples ................................................................................................................................ 11 
Specifications................................................................................................................................................. 13 
Common Symptoms and Solutions ................................................................................................................. 14 
Conctacting Us............................................................................................................................................... 15 
 
 
 

Page 5 of 15

Rev. G

CHAPTER 1 - INTRODUCTION

OVERVIEW

This guide pertains to the Cardinal CLiC WD-02.2 Glass Controller. This device and the associated CLiC Glass Panel

have been designed as a Class-3 system. The purpose of this document is to provide guidance on how to setup and

install the device into a commercial, industrial, or business environment. This document includes installation site

requirements, wiring requirements, system connection instructions, and basic troubleshooting.

IMPORTANT NOTES

Please read these important notes about the CLiC WD-02.2 Glass Controller:

•The WD-02.2 must be installed within an appropriate NEMA enclosure placed in a dry ventilated area that

maintains a normal room temperature (between 60°F to 90°F).

•Avoid installing the WD-02.2 in a location where it will have exposure to prolonged direct sunlight.

•Do not let the WD-02.2 get wet. It should not be handled with wet hands or placed in an area where it

could get wet.

•Only use the power supply that is included with the WD-02.2. The included power supply is a 100-watt UL

listed 1310 power supply with a Class-2 power limited output. Using the wrong type of power supply may

result in damage.

•Do not disassemble the device. Service of the WD-02.2 should be performed by authorized personnel

only.

COMPATABILITY

This device is specifically designed for use only with CLiC Glass panels. Use this device only for its intended use as

described in these instructions. Do not use attachments not recommended by the manufacturer. Connecting this

device to load types other than CLiC Glass panels may damage the device or the unauthorized loads. Cardinal IG

Company will not be responsible for any damage caused by inappropriate usage of this device.

WHAT’S IN THE BOX?

The following items are included with the CLiC WD-02.2 Glass Controller:

•Installation Manual

•Power Supply: 24v DC 100-watt UL-1310 Class-2

oWith 6-pin locking spring terminal connector (female) pre-connected

•Paper mounting templates

•Rubber Feet

•Cardinal CLiC screwdriver with magnetized handle

Page 6 of 15

Rev. G

UNPACKING AND INSPECTION

After opening the WD-02.2 package, save all of the packaging material in case you ever need to ship the unit.

Thoroughly inspect and make sure the devices are in good condition and there is no visible damage. If you have

any doubt about the product’s integrity, please contact your reseller or an authorized support center immediately.

Page 7 of 15

Rev. G

CHAPTER 2 - FEATURES

CONTROLLER LAYOUT

NOTE: The WD-02.2 must be installed within an appropriate NEMA enclosure.

NOTE: Shielded wire must be used for all connections to the WD-02.2. The shield shall be terminated on the WD-02.2

end of the wire only and shall be connected to either of the ‘Ground’ terminals as labeled above. The shield at the

CLiC Glass end and the Switching Device end can be cut where the cable jacket is removed.

Page 8 of 15

Rev. G

CHAPTER 3 – INSTALLATION

MOUNTING

The CLiC WD-02.2 Glass Controller must be installed within an appropriate NEMA enclosure. The device can be

mounted (details below) within the enclosure or free standing. The WD-02.2 does not need to be mounted near

the CLiC Glass panel. Both the CLiC Glass powered outputs and the dry contact inputs can be extended up to 100

meters (328 feet).

Mounting Pattern Drawings

POWER

DO NOT APPLY POWER PRIOR TO COMPLETING ALL WIRING CONNECTIONS AND TERMINATIONS.

ALL PROTECTIVE FILMS MUST BE REMOVED PRIOR TO CONNECTING THE WD-02.2 GLASS CONTROLLER

The included power supply (A/C Adapter) should be connected to the ‘24 VDC in’ and ‘Ground’ input terminals on

the WD-02.2. The terminal connector will be pre-attached to the power supply. The CLiC WD-02.2 will be powered

on and begin functioning upon applying power.

Use only the supplied power supply to power the WD-02.2. Do not connect more than one WD-02.2 to a power

supply.

