Clearlight SANCTUARY Manuel utilisateur
CLEARLIGHT SANCTUARY
FULL SPECTRUM SAUNAS
OWNER’S MANUAL
Superior Quality and Service
Congratulations on your purchase of a Clearlight Infrared Sauna.
We are condent that you will enjoy the many benets of your sauna for years to come.
Please read this manual before using your Sauna for the rst time.
Please keep this manual for future reference.
Table of Contents
Welcome ------------------------------------------ 03
Installation ----------------------------------------- 04
01 | SANCTUARY 1 --------------------------------- 05
02 | SANCTUARY 2 --------------------------------- 19
03 | SANCTUARY 3 --------------------------------- 33
04 | SANCTUARY Y AND SANCTUARY RETREAT ----------- 47
05 | SANCTUARY C --------------------------------- 65
Enjoying Your Sauna---------------------------------- 80
Using Your Sauna Control Panel ------------------------- 81
Tips for Use ---------------------------------------- 85
Safety Instructions ----------------------------------- 87
Warranty ------------------------------------------ 89
Important Safeguards--------------------------------- 95
* The information contained in this manual is subject to change without notice.
4
Installation
Choosing a location
Place your sauna on a dry and level surface for best results. Garage, basement, attic, playroom, bedroom, or
garden house are just a few of the possible locations for your sauna.
Your sauna’s natural cedar or basswood exterior will beautifully compliment any location.
Outside, place the sauna on a deck or concrete pavers, available at your local building supply store, to protect
it from moisture in the ground which can wick up through the wooden feet. Outside installation also requires
our optional canvas cover.
Installation requirements for your sauna are as follows:
1. Your Clearlight® sauna is a self-contained and freestanding unit. It should not be built into any structure
without prior authorization.
2. Please maintain a minimum of 4-inch clearance on all sides of the unit to allow air to circulate while giving
access for the power cord..
Cleaning and maintenance
1. Before using your sauna for the rst time, clean the inside of the sauna with a damp cloth.
Use your favorite furniture polish on the exterior.
2. Place a towel on the oor and bench to absorb any perspiration. Wash these often to maintain a clean and
pleasant environment inside your sauna.
3. Perspiration may darken the wood over time. This can be removed by a light sanding with ne grit
sandpaper.
Please be careful when carrying and installing the glass pieces to avoid breakage. Make certain the glass is securely fastened
during installation before letting go of any individual piece that could break.
SANCTUARY 1
5
SANCTUARY 101
Packaging - - - - - - - - - - - - - - - - - - - - - - - 06
Assembly Instructions - - - - - - - - - - - - - - - - - 07
6
SANCTUARY 1
.
Packaging
Box 1 of 4 Box 2 of 4 Box 3 of 4 Box 4 of 4
1. Floor Panel 1. Left Side Wall 1. Front Wall Glass 1. Front Heaters
2. Ceiling Panel 2. Right Side Wall 2. Back Wall
3. Accessories 3. Bench & Bench Support
4. Installation Manual
CONTENTS OF BOXES
ACCESSORY BOX CONTENTS
Door Handle
Wall Security Brackets
(located installed in wall)
Glass Security
Brackets (2 sets)
Wood piece
(2 pieces)
Front Heater
Mounting Screws
(4 sets)
SANCTUARY 1
7
Assembly Instructions
Assembly of the sauna requires two adults to complete. Please read the instructions thoroughly before and
during assembly to ensure proper installation of the unit. If you encounter any problems or have questions
during assembly, please feel free to call our Customer Service department at 1-800-798-1779 or
+1-510-601-1775.
When determining a location for your sauna, please keep in mind the following:
1. The main power cord on the sauna must be easily accessible.
2. The location must be dry and level.
3. Panels should be installed in the following order:
1) Floor 4) Right Side Wall 7) Wood Roof
2) Back Wall 5) Under Bench Support 8) Glass Roof
3) Left Side Wall 6) Bench 9) Front Wall Glass
1. Place the bottom oor panel on the ground
near the location you will using the sauna.
Make sure the front of the oor is in the
desired location of the door. The two oor
receptacles and the door magnet indicate
the front of the sauna.
1. Place the back panel on the oor panel by placing
it in the groove of the oor panel.
1 - LOCATION OF SAUNA & INSTALLATION ORDER
2 - PLACING FLOOR PANEL 3 - CONNECTING THE BACK PANEL
TO THE FLOOR PANEL
8
SANCTUARY 1
Assembly Instructions Cont’d
The side wall panels connect to the back wall with the installed locking brackets. There are mating brackets
on the side of each panel.
1. Place the left side wall in the slot in the
oor. Lift the side wall up about 4” (10cm)
higher than the backwall panel (See Picture
1).
2. Place the side wall panel against the back
wall (See Picture 2), then slide down side
wall panel until the two panels are equal
height. (See Picture 3).
3. If the panels are not equal height or
there is an obvious gap between the two
panels, this means they are not propery
attached and you should try again.
4. Repeat the steps above for the right side
wall panel.
4 - CONNECTING SIDE WALLS
Picture 1 Picture 2 Picture 3
Right Side Wall InstalledLeft Side Wall Installed
If the panels still seem too tight to
come down all the way, try backing o
the bracket screws by one half turn
with a Phillips head screwdriver on the
female bracket.
SANCTUARY 1
9
Assembly Instructions Cont’d
Slide down the bench heater panel by lining up its sides with the vertical guides on the left and right side
wall panel.
1. Be careful not to scratch the side panels when positioning the heater panel.
2. Push the bench heater panel all the way down until it is touching the oor panel and securely in
place.
5 - INSTALLING UNDER BENCH SUPPORT
Vertical bench heater
panel guides are found
on the side panels.
Heater must be
facing outward
10
SANCTUARY 1
Assembly Instructions Cont’d
Plug in the connectors under the bench as follows:
Left Side Wall:
1. Locate the short cable coming out of the oor with a single black and white cable and a single green
cable. This cable is comes threaded through the hole of the white cable cover.
2. Locate the cable coming out of the under bench support. Feed this cable through the open hole in the
bottom of the white cable cover.
3. Connect these cable to the cables coming out of the white box on the left side wall. You can connect
the black and white cables from the oor and underbench support to any black and white cable coming
out of the box as long as you match cable colors. You can connect the green cables to any of the green
cables coming out of the box as long as you match cable colors.
4. Screw on the cover to cover the wires on the side wall.
Back Wall:
1. Locate the longer cable coming out of the oor that feeds
through a hole in the white cover.
Connect the longer cable coming out of the oor to the like
connector in the cables coming out of the white box on the
back wall. Connect the cable with two wires to the cable
with two wires in the back all. Connect the cable with four
wires to the cable with four wires coming out of the back
wall.
2. Screw on the cover to cover the wires on the back wall.
3. The additional plate on the back wall is used to connect
the Vibration Resonance Therapy (VRT) to your sauna. If
you purchased the VRT, follow the installation instructions
included with the VRT.
6 - CONNECT HEATER CONNECTION UNDER BENCH
You can plug any male connector to any female one as long as
the colors match.
SANCTUARY 1
11
Assembly Instructions Cont’d
Install the bench panel by sliding it over the horizontal bench guides on the side panels. Be careful not to
scratch the adjacent panels when sliding in the bench.
Push the bench all the way in until it touches the back panel and is securely in place.
The bench is reversible. One side is ergonomic and one side is at. You can reverse the bench after the
sauna installation is nished. Be sure that the bench is pushed all the way back until it slides under the
heater guard to secure the bench in place.
Optional: After the bench is installed, you
can slide in the included wood pieces
to prevent the bench from sliding left to
right. One piece can be placed on each
side next to the bench. If you decide to ip
the reversible bench over, please remove
the wood pieces rst.
7 - INSTALLING THE BENCH
LLEEFFTT
TTOOPP
BBOOTTTTOOMM
FFRROONNTT
BBLLAACCKK
LEFT
TOP
BOTTOM
FRONT
BLACK
1. Set the wood portion of
the roof on the back roof
guide. Besure to slide the
roof back against the back
wall.
8 - INSTALLING WOOD PORTION OF ROOF
Ce manuel convient aux modèles suivants
6
Table des matières
Autres manuels Clearlight Produits de plomberie
