Clear One MAX IP Response Point Manuel de service

MAX™ IP Response Point™

ADMINISTRATOR’S GUIDE

document title

ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION FROM CLEARONE.

CLEARONE RESERVES SPECIFIC PRIVILEGES. INFORMATION IN THIS DOCUMENT IS

SUBJECT TO CHANGE WITHOUT NOTICE.

tecHnicAl SuPPoRt

Telephone 1.800.283.5936

1.801.974.3760

Fax 1.801.977.0087

Email [email protected]

Web www.clearone.com

Chapter 1: Product Overview 1

PRODUCT OVERVIEW 1

SERVICE AND SUPPORT 1

Important safety information 2

Unpack 3

System Requirements 3

Microsoft Response Point Software Download 3

Chapter 2: Installation 4

Connecting your conference phone 4

Connecting Additional MAX IP Response Point

Phones 4

Manually assigning an IP address 5

Manually provisioning your MAX IP Response

Point phone 5

Chapter 3: Configuration of the MAX

IP Response Point Phone 5

Web Portal Screens 6

Chapter 4: User Options 10

PROGRAMMING OPTIONS 10

To Change Dynamic Host Configuration Protocol

(DHCP) 10

To Change Host IP Address 10

To Change Subnet Mask 10

To Program a Default Gateway IP Address 11

To Program the Automatic Gain Control (AGC)

and Automatic Level Control (ALC) Settings 11

To Restore Factory Defaults 11

Chapter 5: Response Point Configu-

ration 12

MAX IP Response Point software 12

To Connect a New Phone or Device: 12

Installing Response Point Administrator 12

Response Point Administrator 13

Adding a New Phone 13

Chapter 6: Troubleshooting 16

Troubleshooting 16

MAX IP Response Point Troubleshooting 16

Response Point Troubleshooting 17

Customer Service and Support 21

ClearOne on the Web 21

North America (Worldwide Headquarters) 21

Latin America 21

EMEA 21

Asia-Pacific/Japan/Oceania 21

Product registration 21

WARRANTY INFORMATION 21

Appendix : A - Specifications 23

Appendix : B - Tools and Resources 24

Assessment checklist 24

Deployment checklist 26

Appendix : C - Compliance 28

1 Technical Services: 800-283-5936

CHAPTER 1: PRODUCT OVERVIEW

PRODUCT OVERVIEW

Thank you for purchasing the ClearOne MAX™ IP Response Point™ expandable conferencing phone. MAX IP

Response Point provides premium, full-duplex audio to small conference rooms as a single unit and to larger rooms

as an expanded system. Up to four MAX IP Response Point units can be linked, expanding not only microphone

coverage but loudspeaker coverage and control access as well. This creates even distribution of sound for a more

natural communications experience. Setting up the MAX IP Response Point conferencing phone requires only three

connections: power, network, and the base unit to the conferencing phone. And, the familiar keypad design ensures

that you will be comfortable using the phone, reducing the need for training, and support.

EXPANDABLE• . MAX IP Response Point is ideal for conference rooms and provides complete microphone

and loudspeaker coverage and easy access to controls.

SUPERIOR AUDIO• . The clear, full sound of the MAX IP Response Point facilitates more natural interaction

among participants.

ONE-TOUCH CONFERENCING• . Single-button access to the Response Point voice-activate phone system.

EASY TO USE• . The intuitive, user-friendly controls are simple to operate.

SERVICE AND SUPPORT

If you need additional information on how to set up or operate your MAX IP Response Point conferencing phone,

please contact us. We welcome and encourage your comments so we can continue to improve our products and

better meet your needs.

TECHNICAL SUPPORT

Telephone: 1.800.283.5936(USA) or 1.801.974.3760

Fax: 1.801.977.0087

E-mail: [email protected]

Web site: www.clearone.com

SALES AND CUSTOMER SERVICE

Telephone: 1.800.945.7730 (USA) or 1.801.975.7200

Fax: 1.800.933.5107 (USA) or 1.801.977.0087

E-mail: [email protected]

PRODUCT RETURNS

All product returns require a return authorization (RA) number. Please contact ClearOne Technical Support before

attempting to return your product. Please be sure to return all the items that shipped with your product.

2 Technical Services: 800-283-5936

IMPORTANT SAFETY INFORMATION

Read all safety information before using this product.

Read and understand all instructions.•

Follow all warnings and instructions marked on the product.•

Unplug this product from the wall outlet before cleaning. Use a damp cloth for cleaning. Do not use liquid•

cleaners or aerosol cleaners.

Do not use this product near water, including bathtubs, sinks, or near a swimming pool.•

Do not place this product on an unstable cart, stand, or table.•

Slots and openings in the back, bottom, and/or sides of the product are provided for ventilation. To prevent•

overheating, these openings must not be blocked or covered.

This product should never be placed near or over a radiator or heat register. This product should not be used•

in built-in installations unless proper ventilation is provided.

This product should be operated only from the type of power source indicated on the marking label. If you•

are not sure of the type of power supply in your location, consult your dealer or local power company.

Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.•

Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage•

points or short out parts that could result in fire or electric shock.

Never spill liquids on the product.•

To reduce the risk of electric shock, do not disassemble this product. Opening or removing covers may•

expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock during

subsequent use.

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following•

conditions:

When the power supply cord or plug is damaged or frayed.»

If liquid has been spilled into the product.»

If the product does not operate normally according to the operating instructions.»

If the product has been dropped or damaged.»

If the product exhibits a distinct change in performance.»

Do not use this product during an electrical storm. There is a remote risk of electric shock from lightning.•

Do not use this product near intensive care medical equipment or by persons with pacemakers.•

This product can interfere with electrical equipment such as tape recorders, TV sets, radios, computers and•

microwave ovens if placed in close proximity.

Save These Instructions

3 Technical Services: 800-283-5936

UNPACK

Place the conferencing pod and base unit on a level surface. Ensure you have received all items shown in figure 1.

Use the pack-out diagrams below to verify that you received all components for your MAX product.

Note: Inspect your shipment carefully for obvious signs of damage. ClearOne is not responsible for

product damage incurred during shipment. You must make claims directly with the carrier. If the shipment

appears damaged, retain the original boxes and packing material and contact your carrier immediately.

SYSTEM REQUIREMENTS

System requirements for Microsoft® Response Point™ can be found at:

http://www.microsoft.com/responsepoint/resources-datasheet.asp• x

Microsoft Response Point Software Download

Microsoft Response Point SP1 is available as a free download at the following location:

http://www.microsoft.com/responsepoint/features-software-SP1-download.asp• x

Figure 1.1 MAX IP Response Point parts

4 Technical Services: 800-283-5936

CHAPTER 2: INSTALLATION

CONNECTING YOUR CONFERENCE PHONE

Connect the Connection cable from the Link Out jack on the base unit to the Link In jack on the conferencing pod

(see figure 2.1).

Warning: DO NOT plug a laptop or PC into the Link Out jack on the base unit or conferencing pod as

severe electrical damage could occur.

Connect the base unit to the Ethernet jack using the Ethernet cable.

Connect the power cord to the base unit and plug it directly into an electrical outlet.

CONNECTING ADDITIONAL MAX IP RESPONSE POINT PHONES

Connect the 12’ Connection cable to the Link Out jack on the first phone and to the Link In jack on the second

phone (see figure 2.2).

12' Connection cable

From Link Out

To Link In

To Link Out on Base Unit

25' Connection cable

Continue linking additional MAX IP Response Point phones in the same fashion. A total of four units may be

connected.

Figure 2.1 Connecting the MAX IP Response Point

Figure 2.2 Connecting additional units

5 Technical Services: 800-283-5936

CHAPTER 3: CONFIGURATION OF THE MAX IP RESPONSE

POINT PHONE

MANUALLY ASSIGNING AN IP ADDRESS

If DHCP is disabled or you wish to assign a static IP address, perform the following steps:

Press and hold the1. REDIAL/PROG key until the program icon appears on the LCD screen.

Note: If a key is not pressed within 30 seconds of entering program mode, the MAX IP Response

Point phone will beep and return to normal operation mode.

Press the2. 2key. The default IP address is displayed on the LCD screen. If this address was obtained from

DHCP, then you can use it to access the web interface. If you cannot access the web interface using this

address, then you need to either configure DHCP as explained above so that the IP address can be obtained

automatically, or you must manually enter a static IP address. Continue with step 3 to manually enter a static

IP address for the MAX IP Response Point phone.

Press the3. 1key. The current DHCP setting is displayed on the LCD screen. A “1” indicates that DHCP

mode is enabled; a “0” indicates that DHCP mode is disabled.

If “0” is the current setting, then continue with step 8, otherwise continue with step 5.4.

Press the5. REDIAL/PROG key. The current DHCP mode “1” will flash on the LCD screen.

Press the6. 0key. The new DHCP mode “0” will flash on the LCD screen.

Press the7. REDIAL/PROG key. DHCP mode is disabled.

Press the8. 2key. The current IP address (such as 0.0.0.0) will be displayed on the LCD screen.

Press the9. REDIAL/PROG key. The current IP address will flash on the LCD screen.

Press the10. CLEAR key. The current IP address will be deleted one character at a time.

Using the number keys, enter the static IP address. Use the * key to enter the decimal separators in the11.

IP address.

Press the12. REDIAL/PROG key. The new static IP address is activated in the MAX IP Response Point phone.

Press the13. 3key and repeat steps 9-12 above to set the subnet mask, then continue with step 14.

Press the14. REDIAL/PROG key. The MAX IP Response Point phone will reboot.

MANUALLY PROVISIONING YOUR MAX IP RESPONSE POINT PHONE

The easiest way to manually provision your MAX IP Response Point phone is through the web interface. To access

the web interface, perform the following steps:

Press and hold the1. REDIAL/PROG key until the program icon appears on the LCD screen.

Press the 2 key. The phone’s IP address will be displayed on the LCD screen.2.

6 Technical Services: 800-283-5936

Make note of the IP address and press the3. CLEAR key. The phone will exit Program mode.

Start Internet Explorer.4.

Note: Only Internet Explorer, release 6.0 or later with Java 1.5 or later installed, is supported by the MAX IP

Response Point phone.

Enter the phone’s IP address into the Internet Explorer address field and press the5. ENTER key on your

computer’s keyboard. (You can also enter the DNS name or the phone’s name on the network in order to get

to the web interface login screen.)

The MAX IP Response Point’s web portal will appear, displaying the Device Information screen.6.

Web Portal Screens

The following sections display each of the screens included in the MAX IP Response Point web portal and describe

all of the settings that can be modified through each of the screens.

Device Information screen

The Device Information screen (see figure 3.2) displays all of the system information for your MAX IP Response

Point phone. The information fields are self-explanatory. Please note that the last four digits of the MAC address

are used as an identifier in the system name. By default, the system name is in the format of MAX1AV- followed by

the last four digits of the MAC address. The MAC address is a unique address in hexadecial format that can also

be found on the label attached to the back of your MAX IP Response Point base unit. This screen (and all other

screens) also includes a link to the Registration page in order to register your MAX IP Response Point phone with

ClearOne. Simply click the Registration link to go there.

Figure 3.2 Device Information screen

Table des matières

Autres manuels Clear One Système de conférence

Clear One

Clear One COLLABORATE Versa Pro 50 Manuel utilisateur

Clear One

Clear One Aura VERSA Pro CT Manuel utilisateur

Clear One

Clear One CONVERGE Pro 2 (CP2) Series Manuel utilisateur

Clear One

Clear One XAP 400 Manuel utilisateur

Clear One

Clear One CONVERGE Huddle Manuel utilisateur

Clear One

Clear One XAP 80 Manuel utilisateur

Clear One

Clear One CONVERGE PRO 2 Manuel utilisateur

Clear One

Clear One XAP 400 Manuel utilisateur

Clear One

Clear One COLLABORATE Pro 300 Manuel utilisateur

Clear One

Clear One COLLABORATE LIVE 200 Manuel utilisateur

Clear One

Clear One Aura VERSA PRO 50 Manuel utilisateur

Clear One

Clear One AP400 Manuel utilisateur

Clear One

Clear One COLLABORATE Pro 300 Manuel utilisateur

Clear One

Clear One COLLABORATE Versa Room CT Manuel utilisateur

Clear One

Clear One UNITE 160 Manuel utilisateur

Clear One

Clear One Chat 50 Manuel utilisateur

Clear One

Clear One Converge Pro Manuel utilisateur

Clear One

Clear One magicbox aavelin Manuel utilisateur

Clear One

Clear One COLLABORATE ROOM PRO Manuel utilisateur

Clear One

Clear One Converge 560 Manuel utilisateur

Clear One

Clear One INTERACT AT-OC Manuel utilisateur

Clear One

Clear One ClearOne RAV 600 Manuel utilisateur

Clear One

Clear One COLLABORATE Live 600 Manuel utilisateur

Clear One

Clear One ClearOne RAV 600 Manuel utilisateur

Manuels Système de conférence populaires d'autres marques

Kramer

Kramer VIA GO Manuel utilisateur

AVT

AVT MAGIC AC1 Go Manuel utilisateur

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Manuel utilisateur

Sony

Sony PCS-I150 Manuel utilisateur

Middle Atlantic Products

Middle Atlantic Products VTC Series Manuel utilisateur

Prentke Romich Company

Prentke Romich Company Vanguard Plus Mode d’emploi

Speakerbus

Speakerbus iD 712 Manuel utilisateur

Trelleborg

Trelleborg SafePilot CAT PRO Manuel utilisateur

Sennheiser

Sennheiser ADN Manuel utilisateur

ADTRAN

ADTRAN NetVanta 7100 Manuel utilisateur

AINA

AINA PTT Voice Responder Manuel utilisateur

Yamaha

Yamaha ProjectPhone PJP-100H Manuel utilisateur

vissonic

vissonic VLI Series Manuel utilisateur

Panasonic

Panasonic KX-VC500 Manuel utilisateur

Poly

Poly Trio 8300 Manuel utilisateur

Crestron

Crestron Mercury CCS-UCA-SMK Dessin dimensionnel

Inmarsat

Inmarsat mini M Manuel utilisateur

Tenveo

Tenveo ALL-IN-ONE Manuel utilisateur