WD-02.2

Page 9 of 15

Rev. G

WIRE CONNECTION TERMINALS

NOTE: Shielded wire must be used for all connections to the WD-02.2. The shield shall be terminated on the WD-02.2

end only and shall be connected to the ‘Ground’ terminals as dictated below.

•Terminal: +24 VDC In

Positive power supply connection. This is used to power the device.

•Terminal: Ground (-24 VDC In)

Common ground connection. Use this ground reference for power supply ground connection, trigger

ground connection, and wire shield ground connections.

•Terminal: Dry Contact In

The WD-02.2 has a dry contact input that is used to allow external devices to control the state of the CLiC

Glass panel. The triggering device shall use a ground referenced switch or relay type output. The CLiC

Glass panel will go to the clear state when the contact closure is closed. The CLiC Glass panel will go to the

privacy state when the contact closure is open.

•Terminal: Ground

Common ground connection. Use this ground reference for power supply ground connection, trigger

ground connection, and wire shield ground connections.

•Terminal: Glass Out A

This is the power signal output used for driving the CLiC Glass panel. Both Glass Out A and Glass Out B

must be connected to the CLiC Glass panel. Glass Out A and Glass Out B can be connected to either corner

of the CLiC Glass panel. Shorting the outputs will damage the WD-02.2 and should be avoided.

NOTE: Only connect a single CLiC Glass panel. Not to be used with multiple CLiC Glass panels.

•Terminal: Glass Out B

This is the power signal output used for driving the CLiC Glass panel. Both Glass Out A and Glass Out B

must be connected to the CLiC Glass panel. Glass Out A and Glass Out B can be connected to either corner

of the CLiC Glass panel. Shorting the outputs will damage the WD-02.2 and should be avoided.

NOTE: Only connect a single CLiC Glass panel. Not to be used with multiple CLiC Glass panels.

•Circuit Breaker

The WD-02.2 Glass Controller is equipped with a resettable circuit breaker to help protect against

accidental miswiring of the Glass Outputs. The circuit breaker will trip to protect the WD-02.2 in the event

that the Glass Output wiring is mis-wired, shorted together, or the line was cut during installation. In this

event the white plastic button will pop-out and the unit can reset by pushing the button back in. Make

sure to correct the wiring problem prior to resetting the circuit breaker.

Page 10 of 15

Rev. G

INSTALLATION AND OPERATION

SITE WIRING AND PREPARATION

Wiring from the WD-02.2 to the CLiC Glass panel should be run prior to the CLiC Glass panel installation. All wiring

must be performed in accordance with the applicable building codes and electrical wiring requirements as denoted

for Class 3 systems of the National Electric Code (NEC). All wiring should be completed by a qualified and

experienced technician.

Placement: The WD-02.2 should be installed within an appropriate NEMA enclosure in a accessible area within

sufficient distance to plug the power supply into a standard 120vac outlet. The WD-02.2 and the power supply are

both mountable if desired. Please allow adequate space for ventilation and heat dissipation around the devices.

NOTE: IN THE EVENT THAT THESE DEVICES ARE INSTALLED WITHIN AN AIR-EXCHANGE SPACE (PLENUM AIRWAY)THEY

SHALL BE MOUNTED WITHIN AN APPROPRIATE CERTIFIED PLENUM-SAFE ENCLOSURE OF MINIMUM SIZE GREATER THAN

273 X 100 X 138MM.

Wire Type and Connections

Shielded two-conductor wire must be used for all wire connections on the WD-02.2 Glass Controller. This is

important to maintain FCC compliance and to minimize the chance for electrical interference. IMPORTANT:When

completing the terminal connections, the shield of each wire run must be terminated to the ‘Ground’ terminals on

the WD-02.2 and left unconnected at the CLiC Glass panel and at the trigger switch or relay devices.

Wire Size and Maximum Length

The shielded wire utilized for connections on the WD-02.2 shall be a minimum of 18 AWG. It is important that the

correct gauge wire is used to assure the correct voltage and signal reaches the CLiC Glass panel. The maximum

wire distance between the WD-02.2 and the CLiC Glass panel is 100 meters (328 feet).

Table des matières

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur