Claudgen HE7010RF Manuel

44000070 Iss 04

Consort Equipment Products Ltd

Registered Office: Thornton Industrial Estate

Milford Haven, Pembrokeshire, S 73 2RT

Tel: 01646 692172 Fax: 01646 695195

BS EN ISO 9001 Registered Company No FM12671

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR

He t-Zone Fan Heater

FOR WIRELESS CONTROLS

C t logue Numbers: HE7010RF 3 kW 230/240V

PLEASE RETAIN THIS LEAFLET FOR FUTURE MAINTENANCE

MODEL

Heat-Zone is a quiet Fan Heater designed for Commercial and

Industrial situations, and is suitable for mounting on the wall.

The Heat-Zone incorporates a tangential flow fan and the unit is

designed to operate in free air conditions. It is important that

there should be no restriction on the free flow of air through the

unit. When installed the top of the heater case should be a

minimum of 200mm from the ceiling.

MOUNTING

The normal mounting height is 2.3m above the floor, although

this will depend to some extent on the situation.

The heater can be positioned to blow air at any angle, from

horizontal to vertically downwards, subject to the conditions

mentioned below. It is suggested that an angle of 45

is a

convenient starting point when setting up the unit.

It must always be installed with the axis of the motor horizontal.

Failure to ensure this will result in excessive bearing wear and

premature failure.

mounting bracket is provided for mounting on a wall.

The heater should not be mounted in situations where it may be

subject to conditions of excessive humidity or the atmosphere is

corrosive.

INSTALLATION

To the unit connect a suitable length of 3 or 4 core flexible

cable to the input terminal block.

Loosen mounting screws, allowing the mounting bracket to be

removed from the unit. Making sure that the mounting bracket

is horizontal, fix the bracket to the wall using 3 x No 8 wood

screws.

Place the unit on the mounting bracket ensuring the washers are

spaced as on diagram (a plain washer either side of the

mounting bracket).

Tighten screws to hold the unit at the required angle.

ELECTRICAL CONNECTIONS

These units are suitable for connection to a 230/240V 50Hz

single phase ac supply. The units consume 3kW of electrical

power when the fan and heater are in operation.

To connect a supply to the heater, first remove the top cover by

unscrewing the 4 fixing screws (2 either side), then lifting off

the cover. The input terminal block, marked NFH, is fitted at

the left hand side of the unit looking from above (at the

opposite end to the fan motor).

double-pole isolator switch should be included in the

installation.

44000070 Iss 04

OPERATION

This he ter is controlled by Celsi Zone Controller CZC1 nd

c n only be used when connected. Each CZC1 can control any

number of heaters. The heater has an indicator light positioned

on the fascia panel on the top left side. The light may be:

Green - when no heat is needed

Yellow - when some heat is needed to maintain

the room temperature

Red - when the heater is on full power

F st Fl shing Red - when the heater has overheated and an

Electronic Safety Control has switched

the heater off.

Please refer to the user and operating instructions for the CZC1

for detailed instructions.

ELECTRONIC SAFETY CONTROL

The appliance is fitted with an Electronic Safety Control (ES).

This is a safety device which switches the heater off if, for any

reason, the appliance overheats. The overheating is indicated

by fast flashing red light. The ES control can only be re-set

after the appliance has cooled down. In order to re-set the ES

control, proceed as follows:

•Switch the appliance off at the mains by using the isolator

switch and leave to cool down for approximately 5 minutes.

•Switch appliance back on and the ES control will re-set.

•Ensure that the appliance is functioning correctly. If the ES

control operates again, the appliance should be checked by

a competent electrician.

MAINTENANCE

LW YS ENSURE TH T THE M IN EXTERN L ELECTRICITY SUPPLY

IS SWITCHED OFF BEFORE TTENDING TO THE SERVICING OF THE

UNIT.

To obtain the best results from Heat-Zone it is necessary to

avoid any build-up of dust or dirt within the unit or on the air

inlet grille. For this reason the unit should be cleaned regularly,

paying particular attention to the removal of dirt build-up on

the back of the fan rotor blades.

The remov l of dust nd dirt is best chieved using soft

brush.

TO REMOVE THE FAN HEATER ASSEMBLY

a) Remove the top cover as described under the heading

‘Electrical Connection’.

b) Disconnect the supply wires to the input terminal block and

earth post.

c) Unscrew the bush holding the terminal block assembly to

the main case.

d) Remove the 4 nuts and washers holding the fan heater

assembly in place.

e) The fan heater assembly, terminal block and internal wiring

can now be removed.

The assembly is replaced by carrying out the above operations in

the order e) to a).

SPARES

It is essential when ordering spares or replacement parts to

state the model number and serial number on the rating plate

fixed to the top of the unit.

In the interest of progress the Company reserves the right to

vary specifications from time to time without notice. The

material listed is offered subject to the Company’s General

Conditions of Sale, a copy of which may be obtained by request.

Autres manuels Claudgen Chauffage

Claudgen

Claudgen ScreenZone RAC10HL Manuel utilisateur

Claudgen

Claudgen ScreenZone CA2015S Manuel utilisateur

Claudgen

Claudgen HE7237SL Manuel utilisateur

Claudgen

Claudgen HE7237 Manuel

Claudgen

Claudgen SCREENZONE RAC1306 Manuel utilisateur

Claudgen

Claudgen HE6351 Manuel

Claudgen

Claudgen HE7010W-30 Manuel

Claudgen

Claudgen HE8320RF Manuel

Claudgen

Claudgen RAC1509 Manuel utilisateur

Claudgen

Claudgen ScreenZone CA1514S10 Manuel utilisateur

Claudgen

Claudgen HE7402-31 Manuel

Claudgen

Claudgen HE8320 Manuel

Claudgen

Claudgen HE7230SL Manuel utilisateur

Claudgen

Claudgen Sanfire 40 Manuel

Claudgen

Claudgen CH06CS Manuel

Claudgen

Claudgen HE8326-33 Manuel

Claudgen

Claudgen CH06CSi Manuel utilisateur

Claudgen

Claudgen CA1309S Manuel

Claudgen

Claudgen CA1309S Instructions d'utilisation d'origine

Claudgen

Claudgen HE8515 Manuel

Claudgen

Claudgen RCT250SL Manuel d'utilisation et d'entretien

Claudgen

Claudgen HE7230 Manuel utilisateur

Claudgen

Claudgen SCREENZONE RAC1306 Manuel utilisateur

Claudgen

Claudgen HE7402RF Manuel

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur